- 15 May, 2012 21 commits
-
-
Franky Lin authored
The new brcmf_sdio_regrl/regwl interface has already performed retries on failed attempts. It is no longer necessary to have the retry mechanism in r_sdreg32/w_sdreg32. Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
Franky Lin <frankyl@broadcom.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Franky Lin authored
Use the newly introduced brcmf_sdio_regwl to replace brcmf_sdcard_reg_write as part of the SDIO WiFi dongle register access interface clean up. Reviewed-by:
-
Franky Lin authored
Use the newly introduced brcmf_sdio_regrl to replace brcmf_sdcard_reg_read as part of the SDIO WiFi dongle register access interface clean up. Reviewed-by:
-
Franky Lin authored
Use the newly introduced brcmf_sdio_regwb to replace brcmf_sdcard_cfg_write as part of the SDIO WiFi dongle register access interface clean up. Reviewed-by:
-
Franky Lin authored
Use the newly introduced brcmf_sdio_regrb to replace brcmf_sdcard_cfg_read as part of the SDIO WiFi dongle register access interface clean up. Reviewed-by:
-
Franky Lin authored
Both brcmf_sdcard_cfg_read/write and brcmf_sdcard_reg_read/write are used as interface functions for register access of SDIO WiFi dongle. A unified interface brcmf_sdio_regr/w is introduced in this patch in order to simplify the interface and keep the complexity within the lower layer. Reviewed-by:
-
Franky Lin authored
brcmf_sdcard_set_sbaddr_window configures 3 registers on SDIO function misc bank to change current silicon backplane programming window. This patch makes it call brcmf_sdioh_request_byte directly in order to prepare for the write register interface unification. Reviewed-by:
-
Franky Lin authored
The size parameter for brcmf_sdcard_reg_write is always 4. Remove it to make the code cleaner. Reviewed-by:
-
Franky Lin authored
The size parameter for brcmf_sdcard_reg_read is always 4. Remove it to make the code neat. Reviewed-by:
-
Sujith Manoharan authored
This patch fixes multiple issues with the current RTT implementation in ath9k. * The data that is obtained from the RTT interface registers are stored in 31:5 - mask out the extra bits when reading them. * A history buffer is maintained which is not needed at all. Remove this array and just store the baseband data for each chain (or bank). * A 'num_readings' variable was being used to handle the last entry. But it was being used in an improper manner, with the result that the RTT values were never being written to the RTT Interface registers. Fix this by using a simple flag. * Stop baseband operations before programming the calibration values to the HW. * Do not restore RX gain settings as part of RTT. Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Chun-Yeow Yeoh authored
Forwarded PREQ is either unicast or multicast. The appropriate counters should be incremented accordingly. Signed-off-by:
Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by:
-
Thomas Pedersen authored
Only send a cfg80211 new peer candidate notification if userspace has yet to allocate this station entry. Signed-off-by:
Thomas Pedersen <thomas@cozybit.com> Signed-off-by:
-
Emmanuel Grumbach authored
If the BA session is torn down before we had a chance to start it we shouldn't disable the AGG tx queues that weren't enabled. This can happen in two cases: 1) We get a delBA before we drained our Tx queues in agg start flow 2) We didn't get the (successfull) addBA response on time Reported-by:
Daniel Chyan <dchyan@princeton.edu> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
We have TX_REPLY for that. Signed-off-by:
-
Amit Beka authored
The power index that the user gives as module parameter in in range 1-5, but we need to decrease it in order to create an array index out of it (0-4) for the power table command. Signed-off-by:
Amit Beka <amit.beka@intel.com> Signed-off-by:
-
Wey-Yi Guy authored
Once driver decide to change reduced tx power behavior, make sure the reduce tx power valid bit is set Change-Id: I3afae96319292d8cb347a812a948085c5db7ad91 Signed-off-by:
-
Wey-Yi Guy authored
Change-Id: Ia6294d651dcffdcaf8b62e67bcef52bd8c158dea Signed-off-by:
-
Wey-Yi Guy authored
In bt coex, consider the average rssi as part of decision making process Change-Id: I8d11d7f177a6875e2a9d08f7539d42253226fd7a Signed-off-by:
-
Marcel Holtmann authored
The SHDLC link layer of HCI based drivers uses CRC-CCITT and thus needs to select that kernel option. Otherwise it ends up with this linking error: net/built-in.o: In function `nfc_shdlc_add_len_crc': net/nfc/hci/shdlc.c:113: undefined reference to `crc_ccitt' Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Acked-by:
Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
-
Bing Zhao authored
Documentation/CodingStyle says "Do not unnecessarily use braces where a single statement will do." Use "switch/case", instead of "if/else_if/else", so that more cases can be added later. Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
Avinash Patil <patila@marvell.com> Signed-off-by:
-
Javier Cardona authored
Drivers need to report the number of transmission attempts for each rate as well as to terminate the rate array with -1. The in-kernel datapath of hwsim simulates a perfect medium, therefore the driver only needs to report that the first transmission attempt was sucessfully completed at the most favorable rate. Rate control is working again for this driver. Tested mesh mode with minstrel. Signed-off-by:
Javier Cardona <javier@cozybit.com> Signed-off-by:
-
- 09 May, 2012 19 commits
-
-
John W. Linville authored
Signed-off-by: -
Ashok Nagarajan authored
This patch introduces a new mesh configuration parameter "ht_opmode" and will allow user to check the current HT protection mode selected. Users could configure the protection mode by the command "iw mesh_iface set mesh_param mesh_ht_protection_mode=2". The default protection mode of mesh is set to non-HT mixed mode. Signed-off-by:
Ashok Nagarajan <ashok@cozybit.com> Reviewed-by:
-
Ashok Nagarajan authored
Now that we have protection enabled, allow non-HT and HT20 stations to peer with HT40+/- stations. Peering is still disallowed for HT40+/- mismatch. Signed-off-by:
-
Ashok Nagarajan authored
Section 9.23.3.5 of IEEE 80211s standard describes the protection rules for HT mesh STA in a MBSS. Three HT protection modes are supported for now: non-HT mixed mode - is selected if any non-HT peers are present in our MBSS. 20MHz-protection mode - is selected if all peers in our 20/40MHz MBSS support HT and atleast one HT20 peer is present. no-protection mode - is selected otherwise. This is a limited implementation of 9.23.3.5, which only considers mesh peers when determining the HT protection mode. Station's channel_type needs to be maintained. Signed-off-by:
-
Ashok Nagarajan authored
Signed-off-by:
-
Emmanuel Grumbach authored
Since the BSS table is organized in a RB tree, the BSSs need to be comparable. This means that we must define a < and > operator to the BSS object. compare_ethr_addr isn't enough since it returns only a binary value. Since Felix's cfg80211: use compare_ether_addr on MAC addresses instead of memcmp Because of the constant size and guaranteed 16 bit alignment, the inline compare_ether_addr function is much cheaper than calling memcmp. Signed-off-by:Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Franky Lin authored
Some sdio host controllers do not support real in band interrupt. Software polling mode as a replacement is not fast enough for high throughput and new features. Also some in band interrupts do not support host wake up on embedded platform even when they are real physical interrupts. Therefore out of band (oob) interrupt mechanism is implemented for these scenarios. To provide oob irq number and flags used for irq registration in brcmfmac, a platform device contains irq resource must be registered in board specific code. Here is an example of platform device structure: struct resource brcmf_sdio_res[] = { { .start = GPIO_BRCMF_SDIO_OOB_NUM, .end = GPIO_BRCMF_SDIO_OOB_NUM, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, } }; struct platform_device brcmf_sdio_device = { .name = "brcmf_sdio_pd", .id = -1, .num_resources = ARRAY_SIZE(brcmf_sdio_res), .resource = brcmf_sdio_res, }; Reviewed-by: -
Franky Lin authored
For out of band interrupt which is going to be introduced shortly, the interrupt register function must be called after firmware is downloaded. This patch moves it from brcmf_sdbrcm_probe to brcmf_sdbrcm_bus_init. Reviewed-by:
-
Franky Lin authored
Bus state should be the correct flag for bus status. Use it instead of result from previous function call for backplane clock switch. Reviewed-by:
-
Franky Lin authored
brcmf_sdbrcm_isr doesn't access to the dongle through SDIO bus. Stop releasing and claiming host in irq handler to eliminate any potential risk. Reviewed-by:
-
Ben Greear authored
The signal and noise are forced to be positive since ethtool deals in unsigned 64-bit values and this number should be human readable. This gives easy access to some of the data formerly exposed in the deprecated /proc/net/wireless file. Signed-off-by:
Ben Greear <greearb@candelatech.com> Signed-off-by:
-
Ben Greear authored
This adds hooks to call into the driver to get additional stats for the ethtool API. Signed-off-by:
-
Ben Greear authored
This lets ethtool print out stats related to stations connected to the interface. Does not yet get stats from the underlying driver. Signed-off-by:
-
Ben Greear authored
Signed-off-by:
-
Wey-Yi Guy authored
"iwlwifi: use correct released ucode version" change the ucode api ok from 6000G2 to 6000G2B, but it shall belong to 6030 device series, not the 6005 device series. Fix it Cc: stable@vger.kernel.org #3.3+ Signed-off-by:
-
Meenakshi Venkataraman authored
Report correctly the latest released version of the iwlwifi firmware for all iwlwifi-supported devices. Cc: stable@vger.kernel.org #3.3+ Signed-off-by:
Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Signed-off-by:
-
Ben Hutchings authored
Currently cfg80211 fails to create a "phy80211" symlink in sysfs from the net device to the wiphy device. The latter needs to be registered first. Compile-tested only. Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Ben Hutchings authored
Currently cfg80211 fails to create a "phy80211" symlink in sysfs from the net device to the wiphy device. The latter needs to be registered first. Compile-tested only. Reported-by:
Cesare Leonardi <celeonar@gmail.com> Signed-off-by:
-
Anisse Astier authored
RFCSR is only used in rt2800. For other chipsets, the debug struct for rfcsr should be zeroed, which isn't be an issue, since the code can now cope with that. Signed-off-by:
Anisse Astier <anisse@astier.eu> Acked-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
