- 30 Mar, 2016 1 commit
-
-
Tushar Dave authored
commit c9f53e63 ("ixgbe: Refactor MAC address configuration code") introduced code that doesn't set HW register RAR0 to default mac address but FF:FF:FF:FF:FF:FF. Due to this, ixgbe HW discards all incoming packets that doesn't have destination mac address equals to FF:FF:FF:FF:FF:FF. This commit sets RAR0 correctly to default HW mac address. Signed-off-by:
Tushar Dave <tushar.n.dave@oracle.com> Tested-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 29 Mar, 2016 1 commit
-
-
Bjørn Mork authored
Thomas reports: "Windows: 00 diagnostics 01 modem 02 at-port 03 nmea 04 nic Linux: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2001 ProdID=7e19 Rev=02.32 S: Manufacturer=Mobile Connect S: Product=Mobile Connect S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage" Reported-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 28 Mar, 2016 19 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for you net tree, they are: 1) There was a race condition between parallel save/swap and delete, which resulted a kernel crash due to the increase ref for save, swap, wrong ref decrease operations. Reported and fixed by Vishwanath Pai. 2) OVS should call into CT NAT for packets of new expected connections only when the conntrack state is persisted with the 'commit' option to the OVS CT action. From Jarno Rajahalme. 3) Resolve kconfig dependencies with new OVS NAT support. From Arnd Bergmann. 4) Early validation of entry->target_offset to make sure it doesn't take us out from the blob, from Florian Westphal. 5) Again early validation of entry->next_offset to make sure it doesn't take out from the blob, also from Florian. 6) Check that entry->target_offset is always of of sizeof(struct xt_entry) for unconditional entries, when checking both from check_underflow() and when checking for loops in mark_source_chains(), again from Florian. 7) Fix inconsistent behaviour in nfnetlink_queue when NFQA_CFG_F_FAIL_OPEN is set and netlink_unicast() fails due to buffer overrun, we have to reinject the packet as the user expects. 8) Enforce nul-terminated table names from getsockopt GET_ENTRIES requests. 9) Don't assume skb->sk is set from nft_bridge_reject and synproxy, this fixes a recent update of the code to namespaceify ip_default_ttl, patch from Liping Zhang. This batch comes with four patches to validate x_tables blobs coming from userspace. CONFIG_USERNS exposes the x_tables interface to unpriviledged users and to be honest this interface never received the attention for this move away from the CAP_NET_ADMIN domain. Florian is working on another round with more patches with more sanity checks, so expect a bit more Netfilter fixes in this development cycle than usual. ==================== Signed-off-by: -
Liping Zhang authored
Commit fa50d974 ("ipv4: Namespaceify ip_default_ttl sysctl knob") use sock_net(skb->sk) to get the net namespace, but we can't assume that sk_buff->sk is always exist, so when it is NULL, oops will happen. Signed-off-by:
Liping Zhang <liping.zhang@spreadtrum.com> Reviewed-by:
Nikolay Borisov <kernel@kyup.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-
Pablo Neira Ayuso authored
Make sure the table names via getsockopt GET_ENTRIES is nul-terminated in ebtables and all the x_tables variants and their respective compat code. Uncovered by KASAN. Reported-by:
Baozeng Ding <sploving1@gmail.com> Signed-off-by:
-
Pablo Neira Ayuso authored
When netlink unicast fails to deliver the message to userspace, we should also check if the NFQA_CFG_F_FAIL_OPEN flag is set so we reinject the packet back to the stack. I think the user expects no packet drops when this flag is set due to queueing to userspace errors, no matter if related to the internal queue or when sending the netlink message to userspace. The userspace application will still get the ENOBUFS error via recvmsg() so the user still knows that, with the current configuration that is in place, the userspace application is not consuming the messages at the pace that the kernel needs. Reported-by:
"Yigal Reiss (yreiss)" <yreiss@cisco.com> Signed-off-by:
-
Florian Westphal authored
Ben Hawkes says: In the mark_source_chains function (net/ipv4/netfilter/ip_tables.c) it is possible for a user-supplied ipt_entry structure to have a large next_offset field. This field is not bounds checked prior to writing a counter value at the supplied offset. Problem is that mark_source_chains should not have been called -- the rule doesn't have a next entry, so its supposed to return an absolute verdict of either ACCEPT or DROP. However, the function conditional() doesn't work as the name implies. It only checks that the rule is using wildcard address matching. However, an unconditional rule must also not be using any matches (no -m args). The underflow validator only checked the addresses, therefore passing the 'unconditional absolute verdict' test, while mark_source_chains also tested for presence of matches, and thus proceeeded to the next (not-existent) rule. Unify this so that all the callers have same idea of 'unconditional rule'. Reported-by:
Ben Hawkes <hawkes@google.com> Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
-
Florian Westphal authored
Otherwise this function may read data beyond the ruleset blob. Signed-off-by:
-
Florian Westphal authored
We should check that e->target_offset is sane before mark_source_chains gets called since it will fetch the target entry for loop detection. Signed-off-by:
-
Arnd Bergmann authored
The openvswitch code has gained support for calling into the nf-nat-ipv4/ipv6 modules, however those can be loadable modules in a configuration in which openvswitch is built-in, leading to link errors: net/built-in.o: In function `__ovs_ct_lookup': :(.text+0x2cc2c8): undefined reference to `nf_nat_icmp_reply_translation' :(.text+0x2cc66c): undefined reference to `nf_nat_icmpv6_reply_translation' The dependency on (!NF_NAT || NF_NAT) prevents similar issues, but NF_NAT is set to 'y' if any of the symbols selecting it are built-in, but the link error happens when any of them are modular. A second issue is that even if CONFIG_NF_NAT_IPV6 is built-in, CONFIG_NF_NAT_IPV4 might be completely disabled. This is unlikely to be useful in practice, but the driver currently only handles IPv6 being optional. This patch improves the Kconfig dependency so that openvswitch cannot be built-in if either of the two other symbols are set to 'm', and it replaces the incorrect #ifdef in ovs_ct_nat_execute() with two "if (IS_ENABLED())" checks that should catch all corner cases also make the code more readable. The same #ifdef exists ovs_ct_nat_to_attr(), where it does not cause a link error, but for consistency I'm changing it the same way. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: 05752523 ("openvswitch: Interface with NAT.") Acked-by:
Joe Stringer <joe@ovn.org> Signed-off-by:
-
Jarno Rajahalme authored
OVS should call into CT NAT for packets of new expected connections only when the conntrack state is persisted with the 'commit' option to the OVS CT action. The test for this condition is doubly wrong, as the CT status field is ANDed with the bit number (IPS_EXPECTED_BIT) rather than the mask (IPS_EXPECTED), and due to the wrong assumption that the expected bit would apply only for the first (i.e., 'new') packet of a connection, while in fact the expected bit remains on for the lifetime of an expected connection. The 'ctinfo' value IP_CT_RELATED derived from the ct status can be used instead, as it is only ever applicable to the 'new' packets of the expected connection. Fixes: 05752523 ('openvswitch: Interface with NAT.') Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Jarno Rajahalme <jarno@ovn.org> Signed-off-by:
-
Vishwanath Pai authored
This fix adds a new reference counter (ref_netlink) for the struct ip_set. The other reference counter (ref) can be swapped out by ip_set_swap and we need a separate counter to keep track of references for netlink events like dump. Using the same ref counter for dump causes a race condition which can be demonstrated by the following script: ipset create hash_ip1 hash:ip family inet hashsize 1024 maxelem 500000 \ counters ipset create hash_ip2 hash:ip family inet hashsize 300000 maxelem 500000 \ counters ipset create hash_ip3 hash:ip family inet hashsize 1024 maxelem 500000 \ counters ipset save & ipset swap hash_ip3 hash_ip2 ipset destroy hash_ip3 /* will crash the machine */ Swap will exchange the values of ref so destroy will see ref = 0 instead of ref = 1. With this fix in place swap will not succeed because ipset save still has ref_netlink on the set (ip_set_swap doesn't swap ref_netlink). Both delete and swap will error out if ref_netlink != 0 on the set. Note: The changes to *_head functions is because previously we would increment ref whenever we called these functions, we don't do that anymore. Reviewed-by:
Joshua Hunt <johunt@akamai.com> Signed-off-by:
Vishwanath Pai <vpai@akamai.com> Signed-off-by:
Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by:
-
Charles Keepax authored
GPIOlib will print warning messages if we call GPIO functions without a valid GPIO. Change the code to avoid doing so. Signed-off-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
-
Lisheng authored
It may fail to set coalesce usecs to HW, and Ethtool needs to know if it is successful to cfg the parameter or not. So it needs return the errno by dsaf.ko. Signed-off-by:
Lisheng <lisheng011@huawei.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
-
Lisheng authored
The overtime setting and getting REGs in HNS V2 is defferent from HNS V1. It needs to be distinguished between them if getting or setting the REGs. Signed-off-by:
-
Haishuang Yan authored
For the input parameter count, it's better to use the size of destination buffer size, as nla_memcpy would take into account the length of the source netlink attribute when a data is copied from an attribute. Signed-off-by:
Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by:
-
Lino Sanfilippo authored
In ravb_start_xmit dont call skb_tx_timestamp only when hardware timestamping is requested: in the latter case software timestamps are suppressed and thus the call of skb_tx_timestamp does not have any effect. Instead call skb_tx_timestamp unconditionally in ravb_start_xmit, since the function checks itself if software timestamping is required or should be skipped due to hardware timestamping. Signed-off-by:
Lino Sanfilippo <LinoSanfilippo@gmx.de> Acked-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Rasmus Villemoes authored
We need to use post-decrement to ensure that irq_dispose_mapping is also called on priv->rxq[0]->irq_no; moreover, if one of the above for loops failed already at i==0 (so we reach one of these labels with that value of i), we'll enter an essentially infinite loop of out-of-bounds accesses. Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by:
Francois Romieu <romieu@fr.zoreil.com> Signed-off-by:
-
Cosmin-Gabriel Samoila authored
Fix variable assignment inside if statement. It is error-prone and hard to read. Signed-off-by:
Cosmin-Gabriel Samoila <gabrielcsmo@gmail.com> Signed-off-by:
-
Quentin Armitage authored
For a route with IPv6 encapsulation, the traffic class and hop limit values are interchanged when returned to userspace by the kernel. For example, see below. ># ip route add 192.168.0.1 dev eth0.2 encap ip6 dst 0x50 tc 0x50 hoplimit 100 table 1000 ># ip route show table 1000 192.168.0.1 encap ip6 id 0 src :: dst fe83::1 hoplimit 80 tc 100 dev eth0.2 scope link Signed-off-by:
Quentin Armitage <quentin@armitage.org.uk> Signed-off-by:
-
Diego Viola authored
Signed-off-by:
Diego Viola <diego.viola@gmail.com> Signed-off-by:
-
- 25 Mar, 2016 5 commits
-
-
Cyrille Pitchen authored
This patch removes two BUG_ON() used to notify about RX queue corruptions on macb (not gem) hardware without actually handling the error. The new code skips corrupted frames but still processes faultless frames. Then it resets the RX queue before restarting the reception from a clean state. This patch is a rework of an older patch proposed by Neil Armstrong: http://patchwork.ozlabs.org/patch/371525/Signed-off-by:
Cyrille Pitchen <cyrille.pitchen@atmel.com> Acked-by:
Neil Armstrong <narmstrong@baylibre.com> Acked-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
-
Manish Chopra authored
Just updating version as many fixes got accumulated over 1.00.00.34 Signed-off-by:
Manish Chopra <manish.chopra@qlogic.com> Signed-off-by:
-
Jaedon Shin authored
Add PHY entries for the Broadcom BCM7346 and BCM7362 chips, these are 40nm generation Ethernet PHY. Fixes: 815717d1 ("net: phy: bcm7xxx: Remove wildcard entries") Signed-off-by:
Jaedon Shin <jaedon.shin@gmail.com> Signed-off-by:
-
Daniel Borkmann authored
Add map_flags attribute to bpf_map_show_fdinfo(), so that tools like tc can check for them when loading objects from a pinned entry, e.g. if user intent wrt allocation (BPF_F_NO_PREALLOC) is different to the pinned object, it can bail out. Follow-up to 6c905981 ("bpf: pre-allocate hash map elements"), so that tc can still support this with v4.6. Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Bjorn Helgaas authored
netpoll_setup() does a dev_hold() on np->dev, the netpoll device. If it fails, it correctly does a dev_put() but leaves np->dev set. If we call netpoll_cleanup() after the failure, np->dev is still set so we do another dev_put(), which decrements the refcount an extra time. It's questionable to call netpoll_cleanup() after netpoll_setup() fails, but it can be difficult to find the problem, and we can easily avoid it in this case. The extra decrements can lead to hangs like this: unregister_netdevice: waiting for bond0 to become free. Usage count = -3 Set and clear np->dev at the points where we dev_hold() and dev_put() the device. Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
- 24 Mar, 2016 14 commits
-
-
Petri Gynther authored
skb_len needs to be skb_headlen(skb) in bcmgenet_xmit_single(). Fragmented skbs can have only Ethernet + IP + TCP headers (14+20+20=54 bytes) in the linear buffer, followed by the rest in fragments. Bumping skb_len to ETH_ZLEN would be incorrect for this case, as it would introduce garbage between TCP header and the fragment data. This also works with regular/non-fragmented small packets < ETH_ZLEN bytes. Successfully tested this on GENETv3 with 42-byte ARP frames. For testing, I used: ethtool -K eth0 tx-checksum-ipv4 off ethtool -K eth0 tx-checksum-ipv6 off echo 0 > /proc/sys/net/ipv4/tcp_timestamps Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
Petri Gynther <pgynther@google.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Petri Gynther authored
1. Add bytes_compl local variable to __bcmgenet_tx_reclaim() to collect transmitted bytes. dev->stats updates can then be moved outside the while-loop. bytes_compl is also needed for future BQL support. 2. When bcmgenet device uses Tx checksum offload, each transmitted skb gets an extra 64-byte header prepended to it. Before this header is prepended to the skb, we need to save the skb "wire" length in GENET_CB(skb)->bytes_sent, so that proper Tx bytes accounting can be done in __bcmgenet_tx_reclaim(). 3. skb->len covers the entire length of skb, whether it is linear or fragmented. Thus, when we clean the fragments, do not increase transmitted bytes. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
Nicolas Dichtel authored
Two minor typo. Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Cyrille Pitchen authored
macb_interrupt() should not use macb_writel(bp, ISR, <value>) but only queue_writel(queue, ISR, <value>). There is one IRQ and one set of {ISR, IER, IDR, IMR} [1] registers per queue on gem hardware, though only queue0 is actually used for now to receive frames: other queues can already be used to transmit frames. The queue_readl() and queue_writel() helper macros are designed to access the relevant IRQ registers. [1] ISR: Interrupt Status Register IER: Interrupt Enable Register IDR: Interrupt Disable Register IMR: Interrupt Mask Register Signed-off-by: -
David S. Miller authored
Yisen Zhuang says: ==================== net: hns: fix some bugs in HNS driver Here are some bug fixed patches for HNS driver. They are: >from Kejian, fix for the warning of passing zero to 'PTR_ERR' >from qianqian, four fixes for inappropriate operation in hns driver >from Sheng, one fix for optimization of irq proccess in hns driver, and one fix for hilink status for hns driver. For more details, please see individual patches. ==================== Signed-off-by: -
Sheng Li authored
The hilink status reg in HNS V2 is different from HNS v1. In HNS V2, It distinguishes differnt lane status according to the bit-field of the reg. As is shown below: [0:0] ---> lane0 [1:1] ---> lane1 ... But the current driver reads the reg to get the hilink status ONLY concidering HNS V1 situation. Here is a patch to support both of them. Signed-off-by:
Daode Huang <huangdaode@hisilicon.com> Signed-off-by:
-
Kejian Yan authored
There is a misuse of PTR as shown below: ae_node = (void *)of_parse_phandle(dev->of_node, "ae-handle", 0); if (IS_ERR_OR_NULL(ae_node)) { ret = PTR_ERR(ae_node); dev_err(dev, "not find ae-handle\n"); goto out_read_prop_fail; } if the ae_node is NULL, PTR_ERR(ae_node) means it returns success. And the return value should be -ENODEV. Signed-off-by:Kejian Yan <yankejian@huawei.com> Signed-off-by:
-
Sheng Li authored
In hns V1, common_poll should check and clean fbd pkts, because it can not pend irq to clean them if there is no new pkt comes in. But hns V2 hw fixes this bug, and will pend irq itself to do this. So, for hns V2, we set ring_data->fini_process to NULL. Signed-off-by:
-
Qianqian Xie authored
The variable head in hns_nic_tx_fini_pro has read a value, but it is obviously no use. The patch will fix it. And the comment is nothing to do with the routine, so it has to be removed Signed-off-by:
Qianqian Xie <xieqianqian@huawei.com> Signed-off-by:
-
Qianqian Xie authored
The return values in the first two functions mdiobus_write() are ignored. The patch will fix it. Signed-off-by:
-
Qianqian Xie authored
It misses string format in function snprintf(), as below: snprintf(buff, ETH_GSTRING_LEN, g_gmac_stats_string[i].desc); It needs to add "%s" to fix it as below: snprintf(buff, ETH_GSTRING_LEN, "%s", g_gmac_stats_string[i].desc); Signed-off-by:
-
Qianqian Xie authored
The cycle index should be varied while the variable j is a fixed value. The patch will fix this bug. Signed-off-by:
-
subashab@codeaurora.org authored
A crash is observed when a decrypted packet is processed in receive path. get_rps_cpus() tries to dereference the skb->dev fields but it appears that the device is freed from the poison pattern. [<ffffffc000af58ec>] get_rps_cpu+0x94/0x2f0 [<ffffffc000af5f94>] netif_rx_internal+0x140/0x1cc [<ffffffc000af6094>] netif_rx+0x74/0x94 [<ffffffc000bc0b6c>] xfrm_input+0x754/0x7d0 [<ffffffc000bc0bf8>] xfrm_input_resume+0x10/0x1c [<ffffffc000ba6eb8>] esp_input_done+0x20/0x30 [<ffffffc0000b64c8>] process_one_work+0x244/0x3fc [<ffffffc0000b7324>] worker_thread+0x2f8/0x418 [<ffffffc0000bb40c>] kthread+0xe0/0xec -013|get_rps_cpu( | dev = 0xFFFFFFC08B688000, | skb = 0xFFFFFFC0C76AAC00 -> ( | dev = 0xFFFFFFC08B688000 -> ( | name = "...................................................... | name_hlist = (next = 0xAAAAAAAAAAAAAAAA, pprev = 0xAAAAAAAAAAA Following are the sequence of events observed - - Encrypted packet in receive path from netdevice is queued - Encrypted packet queued for decryption (asynchronous) - Netdevice brought down and freed - Packet is decrypted and returned through callback in esp_input_done - Packet is queued again for process in network stack using netif_rx Since the device appears to have been freed, the dereference of skb->dev in get_rps_cpus() leads to an unhandled page fault exception. Fix this by holding on to device reference when queueing packets asynchronously and releasing the reference on call back return. v2: Make the change generic to xfrm as mentioned by Steffen and update the title to xfrm Suggested-by:Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
Jerome Stanislaus <jeromes@codeaurora.org> Signed-off-by:
Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-traceLinus Torvalds authored
Pull tracing updates from Steven Rostedt: "Nothing major this round. Mostly small clean ups and fixes. Some visible changes: - A new flag was added to distinguish traces done in NMI context. - Preempt tracer now shows functions where preemption is disabled but interrupts are still enabled. Other notes: - Updates were done to function tracing to allow better performance with perf. - Infrastructure code has been added to allow for a new histogram feature for recording live trace event histograms that can be configured by simple user commands. The feature itself was just finished, but needs a round in linux-next before being pulled. This only includes some infrastructure changes that will be needed" * tag 'trace-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (22 commits) tracing: Record and show NMI state tracing: Fix trace_printk() to print when not using bprintk() tracing: Remove redundant reset per-CPU buff in irqsoff tracer x86: ftrace: Fix the misleading comment for arch/x86/kernel/ftrace.c tracing: Fix crash from reading trace_pipe with sendfile tracing: Have preempt(irqs)off trace preempt disabled functions tracing: Fix return while holding a lock in register_tracer() ftrace: Use kasprintf() in ftrace_profile_tracefs() ftrace: Update dynamic ftrace calls only if necessary ftrace: Make ftrace_hash_rec_enable return update bool tracing: Fix typoes in code comment and printk in trace_nop.c tracing, writeback: Replace cgroup path to cgroup ino tracing: Use flags instead of bool in trigger structure tracing: Add an unreg_all() callback to trigger commands tracing: Add needs_rec flag to event triggers tracing: Add a per-event-trigger 'paused' field tracing: Add get_syscall_name() tracing: Add event record param to trigger_ops.func() tracing: Make event trigger functions available tracing: Make ftrace_event_field checking functions available ...
-
