From Shawn Guo:
The imx soc changes for 3.10:

* Enable anatop, well bisa and RBC for suspend to optimize the power
  consumption a little bit
* Clock changes for TVE, LDB, PATA, SRTC support
* Add System Reset Controller (SRC) support for imx5 and imx6
* Add initial imx6dl support based on imx6q code
* Kconfig for cpufreq-cpu0, defconfig updates and few other changes

* tag 'imx-soc-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6: (275 commits)
  ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
  ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
  ARM i.MX53: make tve_ext_sel propagate rate change to PLL
  ARM i.MX53: Remove unused tve_gate clkdev entry
  ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
  ARM: i.MX5: Add PATA and SRTC clocks
  ARM: imx: do not bring up unavailable cores
  ARM: imx: add initial imx6dl support
  ARM: imx1: mm: add call to mxc_device_init
  ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
  ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
  ARM: i.MX53 Add the cko1, cko2 clock outputs.
  staging: drm/imx: Use SRC to reset IPU
  ARM i.MX6q: Add GPU, VPU, IPU, and OpenVG resets to System Reset Controller (SRC)
  ARM: imx: do not use regmap_read for ANADIG_DIGPROG
  ARM i.MX6q: set the LDB serial clock parent to the video PLL
  ARM i.MX6q: Add audio/video PLL post dividers for i.MX6q rev 1.1
  ARM i.MX6q: fix ldb di divider and selector clocks
  ARM i.MX53: fix ldb di divider and selector clocks
  ARM i.MX: Add imx_clk_divider_flags and imx_clk_mux_flags
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Trivial change/change conflict in arch/arm/mach-imx/mach-imx6q.c resolved.

Use imx_clk_mux_flags to set the appropriate flags for the TVE
selector clock. This is needed so tve_clk rate changes can propagate
up to pll4_sw.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Remove the tve_di clock from the CCM clock tree. It will be provided
by the Television Encoder driver, as this clock is an output signal
of the TVE module.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This is needed so the Television Encoder driver can set the rate
on tve_clk and have it propagated up to pll4_sw.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

On i.MX53, there is only tve_ext_sel.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This adds the clock gates and the binding documentation
for PATA and SRTC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The i.MX6 Quad can be fused as i.MX6 Dual chip, and similarly i.MX6
DualLite can be fused as i.MX6 Solo.  The actual number of available
cores can be found out from SCU.

Since we do not reflect the fusing thing in device tree, the function
arm_dt_init_cpu_maps() will always call set_cpu_possible(true) for 4
cores on i.MX6 Quad/Dual and 2 cores for i.MX6 DualLite/Solo.  This
causes failures when kernel tries to bring those unavailable cores
online.  For example, the following failure message will be seen when
booting an i.MX6 Solo chip.

  CPU1: failed to come online

Though kernel will still boot fine, the message is somehow annoying.
Let's get rid of it by calling set_cpu_possible(false) on those
unavailable cores.

While at it, the set_cpu_possible(true) for available cores is removed,
since it's already been done in arm_dt_init_cpu_maps().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The i.MX6 DualLite/Solo is another i.MX6 family SoC, which is highly
compatible with i.MX6 Quad/Dual.  And that's why we choose to support
it using imx6q code with cpu_is_imx6dl() check when necessary.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

mxc_device_init() is mandatory for mxc_aips and mxc_ahb bus registration, needed
as parents, at least, for gpio and dma.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add CONFIG_GPIO_SYSFS as it is helpful for accessing GPIO from userspace.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Select CONFIG_PERF_EVENTS so that oprofile can be used.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

These two clocks connect to external pins and can be muxed to
various internal clocks.
They are typically used either for debugging or to provide
clocks to external chips (eg audio codecs).

Currently only the selectable clocks that already exist in the clock tree
have been added.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Request the System Reset Controller to reset the IPU if
specified via device tree phandle.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The SRC has auto-deasserting reset bits that control reset lines to
the GPU, VPU, IPU, and OpenVG IP modules. This patch adds a reset
controller that can be controlled by those devices using the
reset controller API.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Function imx_anatop_get_digprog() that reads register ANADIG_DIGPROG is
called to identify silicon version.  Users might query silicon version
earlier than regmap subsystem is ready.  For example, imx6q clock driver
query revision in mx6q_clocks_init(), where regmap is not initialized
yet.

Change imx_anatop_get_digprog() to map anatop block and read
ANADIG_DIGPROG in the native way, so that the function can work at very
early stage.

While at it, let's move imx_print_silicon_rev() back to
imx6q_timer_init() to have the message show up a little earlier.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

On i.MX6q revision 1.1 and later, set the video PLL as parent for
the LDB clock branch. On revision 1.0, the video PLL is useless
due to missing dividers, so keep the default parent (mmdc_ch1_axi).
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Query silicon revision to determine clock tree and add post
dividers for newer revisions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Use imx_clk_mux_flags and imx_clk_divider_flags to set the appropriate
flags for the LDB display interface divider and selector clocks.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Use imx_clk_mux_flags and imx_clk_divider_flags to set the appropriate
flags for the LDB display interface divider and selector clocks.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The default is for dividers to set CLK_SET_PARENT_RATE and for muxes to
not set that flag. In the LDB clock tree, we need the opposite, so add
functions to create divider and mux clocks with configurable flags.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

So it can be used in clk-imx6q.c for revision dependent clock tree setup.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

There are some config options not selected by imx27 and imx5 that are
necessary to use the cpufreq-cpu0 driver.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This patch adds the missing GPU2D and GPU3D mux and gate clocks,
and the graphics arbiter gate clock.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Fix the following sparse warnings:

arch/arm/mach-imx/anatop.c:56:6: warning: symbol 'imx_anatop_pre_suspend' was not declared. Should it be static?
arch/arm/mach-imx/anatop.c:62:6: warning: symbol 'imx_anatop_post_resume' was not declared. Should it be static?
arch/arm/mach-imx/anatop.c:68:6: warning: symbol 'imx_anatop_usb_chrg_detect_disable' was not declared. Should it be static?
arch/arm/mach-imx/anatop.c:78:5: warning: symbol 'imx_anatop_get_digprog' was not declared. Should it be static?
arch/arm/mach-imx/anatop.c:86:13: warning: symbol 'imx_anatop_init' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

RBC is to control whether some ANATOP sub modules
can enter lpm mode when SOC is into STOP mode, if
RBC is enabled and PMIC_VSTBY_REQ is set, ANATOP
will have below behaviors:

1. Digital LDOs(CORE, SOC and PU) are bypassed;
2. Analog LDOs(1P1, 2P5, 3P0) are disabled;

As the 2P5 is necessary for DRAM IO pre-drive in
STOP mode, so we need to enable weak 2P5 in STOP
mode when 2P5 LDO is disabled.

For RBC settings, there are some rules as below
due to hardware design:

1. All interrupts must be masked during operating
   RBC registers;
2. At least 2 CKIL(32K) cycles is needed after the
   RBC setting is changed.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Enable periphery charge pump for well biasing
at suspend to reduce periphery leakage.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Anatop module have sereval configurations for user
to reduce the power consumption in suspend, provide
suspend/resume interface for further use and enable
fet_odrive to reduce CORE LDO leakage during suspend.

As we have a common anatop file, remove all the operations
of anatop module in other files, use anatop interfaces to
do that.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The imx cleanup for 3.10:

* Clean up a couple of unneeded function declarations
* Remove imx specific cpufreq driver as generic cpufreq-cpu0 works well
  as the replacement
* Remove platform ahci support
* Clean up unused ARCH/MACH Kconfig symbols
* Remove a couple of unused files

The imx fixes for 3.9, take 5:

* A couple imx35 clock fixes for regressions caused by common clock
  framework conversion.  The admux and iomux get disabled by common
  clock framework late initcall, and hence causes problems.
* Add missing twd clock lookup in device tree.  This becomes required
  since commit bd603455 (ARM: use device tree to get smp_twd clock)
  forces all DT boot to find lookup from device tree.
* Fix imx6q ldb_di clock parents mismatch per reference manual.

"rstc" is NULL here and we should use "rcdev" instead of "rstc->rcdev".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

This adds a simple API for devices to request being reset
by separate reset controller hardware and implements the
reset signal device tree binding.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Pavel Machek <pavel@ucw.cz>

This binding is intended to represent the hardware reset signals present
internally in most IC (SoC, FPGA, ...) designs.
It consists of a binding for a reset controller device (provider), and a
pair of properties, "resets" and "reset-names", to link a device node
(consumer) to its reset controller via phandle, similarly to the clock
and interrupt bindings.

The reset controller has all information necessary to reset the consumer
device. That could be provided via device tree, or it could be implemented
in hardware.
The aim is to enable device drivers to request a framework API to issue a
reset simply by providing their struct device pointer as the most common
case.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Rob Herring <rob.herring@calxeda.com>

Merge tag 'renesas-soc-r8a7790-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc2

From Simon Horman:
Renesas ARM based r8a7790 SoC update for v3.10

* Force architecture timer to be activated regardless of bootloader
  - This is necessary for the lager board to boot
* Add second memory range to r8a7790 PFC device
  - This is in preparation for further PFC work.
    It should not break anything as it is not used yet.

This pull request is based on:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git renesas-soc2-for-v3.10

* tag 'renesas-soc-r8a7790-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: force enable of r8a7790 arch timer
  ARM: shmobile: Add second I/O range for r8a7790 PFC
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-pinmux-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc2

From Simon Horman:
Renesas ARM and SH based SoC pinmux fixes for v3.10

Correct a typo in sh-pfc r8a7779

* tag 'renesas-pinmux-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  sh-pfc: r8a7779: tidyup intc_irq3_b typo
Signed-off-by: Olof Johansson <olof@lixom.net>

This removes the unused Kconfig options ARCH_MX5, ARCH_MX51,
ARCH_MX53 and MACH_MX21.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The i.MX53 ahci platform support is unused in mainline. To demotivate
people using it just remove it from the tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Merge tag 'renesas-soc-r8a7778-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc2

From Simon Horman <horms+renesas@verge.net.au>:

Renesas ARM r8a7778 SoC update for v3.10

Update to the r8a7778 SoC:
* Add SH Ethernet support
* Add r8a7778_init_irq_extpin() to allow configuration of IRQ0 - IRQ3
  - This is a requirement for SMSC ethernet support
* Cleanup: remove PLATFORM_INFO macro

This pull request is based on:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10

* tag 'renesas-soc-r8a7778-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: R8A7778: add Ether support
  ARM: shmobile: r8a7778: add r8a7778_init_irq_extpin()
  ARM: shmobile: r8a7778: remove pointless PLATFORM_INFO()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-soc-r8a7779-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc2

From Simon Horman <horms+renesas@verge.net.au>:

Renesas ARM r8a7779 SoC update for v3.10

Update to the r8a7779 SoC:
* Add SH Ethernet support
* Add comment describing clock ratios

This pull request is based on:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10

* tag 'renesas-soc-r8a7779-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: R8A7779: add Ether support
  ARM: shmobile: r8a7779: add each clocks ratio on comment area
Signed-off-by: Arnd Bergmann <arnd@arndb.de>