Fix the "pciehp probing slow" problem reported from Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.

The command completed bit in Slot Status register applies only to
commands issued to control the attention indicator, power indicator,
power controller, or electromechanical interlock. However, writes to
other parts of the Slot Control register would end up writing to the
control fields. Hence, any write to Slot Control register is
considered as a command. However, if the controller doesn't support
any of attention indicator, power indicator, power controller and
electromechanical interlock, command completed bit would not set in
writing to Slot Control register. In this case, we should not wait for
command completed bit set, otherwise all commands would be considered
not completed in timeout seconds (1 sec.).

The cause of the problem is pciehp driver didn't take this situation
into account. This patch changes pciehp to take it into account. This
patch also add the check for "No Command Completed Support" bit in
Slot Capability register. If it is set, we should not wait for command
completed bit set as well.

This problem seems to be revealed by the commit
c27fb883 that fixed the bug that
pciehp did not wait for command completed properly (pciehp just
ignored the command completion event).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Fix the following NULL dereference problem reported from Pierre Ossman
and Ingo Molnar.

pciehp: HPC vendor_id 8086 device_id 27d0 ss_vid 0 ss_did 0
pciehp: pciehp_find_slot: slot (device=0x0) not found
BUG: unable to handle kernel NULL pointer dereference at 0000000000000070
IP: [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
PGD 0
Oops: 0000 [1]
CPU 0
Modules linked in:
Pid: 1, comm: swapper Tainted: G        W 2.6.26-rc3-sched-devel.git-00001-g2b99b26-dirty #170
RIP: 0010:[<ffffffff80494a8b>]  [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
RSP: 0000:ffff81003f83fbb0  EFLAGS: 00010046
RAX: 0000000000000039 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000046
RBP: ffff81003f83fbd0 R08: 0000000000000001 R09: ffffffff80245103
R10: 0000000000000020 R11: 0000000000000000 R12: ffff81003ea53a30
R13: 0000000000000000 R14: 0000000000000011 R15: ffffffff80495926
FS:  0000000000000000(0000) GS:ffffffff80be7400(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000070 CR3: 0000000000201000 CR4: 00000000000006a0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 1, threadinfo ffff81003f83e000, task ffff81003f840000)
Stack:  0000000000000008 ffff81003f83fbf6 ffff81003ea53a30 0000000000000008
 ffff81003f83fc10 ffffffff80495ab4 0000000000000011 0000000000000002
 0000000000000202 0000000000000202 00000000fffffff4 ffff81003ea53a30
Call Trace:
 [<ffffffff80495ab4>] pcie_isr+0x18e/0x1bc
 [<ffffffff80260831>] request_irq+0x106/0x12f
 [<ffffffff80495fb6>] pcie_init+0x15e/0x6cc
 [<ffffffff804933a3>] pciehp_probe+0x64/0x541
 [<ffffffff8048f4e7>] pcie_port_probe_service+0x4c/0x76
 [<ffffffff8054af70>] driver_probe_device+0xd4/0x1f0
 [<ffffffff8054b108>] __driver_attach+0x7c/0x7e
 [<ffffffff8054b08c>] ? __driver_attach+0x0/0x7e
 [<ffffffff8054a4b6>] bus_for_each_dev+0x53/0x7d
 [<ffffffff8054ad3c>] driver_attach+0x1c/0x1e
 [<ffffffff8054a9c2>] bus_add_driver+0xdd/0x25b
 [<ffffffff80c09d3d>] ? pcied_init+0x0/0x8b
 [<ffffffff8054b288>] driver_register+0x5f/0x13e
 [<ffffffff80c09d3d>] ? pcied_init+0x0/0x8b
 [<ffffffff8048f441>] pcie_port_service_register+0x47/0x49
 [<ffffffff80c09d52>] pcied_init+0x15/0x8b
 [<ffffffff80bf3938>] kernel_init+0x75/0x243
 [<ffffffff808639d2>] ? _spin_unlock_irq+0x2b/0x3a
 [<ffffffff80228d1f>] ? finish_task_switch+0x57/0x9a
 [<ffffffff8020c258>] child_rip+0xa/0x12
 [<ffffffff8020bcec>] ? restore_args+0x0/0x30
 [<ffffffff80bf38c3>] ? kernel_init+0x0/0x243
 [<ffffffff8020c24e>] ? child_rip+0x0/0x12

Code: 83 80 00 00 00 48 39 f0 75 e1 0f b6 c9 48 c7 c2 00 0e 8d 80 48 c7 c6 8a 60 a6 80 48 c7 c7 10 db a8 80 31 c0 e8 3f 8d d9 ff 31 db <48> 8b 43 70 48 8d 75 ef 48 89 df ff 50 30 80 7d ef 00 74 37 48
RIP  [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
 RSP <ffff81003f83fbb0>
CR2: 0000000000000070
Kernel panic - not syncing: Fatal exception

The situation under which it occurs is hw and timing related: it appears
to happen on a system that has PCI hotplug hardware but with no active
hotplug cards, and another interrupt in the same (shared) IRQ line
arrives too early, before the hotplug-slot entry has been set up - as
triggered by CONFIG_DEBUG_SHIRQ=y:

This patch contains the following two fixes.

(1) Clear all events bits in Slot Status register to prevent the pciehp
    driver from detecting the spurious events that would have been occur
    before pciehp loading.

(2) Add check whether slot initialization had been already done.

This is short term fix. We need more structural fixes to install
interrupt handler after slot initialization is done.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The shpchp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

The Slot 03:00.* of JMicron controller has two functions, but one is
PCIE endpoint the other isn't PCIE device, very strange. PCIE spec
defines all functions should have the same config for ASPM, so disable
ASPM for the whole slot in this case.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Forgot to update the PCI error handling address with the new @vger one.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Replace Redundant Whitelist Entries with the Correct Ones

The ProLiant DL585 G2 and the DL585 G2 are entered reundantly in the
dmi_system_id table. What should have been there are the DL360 and DL380. This
patch simply replaces the redundant entries with the correct entries.
Signed-off-by: Tony Camuso <tony.camuso@hp.com>
Signed-off-by: Pat Schoeller <patrick.schoeller@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] macintosh: Replace deprecated __initcall with device_initcall
  [POWERPC] cell: Fix section mismatches in io-workarounds code
  [POWERPC] spufs: Fix compile error
  [POWERPC] Fix uninitialized variable bug in copy_{to|from}_user
  [POWERPC] Add null pointer check to of_find_property
  [POWERPC] vmemmap fixes to use smaller pages
  [POWERPC] spufs: Fix pointer reference in find_victim
  [POWERPC] 85xx: SBC8548 - Add flash support and HW Rev reporting
  [POWERPC] 85xx: Fix some sparse warnings for 85xx MDS
  [POWERPC] 83xx: Enable DMA engine on the MPC8377 MDS board.
  [POWERPC] 86xx: mpc8610_hpcd: fix second serial port
  [POWERPC] 86xx: mpc8610_hpcd: add support for NOR and NAND flashes
  [POWERPC] 85xx: Add 8568 PHY workarounds to board code
  [POWERPC] 86xx: mpc8610_hpcd: use ULI526X driver for on-board ethernet

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  jbd2: update transaction t_state to T_COMMIT fix
  ext4: Retry block allocation if new blocks are allocated from system zone.
  ext4: mballoc fix mb_normalize_request algorithm for 1KB block size filesystems
  ext4: fix typos in messages and comments (journalled -> journaled)
  ext4: fix synchronization of quota files in journal=data mode
  ext4: Fix mount messages when quota disabled
  ext4: correct mount option parsing to detect when quota options can be changed

This patch fixes a build bug on m68k - gcc decides to emit a call to the
strlen library function, which we don't implement.

More importantly - my previous patch "init: don't lose initcall return
values" (commit e662e1cf) had introduced
potential buffer overflow by wrong calculation of string accumulator
size.

Use strlcat() instead, fixing both bugs.

Many thanks Andreas Schwab and Geert Uytterhoeven for helping
to catch and fix the bug.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

One function to just loop over the entries, one function to actually do
the call and the associated debugging code.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Everybody wants to pass it a function pointer, and in fact, that is what
you _must_ pass it for it to make sense (since it knows that ia64 and
ppc64 use descriptors for function pointers and fetches the actual
address from there).

So don't make the argument be a 'unsigned long' and force everybody to
add a cast.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] fix personality(PER_LINUX32) performance issue
  [IA64] Properly unregister legacy interrupts
  [IA64] Remove NULL pointer check for argument never passed as NULL.
  [IA64] trivial cleanup for perfmon.c
  [IA64] trivial cleanup for entry.S
  [IA64] fix interrupt masking for pending works on kernel leave
  [IA64] allow user to force_pal_cache_flush
  [IA64] Don't reserve crashkernel memory > 4 GB
  [IA64] machvec support for SGI UV platform
  [IA64] Add header files for SGI UV platform

Updating the current transaction's t_state is protected by j_state_lock.  We
need to do the same when updating the t_state to T_COMMIT.
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

If the block allocator gets blocks out of system zone ext4 calls
ext4_error. But if the file system is mounted with errors=continue
retry block allocation. We need to mark the system zone blocks as
in use to make sure retry don't pick them again

System zone is the block range mapping block bitmap, inode bitmap and inode
table.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

Enabling the BKL to be lockdep tracked uncovered the following
upstream kernel bug in the tty code, which caused a BKL
reference leak:

  ================================================
  [ BUG: lock held when returning to user space! ]
  ------------------------------------------------
  dmesg/3121 is leaving the kernel with locks still held!
  1 lock held by dmesg/3121:
   #0:  (kernel_mutex){--..}, at: [<c02f34d9>] opost+0x24/0x194

this might explain some of the atomicity warnings and crashes
that -tip tree testing has been experiencing since the BKL
was converted back to a spinlock.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The patch aims to fix a performance issue for the syscall
personality(PER_LINUX32).

On IA-64 box, the syscall personality (PER_LINUX32) has poor performance
because it failed to find the Linux/x86 execution domain. Then it tried
to load the kernel module however it failed always and it used the default
execution domain PER_LINUX instead. Requesting kernel modules is very
expensive. It caused the performance issue. (see the function
lookup_exec_domain in kernel/exec_domain.c).

To resolve the issue, execution domain Linux/x86 is always registered in
initialization time for IA-64 architecture.
Signed-off-by: Xiaolan Huang <xiaolan.huang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] show_interrupts: prevent cpu hotplug when walking cpu_online_map.
  [S390] smp: __smp_call_function_map vs cpu_online_map fix.
  [S390] tape: Use ccw_dev_id to build cdev_id.
  [S390] dasd: fix timeout handling in interrupt handler
  [S390] s390dbf: Use const char * for dbf name.
  [S390] dasd: Use const in busid functions.
  [S390] blacklist.c: removed duplicated include
  [S390] vmlogrdr: module initialization function should return negative errors
  [S390] sparsemem vmemmap: initialize memmap.
  [S390] Remove last traces of cio_msg=.
  [S390] cio: Remove CCW_CMD_SUSPEND_RECONN in front of CCW_CMD_SET_PGID.

* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
  arch/parisc/kernel/perf_asm.S: build fix
  parisc: remove -traditional from assembler flags
  parisc: use conditional macro for 64-bit wide ops
  parisc: Remove ioctl.h content picked up from <asm-generic/ioctl.h>.
  arch/parisc/kernel/unaligned.c: use time_* macros
  parisc: remove redundant display of free swap space in show_mem()
  drivers/parisc: replace remaining __FUNCTION__ occurrences
  parisc: replace remaining __FUNCTION__ occurrences
  parisc: new termios definitions
  parisc: fix trivial section name warnings

Missing <linux/init.h> header for __HEAD macro.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

This work enables us to remove -traditional from $AFLAGS on
parisc.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

Now that <asm-generic/ioctl.h> allows overriding of the most commonly
changed macro values, take advantage of that.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

Surround all the code withing show_interrupts() with
get/put_online_cpus() to prevent strange results wrt cpu hotplug.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Both smp_call_function() and __smp_call_function_map() access
cpu_online_map. Both functions run with preemption disabled which
protects for cpus going offline. However new cpus can be added and
therefore the cpu_online_map can change unexpectedly.
So use the call_lock to protect against changes to the cpu_online_map
in start_secondary() and all smp_call_* functions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

To construct the integer containing the information from the bus_id,
it is easier to use the data from ccw_dev_id than to parse the bus_id.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

When the dasd_int_handler is called with an error code instead of
an irb, the associated request should be restarted. This handling
was missing from the -ETIMEDOUT case. In fact it should be done in
any case.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

We should use const char * for passing the name of the debug feature
around since it will not be changed.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

We should use 'const char *' in the busid functions since the
strings are not modified anyway.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Removed duplicated include <asm/cio.h>
in drivers/s390/cio/blacklist.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Let's just use the generic vmmemmap_alloc_block() function which
always returns initialized memory.

Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

cio_msg= is gone, also remove it from kernel-parameters.txt.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

CCW_CMD_SUSPEND_RECONN causes a system hang if the cable of a
reserved DASD is disconnected and connected again.
Signed-off-by: Michael Ernst <mernst@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The functions time_before, time_before_eq, time_after, and time_after_eq are
more robust for comparing jiffies against other values.

So use the time_after() macro, defined in linux/jiffies.h, which deals with
wrapping correctl

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: S.Caglar Onur <caglar@pardus.org.tr>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

show_mem() has no need to print the amount of free swap space manually because
show_free_areas() does this already and is called by the former.

The two outputs only differ in text formatting:

  printk("Free swap  = %lukB\n", ...);
  printk("Free swap:       %6ldkB\n", ...);
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

This trivial patch fixes the following section warnings on PARISC:
> WARNING: vmlinux.o (.text.1): unexpected section name.
>The (.[number]+) following section name are ld generated and not expected.
> Did you forget to use "ax"/"aw" in a .S file?
> Note that for example <linux/init.h> contains
> section definitions for use in .S files.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>