On some platforms (MacPro3,1) the BIOS assigns the ioatdma device to the
incorrect iommu causing faults when the driver initializes.  Add a quirk
to catch this misconfiguration and try falling back to untranslated
operation (which works in the MacPro3,1 case).

Assuming there are other platforms with misconfigured iommus teach the
ioatdma driver to treat initialization failures as non-fatal (just fail
the driver load and emit a warning instead of triggering a BUG_ON).

This can be classified as a boot regression since 2.6.32 on affected
platforms since the ioatdma module did not autoload prior to that
kernel.

Cc: <stable@kernel.org>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Reported-by: Chris Li <lkml@chrisli.org>
Tested-by: Chris Li <lkml@chrisli.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

This extends the DMA engine driver for the COH 901 318 used in the
U300 platform with the generic runtime slave control command.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

This extends the DMA engine driver for the DMA40 used in the
U8500 platform with the generic runtime slave configuration
interface.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

This adds an interface to the DMAengine to make it possible to
reconfigure a slave channel at runtime. We add a few foreseen
config parameters to the passed struct, with a void * pointer
for custom per-device or per-platform runtime slave data.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Topcliff PCH is the platform controller hub that is going to
be used in Intel's upcoming general embedded platforms. This
adds the driver for Topcliff PCH DMA controller. The DMA
channels are strictly for device to host or host to device
transfers and cannot be used for generic memcpy.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
[kill GFP_ATOMIC, kill __raw_{read|write}l, locking fixlet]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

This patch add DMA drivers for DMA controllers in Langwell chipset
of Intel(R) Moorestown platform and DMA controllers in Penwell of
Intel(R) Medfield platfrom

This patch adds support for Moorestown DMAC1 and DMAC2 controllers.
It also add support for Medfiled GP DMA and DMAC1 controllers.
These controllers supports memory to peripheral and peripheral to
memory transfers. It support only single block transfers.

This driver is based on Kernel DMA engine
Anyone who wishes to use this controller should use DMA engine APIs

This controller exposes DMA_SLAVE capabilities and notifies the client drivers
of DMA transaction completion

Config option required to be enabled CONFIG_INTEL_MID_DMAC=y
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

If td_desc is NULL, just skip both kfrees.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@

if ((E == NULL && ...) || ...)
{
  ... when != if (...) S1 else S2
      when != E = E1
* E->f
  ... when any
  return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

This silences a compile warning on 32 bit systems:
drivers/dma/timb_dma.c:203: warning: cast to pointer from integer of different size
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

This makes sure the DMA40 driver will also work on the oldest
silicon revisions that have the on-chip memory on another location
in the DB8500 and also requires explicit suspend before starting
or resuming a logical channel.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
[added parenthesis to the definition of U8500_DMA_LCPA_BASE_ED]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

This makes it possible to disable physical channels.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Make sure we have no disabled physical channels when we start on
the ux500 machines.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

This fixes a bug when suspending channels: first make the checks,
then suspend the channel, not the other way around.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

This adds all available memcpy channels to the DB8500 in the
ux500 platform (and fixes a typo).
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

On memcpy DMA operations we don't need flow control.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

This follows on the patch to allocate LCLA dynamically: the
on-chip memory is needed for other things so now that that
we're using it dynamically we can remove the LCLA resource
altogether and free up some ESRAM memory.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Switch to allocating LCLA in memory instead of having a fixed
address.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Correct bug that could cause paused channels to stop.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

We don't want interrupts when the source is done, only when
the destination is done and everything is complete at the
recieveing end of a transfer.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Avoid doing unnessecary suspend when modifying logical channels.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Fix up some locking issues found by enabling lock debugging.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Added checks to deny operating on none-allocated channels.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

This cleans up some extra newlines, removes some code duplication
and moves the code to comply better with checkpatch.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Better error handling when channel allocation fails.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Use kmem cache instead of own cache, reducing code duplication
and bug sources.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

fixed typo and moved freeing of client owned desc to free_dma.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

We only need to write the configuration to a physical channel if
it is free, else it is already written.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Fixed lli_max=1 issue in case of full lcla, currently this case
is not properly handled.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  wimax/i2400m: fix missing endian correction read in fw loader
  net8139: fix a race at the end of NAPI
  pktgen: Fix accuracy of inter-packet delay.
  pkt_sched: gen_estimator: add a new lock
  net: deliver skbs on inactive slaves to exact matches
  ipv6: fix ICMP6_MIB_OUTERRORS
  r8169: fix mdio_read and update mdio_write according to hw specs
  gianfar: Revive the driver for eTSEC devices (disable timestamping)
  caif: fix a couple range checks
  phylib: Add support for the LXT973 phy.
  net: Print num_rx_queues imbalance warning only when there are allocated queues

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM / x86: Save/restore MISC_ENABLE register

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: The file argument for fsync() is never null
  Btrfs: handle ERR_PTR from posix_acl_from_xattr()
  Btrfs: avoid BUG when dropping root and reference in same transaction
  Btrfs: prohibit a operation of changing acl's mask when noacl mount option used
  Btrfs: should add a permission check for setfacl
  Btrfs: btrfs_lookup_dir_item() can return ERR_PTR
  Btrfs: btrfs_read_fs_root_no_name() returns ERR_PTRs
  Btrfs: unwind after btrfs_start_transaction() errors
  Btrfs: btrfs_iget() returns ERR_PTR
  Btrfs: handle kzalloc() failure in open_ctree()
  Btrfs: handle error returns from btrfs_lookup_dir_item()
  Btrfs: Fix BUG_ON for fs converted from extN
  Btrfs: Fix null dereference in relocation.c
  Btrfs: fix remap_file_pages error
  Btrfs: uninitialized data is check_path_shared()
  Btrfs: fix fallocate regression
  Btrfs: fix loop device on top of btrfs

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: clear bridge resource range if BIOS assigned bad one
  PCI: hotplug/cpqphp, fix NULL dereference
  Revert "PCI: create function symlinks in /sys/bus/pci/slots/N/"
  PCI: change resource collision messages from KERN_ERR to KERN_INFO

Yannick found that video does not work with 2.6.34.  The cause of this
bug was that the BIOS had assigned the wrong range to the PCI bridge
above the video device.  Before 2.6.34 the kernel would have shrunk
the size of the bridge window, but since
  d65245c3 PCI: don't shrink bridge resources
the kernel will avoid shrinking BIOS ranges.

So zero out the old range if we fail to claim it at boot time; this will
cause us to allocate a new range at startup, restoring the 2.6.34
behavior.

Fixes regression https://bugzilla.kernel.org/show_bug.cgi?id=16009.
Reported-by: Yannick <yannick.roehlly@free.fr>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

There are devices out there which are PCI Hot-plug controllers with
compaq PCI IDs, but are not bridges, hence have pdev->subordinate
NULL. But cpqphp expects the pointer to be non-NULL.

Add a check to the probe function to avoid oopses like:
BUG: unable to handle kernel NULL pointer dereference at 00000050
IP: [<f82e3c41>] cpqhpc_probe+0x951/0x1120 [cpqphp]
*pdpt = 0000000033779001 *pde = 0000000000000000
...

The device here was:
00:0b.0 PCI Hot-plug controller [0804]: Compaq Computer Corporation PCI Hotplug Controller [0e11:a0f7] (rev 11)
	Subsystem: Compaq Computer Corporation Device [0e11:a2f8]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

This reverts commit 75568f80.

Since they're just a convenience anyway, remove these symlinks since
they're causing duplicate filename errors in the wild.
Acked-by: Alex Chiang <achiang@canonical.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

We can often deal with PCI resource issues by moving devices around.  In
that case, there's no point in alarming the user with messages like these.
There are many bug reports where the message itself is the only problem,
e.g., https://bugs.launchpad.net/ubuntu/+source/linux/+bug/413419 .
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

The "file" argument for fsync is never null so we can remove this check.

What drew my attention here is that 7ea80859: "drop unused dentry
argument to ->fsync" introduced an unconditional dereference at the
start of the function and that generated a smatch warning.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

posix_acl_from_xattr() returns both ERR_PTRs and null, but it's OK to
pass null values to set_cached_acl()
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

If btrfs_ioctl_snap_destroy() deletes a snapshot but finishes
with end_transaction(), the cleaner kthread may come in and
drop the root in the same transaction.  If that's the case, the
root's refs still == 1 in the tree when btrfs_del_root() deletes
the item, because commit_fs_roots() hasn't updated it yet (that
happens during the commit).

This wasn't a problem before only because
btrfs_ioctl_snap_destroy() would commit the transaction before dropping
the dentry reference, so the dead root wouldn't get queued up until
after the fs root item was updated in the btree.

Since it is not an error to drop the root reference and the root in the
same transaction, just drop the BUG_ON() in btrfs_del_root().
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>