Make the base offset hexadecimal to simplify debugging since the base
addresses are hex too.

The offsets for connectors is also changed to start after the 'reserved'
range 0x10000-0x2ffff.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70
again after it has already been cleared. Instead it should use the cached
irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since
this has already been done.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org>      # for v3.14 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Defining it as a connector was a bad idea. Remove it while it is
not too late.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Each function range is quite narrow and especially for connectors this
will pose a problem. Increase the function ranges while we still can and
move the connector range to the end so that range is practically limitless.

[mchehab@osg.samsung.com: Rebased to apply at Linus tree]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The adp1653_probe() function may return positive value EINVAL
which is obviously wrong.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add the missing unlock before return from function
vpfe_prepare_pipeline() in the error handling case.

video->lock is lock/unlock in function vpfe_open(),
and no need to unlock it here, so remove unlock
video->lock.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

That prevents this bug:
[ 2382.269496] BUG: unable to handle kernel NULL pointer dereference at 0000000000000540
[ 2382.270013] IP: [<ffffffffa01fe616>] snd_card_free+0x36/0x70 [snd]
[ 2382.270013] PGD 0
[ 2382.270013] Oops: 0002 [#1] SMP
[ 2382.270013] Modules linked in: saa7134_alsa(-) tda1004x saa7134_dvb videobuf2_dvb dvb_core tda827x tda8290 tuner saa7134 tveeprom videobuf2_dma_sg videobuf2_memops videobuf2_v4l2 videobuf2_core v4l2_common videodev media auth_rpcgss nfsv4 dns_resolver nfs lockd grace sunrpc tun bridge stp llc ebtables ip6table_filter ip6_tables nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack it87 hwmon_vid snd_hda_codec_idt snd_hda_codec_generic iTCO_wdt iTCO_vendor_support snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_seq pcspkr i2c_i801 snd_seq_device snd_pcm snd_timer lpc_ich snd mfd_core soundcore binfmt_misc i915 video i2c_algo_bit drm_kms_helper drm r8169 ata_generic serio_raw pata_acpi mii i2c_core [last unloaded: videobuf2_memops]
[ 2382.270013] CPU: 0 PID: 4899 Comm: rmmod Not tainted 4.5.0-rc1+ #4
[ 2382.270013] Hardware name: PCCHIPS P17G/P17G, BIOS 080012  05/14/2008
[ 2382.270013] task: ffff880039c38000 ti: ffff88003c764000 task.ti: ffff88003c764000
[ 2382.270013] RIP: 0010:[<ffffffffa01fe616>]  [<ffffffffa01fe616>] snd_card_free+0x36/0x70 [snd]
[ 2382.270013] RSP: 0018:ffff88003c767ea0  EFLAGS: 00010286
[ 2382.270013] RAX: ffff88003c767eb8 RBX: 0000000000000000 RCX: 0000000000006260
[ 2382.270013] RDX: ffffffffa020a060 RSI: ffffffffa0206de1 RDI: ffff88003c767eb0
[ 2382.270013] RBP: ffff88003c767ed8 R08: 0000000000019960 R09: ffffffff811a5412
[ 2382.270013] R10: ffffea0000d7c200 R11: 0000000000000000 R12: ffff88003c767ea8
[ 2382.270013] R13: 00007ffe760617f7 R14: 0000000000000000 R15: 0000557625d7f1e0
[ 2382.270013] FS:  00007f80bb1c0700(0000) GS:ffff88003f400000(0000) knlGS:0000000000000000
[ 2382.270013] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 2382.270013] CR2: 0000000000000540 CR3: 000000003c00f000 CR4: 00000000000006f0
[ 2382.270013] Stack:
[ 2382.270013]  000000003c767ed8 ffffffff00000000 ffff880000000000 ffff88003c767eb8
[ 2382.270013]  ffff88003c767eb8 ffffffffa049a890 00007ffe76060060 ffff88003c767ef0
[ 2382.270013]  ffffffffa049889d ffffffffa049a500 ffff88003c767f48 ffffffff8111079c
[ 2382.270013] Call Trace:
[ 2382.270013]  [<ffffffffa049889d>] saa7134_alsa_exit+0x1d/0x780 [saa7134_alsa]
[ 2382.270013]  [<ffffffff8111079c>] SyS_delete_module+0x19c/0x1f0
[ 2382.270013]  [<ffffffff8170fc2e>] entry_SYSCALL_64_fastpath+0x12/0x71
[ 2382.270013] Code: 20 a0 48 c7 c6 e1 6d 20 a0 48 89 e5 41 54 53 4c 8d 65 d0 48 89 fb 48 83 ec 28 c7 45 d0 00 00 00 00 49 8d 7c 24 08 e8 7a 55 ed e0 <4c> 89 a3 40 05 00 00 48 89 df e8 eb fd ff ff 85 c0 75 1a 48 8d
[ 2382.270013] RIP  [<ffffffffa01fe616>] snd_card_free+0x36/0x70 [snd]
[ 2382.270013]  RSP <ffff88003c767ea0>
[ 2382.270013] CR2: 0000000000000540

Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

changeset 70433a15 ("media: videobuf2: Refactor vb2_fileio_data
and vb2_thread") broke videobuf2-dvb.

The root cause is that, instead of calling threadio->fnc() for
all types of events except for VB2_BUF_STATE_ERROR, it was calling
it only for VB2_BUF_STATE_DONE.

With that, the DVB thread were never called.

Cc: stable@vger.kernel.org # Kernel >= 4.3
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The vb2_thread implementation was made generic and was moved from
videobuf2-v4l2.c to videobuf2-core.c in commit af3bac1a. Unfortunately
that clearly was never tested since it broke read() causing NULL address
references.

The root cause was confused handling of vb2_buffer vs v4l2_buffer (the pb
pointer in various core functions).

The v4l2_buffer no longer exists after moving the code into the core and
it is no longer needed. However, the vb2_thread code passed a pointer to
a vb2_buffer to the core functions were a v4l2_buffer pointer was expected
and vb2_thread expected that the vb2_buffer fields would be filled in
correctly.

This is obviously wrong since v4l2_buffer != vb2_buffer. Note that the
pb pointer is a void pointer, so no type-checking took place.

This patch fixes this problem:

1) allow pb to be NULL for vb2_core_(d)qbuf. The vb2_thread code will use
   a NULL pointer here since they don't care about v4l2_buffer anyway.
2) let vb2_core_dqbuf pass back the index of the received buffer. This is
   all vb2_thread needs: this index is the index into the q->bufs array
   and vb2_thread just gets the vb2_buffer from there.
3) the fileio->b pointer (that originally contained a v4l2_buffer) is
   removed altogether since it is no longer needed.

Tested with vivid and the cobalt driver.

Cc: stable@vger.kernel.org # Kernel >= 4.3
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The tda1004x was updating the properties cache before locking.
If the device is not locked, the data at the registers are just
random values with no real meaning.

This caused the driver to fail with libdvbv5, as such library
calls GET_PROPERTY from time to time, in order to return the
DVB stats.

Tested with a saa7134 card 78:
	ASUSTeK P7131 Dual, vendor PCI ID: 1043:4862

Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This is a partial revert of commit ed8d1cf0 ("[media] Export I2C
module alias information in missing drivers") that exported the module
aliases for the I2C drivers that were missing to make autoload to work.

But there is a bug report [0] that auto load of the ir-kbd-i2c driver
cause the Hauppauge HD-PVR driver to not behave correctly.

This is a hdpvr latent bug that was just exposed by ir-kbd-i2c module
autoloading working and will also happen if the I2C driver is built-in
or a user calls modprobe to load the module and register the driver.

But there is a regression experimented by users so until the real bug
is fixed, let's not export the module alias for the ir-kbd-i2c driver
even when this just masks the actual issue.

[0]: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=810726

Fixes: ed8d1cf0 ("[media] Export I2C module alias information in missing drivers")

Cc: <stable@vger.kernel.org> # 4.3+
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>

With CONFIG_V4L2=m and VIDEO_SAMSUNG_EXYNOS4_IS=y, we can select the
individual drivers as built-in code when that should not be possible:

drivers/built-in.o: In function `s5pcsis_set_fmt':
policy.c:(.text+0x13afdc): undefined reference to `v4l_bound_align_image'
drivers/built-in.o: In function `s5pcsis_probe':
policy.c:(.text+0x13b440): undefined reference to `v4l2_of_parse_endpoint'
policy.c:(.text+0x13b72c): undefined reference to `v4l2_subdev_init'

Changing VIDEO_SAMSUNG_EXYNOS4_IS to tristate means that the dependency
from CONFIG_V4L2 propates to the individual Kconfig symbols and they
can only be built as loadable modules if V4L2 or any other of the
dependencies itself is a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The build of m32r allmodconfig fails with the error:
drivers/media/v4l2-core/videobuf2-dma-contig.c:484:2:
	error: implicit declaration of function 'dma_get_cache_alignment'

The build of videobuf2-dma-contig.c depends on HAS_DMA and it is
correctly mentioned in the Kconfig but the symbol VIDEO_STI_BDISP also
selects VIDEOBUF2_DMA_CONTIG, so it is trying to compile
videobuf2-dma-contig.c even though HAS_DMA is not defined.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Some user space use cases result in kernel hangup on the HIC_OPEN_SENSOR
command write. In case when a minimalistic application is used for setting
up the streaming, the hangups occur only occasionally. In case of GStreamer
use cases it is always the case.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

In order to allow for automatic media device entities linking
from the level of libv4l plugin the open system call shouldn't
fail, as the libv4l plugins can begin their job not until it
succeeds.
This patch allows for leaving the  pipeline not linked on
open and postpones verifying it to the moment when streamon
callback is called.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

VIDIOC_SUBDEV_G_FMT ioctl should return TRY format previously
set with VIDIOC_SUBDEV_S_FMT. Currently it is not the case as
only ACTIVE formats are saved in the driver. Since the driver
doesn't alter hardware state in the set_fmt op anyway, the
op can save the format in both TRY and ACTIVE case.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Ironically, 7d4020c3 ("[media] exynos4-is: fix some warnings when
compiling on arm64") fixed some format string bugs but introduced a
new one. buf_index is a simple int, so it should be printed with %d,
not %pad (which is correctly used for dma_addr_t).

Fixes: 7d4020c3 ("[media] exynos4-is: fix some warnings when compiling on arm64")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This was found with the -RT patch enabled, but the fix should apply to
non-RT also.

Compilation error without this fix:
../drivers/media/platform/vsp1/vsp1_video.c: In function
'vsp1_pipeline_stopped':
../drivers/media/platform/vsp1/vsp1_video.c:524:2: error: expected
expression before 'do'
  spin_unlock_irqrestore(&pipe->irqlock, flags);
    ^
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Correct the debug output message to show correct format.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

I got the following WARN on a simple unbind/bind cycle:

root@Lager:/sys/bus/i2c/drivers/adv7180# echo 6-0020 > unbind
root@Lager:/sys/bus/i2c/drivers/adv7180# echo 6-0020 > bind
[   31.097652] adv7180 6-0020: chip found @ 0x20 (e6520000.i2c)
[   31.123744] ------------[ cut here ]------------
[   31.128413] WARNING: CPU: 3 PID: 873 at drivers/media/platform/soc_camera/soc_camera.c:1463 soc_camera_async_bound+0x40/0xa0()
[   31.139896] CPU: 3 PID: 873 Comm: sh Not tainted 4.4.0-rc3-00062-ge8ae2c0b6bca2a #172
[   31.147815] Hardware name: Generic R8A7790 (Flattened Device Tree)
[   31.154056] Backtrace:
[   31.156575] [<c0014bc0>] (dump_backtrace) from [<c0014d80>] (show_stack+0x20/0x24)
[   31.164233]  r6:c05c5b33 r5:00000009 r4:00000000 r3:00404100
[   31.170017] [<c0014d60>] (show_stack) from [<c01e2344>] (dump_stack+0x78/0x94)
[   31.177344] [<c01e22cc>] (dump_stack) from [<c0029e7c>] (warn_slowpath_common+0x98/0xc4)
[   31.185518]  r4:00000000 r3:00000000
[   31.189172] [<c0029de4>] (warn_slowpath_common) from [<c0029fa0>] (warn_slowpath_null+0x2c/0x34)
[   31.198043]  r8:eb38df28 r7:eb38c5d0 r6:eb38de80 r5:e6962810 r4:eb38de80
[   31.204898] [<c0029f74>] (warn_slowpath_null) from [<c0356348>] (soc_camera_async_bound+0x40/0xa0)
[   31.213955] [<c0356308>] (soc_camera_async_bound) from [<c03499a0>] (v4l2_async_test_notify+0x9c/0x108)
[   31.223430]  r5:eb38c5ec r4:eb38de80
[   31.227084] [<c0349904>] (v4l2_async_test_notify) from [<c0349dd8>] (v4l2_async_register_subdev+0x88/0xd0)
[   31.236822]  r7:c07115c8 r6:c071160c r5:eb38c5ec r4:eb38de80
[   31.242622] [<c0349d50>] (v4l2_async_register_subdev) from [<c0337040>] (adv7180_probe+0x2c8/0x3a4)
[   31.251753]  r8:00000000 r7:00000001 r6:eb38de80 r5:ea973400 r4:eb38de10 r3:00000000
[   31.259660] [<c0336d78>] (adv7180_probe) from [<c032dd80>] (i2c_device_probe+0x1a0/0x1e4)

This gets fixed by clearing the control device pointer on async_unbind.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The Media Control framework now requires entities to be registered with
the media device before creating links so commit c7621b30 ("[media]
v4l: vsp1: separate links creation from entities init") separated link
creation from entities init.

But unfortunately that patch introduced a regression since wrong links
were created causing a boot failure on Renesas boards.

This patch fixes the boot issue and also the media graph was compared
by Geert Uytterhoeven to make sure that the driver changes required by
the Media Control framework next generation did not affect the graph.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.

  The executive summary:

   - ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
   - Avoid useless rebuilds for zboot.
   - jz4780: Add NEMC, BCH and NAND device tree nodes
   - Initial support for the MicroChip's DT platform.  As all the device
     drivers are missing this is still of limited use.
   - Some Loongson3 cleanups.
   - The unavoidable whitespace polishing.
   - Reduce clock skew when synchronizing the CPU cycle counters on CPU
     startup.
   - Add MIPS R6 fixes.
   - Lots of cleanups across arch/mips as fallout from KVM.
   - Lots of minor fixes and changes for IEEE 754-2008 support to the
     FPU emulator / fp-assist software.
   - Minor Ralink, BCM47xx and bcm963xx platform support improvments.
   - Support SMP on BCM63168"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
  MIPS: zboot: Add support for serial debug using the PROM
  MIPS: zboot: Avoid useless rebuilds
  MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
  MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
  MIPS: bcm963xx: Update bcm_tag field image_sequence
  MIPS: bcm963xx: Move extended flash address to bcm_tag header file
  MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
  MIPS: bcm63xx: nvram: Use nvram structure definition from header file
  MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
  MAINTAINERS: Add KVM for MIPS entry
  MIPS: KVM: Add missing newline to kvm_err()
  MIPS: Move KVM specific opcodes into asm/inst.h
  MIPS: KVM: Use cacheops.h definitions
  MIPS: Break down cacheops.h definitions
  MIPS: Use EXCCODE_ constants with set_except_vector()
  MIPS: Update trap codes
  MIPS: Move Cause.ExcCode trap codes to mipsregs.h
  MIPS: KVM: Make kvm_mips_{init,exit}() static
  MIPS: KVM: Refactor added offsetof()s
  MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
  ...

Merge tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform driver updates from Darren Hart:
 "Emergency travel prevented me from completing my final testing on this
  until today.  Nothing here that couldn't wait until RC1 fixes, but I
  thought it best to get it out sooner rather than later as it does
  contain a build warning fix.

  Summary:

  A build warning fix, MAINTAINERS cleanup, and a new DMI quirk:

  ideapad-laptop:
   - Add Lenovo Yoga 700 to no_hw_rfkill dmi list

  MAINTAINERS:
   - Combine multiple telemetry entries

  intel_telemetry_debugfs:
   - Fix unused warnings in telemetry debugfs"

* tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
  MAINTAINERS: Combine multiple telemetry entries
  intel_telemetry_debugfs: Fix unused warnings in telemetry debugfs

Pull thermal management updates from Zhang Rui:
 "The top merge commit was re-generated yesterday because two topic
  branches were dropped from this pull request in the last minute due to
  some unaddressed comments.  All the other material has been in
  linux-next for quite a while.

  Specifics:

   - Enhance thermal core to handle unexpected device cooling states
     after fresh boot and system resume.  From Zhang Rui and Chen Yu.

   - Several fixes and cleanups on Rockchip and RCAR thermal drivers.
     From Caesar Wang and Kuninori Morimoto.

   - Add Broxton support for Intel processor thermal reporting device
     driver.  From Amy Wiles"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: trip_point_temp_store() calls thermal_zone_device_update()
  thermal: rcar: rcar_thermal_get_temp() return error if strange temp
  thermal: rcar: check irq possibility in rcar_thermal_irq_xxx()
  thermal: rcar: check every rcar_thermal_update_temp() return value
  thermal: rcar: move rcar_thermal_dt_ids to upside
  thermal: rockchip: Support the RK3399 SoCs in thermal driver
  thermal: rockchip: Support the RK3228 SoCs in thermal driver
  dt-bindings: rockchip-thermal: Support the RK3228/RK3399 SoCs compatible
  thermal: rockchip: fix a trivial typo
  Thermal: Enable Broxton SoC thermal reporting device
  thermal: constify pch_dev_ops structure
  Thermal: do thermal zone update after a cooling device registered
  Thermal: handle thermal zone device properly during system sleep
  Thermal: initialize thermal zone device correctly

Pull 9p updates from Eric Van Hensbergen:
 "Sorry for the last minute pull request, there's was a change that
  didn't get pulled into for-next until two weeks ago and I wanted to
  give it some bake time.

  Summary:

  Rework and error handling fixes, primarily in the fscatch and fd
  transports"

* tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  fs/9p: use fscache mutex rather than spinlock
  9p: trans_fd, bail out if recv fcall if missing
  9p: trans_fd, read rework to use p9_parse_header
  net/9p: Add device name details on error

Pull Ceph updates from Sage Weil:
 "The two main changes are aio support in CephFS, and a series that
  fixes several issues in the authentication key timeout/renewal code.

  On top of that are a variety of cleanups and minor bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: remove outdated comment
  libceph: kill off ceph_x_ticket_handler::validity
  libceph: invalidate AUTH in addition to a service ticket
  libceph: fix authorizer invalidation, take 2
  libceph: clear messenger auth_retry flag if we fault
  libceph: fix ceph_msg_revoke()
  libceph: use list_for_each_entry_safe
  ceph: use i_size_{read,write} to get/set i_size
  ceph: re-send AIO write request when getting -EOLDSNAP error
  ceph: Asynchronous IO support
  ceph: Avoid to propagate the invalid page point
  ceph: fix double page_unlock() in page_mkwrite()
  rbd: delete an unnecessary check before rbd_dev_destroy()
  libceph: use list_next_entry instead of list_entry_next
  ceph: ceph_frag_contains_value can be boolean
  ceph: remove unused functions in ceph_frag.h

Pull SMB3 fixes from Steve French:
 "A collection of CIFS/SMB3 fixes.

  It includes a couple bug fixes, a few for improved debugging of
  cifs.ko and some improvements to the way cifs does key generation.

  I do have some additional bug fixes I expect in the next week or two
  (to address a problem found by xfstest, and some fixes for SMB3.11
  dialect, and a couple patches that just came in yesterday that I am
  reviewing)"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cifs_dbg() outputs an uninitialized buffer in cifs_readdir()
  cifs: fix race between call_async() and reconnect()
  Prepare for encryption support (first part). Add decryption and encryption key generation. Thanks to Metze for helping with this.
  cifs: Allow using O_DIRECT with cache=loose
  cifs: Make echo interval tunable
  cifs: Check uniqueid for SMB2+ and return -ESTALE if necessary
  Print IP address of unresponsive server
  cifs: Ratelimit kernel log messages

Like the Yoga 900 models the Lenovo Yoga 700 does not have a
hw rfkill switch, and trying to read the hw rfkill switch through the
ideapad module causes it to always reported blocking breaking wifi.

This commit adds the Lenovo Yoga 700 to the no_hw_rfkill dmi list, fixing
the wifi breakage.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1295272
Tested-by: <dinyar.rabady+spam@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch combines all the telemetry file entries in MAINTAINERS via
wildcard.
Signed-off-by: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch fixes compile time warnings when CONFIG_PM_SLEEP
is undefined. In this case sleep related counters are unused.
Signed-off-by: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

If we detect that there is nothing to do just set the flag and do not
check if it was already set before.  Races really do not matter.  If the
flag is set by any code then the shepherd will start dealing with the
situation and reenable the vmstat workers when necessary again.

Since commit 0eb77e98 ("vmstat: make vmstat_updater deferrable again
and shut down on idle") quiet_vmstat might update cpu_stat_off and mark
a particular cpu to be handled by vmstat_shepherd.  This might trigger a
VM_BUG_ON in vmstat_update because the work item might have been
sleeping during the idle period and see the cpu_stat_off updated after
the wake up.  The VM_BUG_ON is therefore misleading and no more
appropriate.  Moreover it doesn't really suite any protection from real
bugs because vmstat_shepherd will simply reschedule the vmstat_work
anytime it sees a particular cpu set or vmstat_update would do the same
from the worker context directly.  Even when the two would race the
result wouldn't be incorrect as the counters update is fully idempotent.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As most platforms implement the PROM serial interface prom_putchar()
add a simple bridge to allow re-using this code for zboot.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11811/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add dummy.o to the targets list, and fill targets automatically from
$(vmlinuzobjs) to avoid having to maintain two lists.

When building with XZ compression copy ashldi3.c to the build
directory to use a different object file for the kernel and zboot.
Without this the same object file need to be build with different
flags which cause a rebuild at every run.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11810/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Allow BMIPS_GENERIC supported platforms to build GPIO controller
drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Dragan Stancevic <dragan.stancevic@gmail.com>
Cc: cernekee@gmail.com
Cc: jaedon.shin@gmail.com
Cc: gregory.0xf0@gmail.com
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12019/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Remove bcm63xx_nvram_get_psi_size() as it now has no users.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11836/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The "dual_image" and "inactive_flag" fields should be merged into a single
"image_sequence" field.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11834/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The extended flash address needs to be subtracted from bcm_tag flash
image offsets. Move this value to the bcm_tag header file.

Renamed define name to consistently use bcm963xx for flash layout
which should be considered a property of the board and not the SoC
(i.e. bcm63xx could theoretically be used on a board without CFE
or any flash).
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11833/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Move Broadcom BCM963xx image tag data structure to include/linux/
so that drivers outside of mach-bcm63xx can use it.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11832/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>