Speedup and shrink GPIO irq handling code, by using a pointer
that's available in the irq_chip structure instead of calling
the get_gpio_bank() function.  On OMAP1 this saves 44 words,
most of which were in IRQ critical path methods.  Hey, every
few instructions help.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch adds minimal OMAP2430 support to plat-omap files to
get the kernel booting on 2430SDP.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

More GPIO/IRQ cleanup:

  - compile-time removal of much useless code
      * mpuio support on non-OMAP1.
      * 15xx/730/24xx gpio support on 1610
      * 15xx/730/16xx gpio support on 24xx
      * etc

  - remove all BUG() calls, which are always bad news ... replaced some
    with normal fault reports for that call, others with WARN_ON(1).

  - small mpuio bugfix:  add missing set_type() method

Oh, and fix a minor merge issue: inode->u.generic_ip is now gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add some GPIO debug support:  /sys/kernel/debug/omap_gpio dumps the state
of all GPIOs that have been claimed, including basic IRQ info if relevant.
Tested on 24xx, 16xx.

Includes minor bugfixes:  recording IRQ trigger mode (this should probably
be a genirq patch), adding missing space to non-wakeup warning
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Some GPIOs on OMAP2420 do not have wakeup capabilities. If these GPIOs
are configured as IRQ sources, spurious interrupts will be generated
each time the core domain enters retention.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Enable 24xx GPIO autoidling
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Lots of places in arch/arm were needlessly including linux/ptrace.h,
resumably because we used to pass a struct pt_regs to interrupt
handlers.  Now that we don't, all these ptrace.h includes are
redundant.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This reverts commit 60cba200.  It's been
linked to lockups of the e1000 hardware, see for example

	https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=229603

but it's likely that the commit itself is not really introducing the
bug, but just allowing an unrelated problem to rear its ugly head (ie
one current working theory is that the code exposes us to a hardware
race condition by decreasing the amount of time we spend in each NAPI
poll cycle).

We'll revert it until root cause is known.  Intel has a repeatable
reproduction on two different machines and bus traces of the hardware
doing something bad.
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Greg KH <gregkh@suse.de>
Cc: Dave Jones <davej@redhat.com>
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  pata_sis: Fix oops on boot

A small number of SiS setups require special handling (not many judging
by how long this dumb bug survived). A couple of Fedora 7 devel testers
hit an Oops on pata_sis loading which is caused by terminal confusion
between chipset as 'the chipset we have found' and chipset as 'array
iterator'
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The Yukon FE (100mbit only) chips do not support large packets.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The Yukon EC Ultra chips have transmit settings for store and
forward and PCI buffering. By setting these appropriately, normal
performance goes from 750Mbytes/sec to 940Mbytes/sec (non-jumbo).

It is also possible to do Jumbo mode, but it means turning off
TSO and checksum offload so the performance gets worse. There isn't
enough buffering for checksum offload to work.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Need to make sure and disable ASF on all chip types. Otherwise, there may be
random reboots.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

There should never be descriptor error unless hardware or driver is buggy.
But if an error occurs, print useful information, clear irq, and recover.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This device is having all sorts of problems that lead to data corruption
and system instability.  It gets receive status and data out of order,
it generates descriptor and TSO errors, etc.

Until the problems are resolved, it should not be used by anyone
who cares about there system.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Gianfar needs crc32 to be selected to compile.
Signed-off-by: Dave Jiang <djiang@mvista.com>

--
 drivers/net/Kconfig |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)
--
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The basic structure of "normal" UDP/IP/Ethernet
frames (that actually work):
 - It starts with the Ethernet header (dest MAC, src MAC, etc.)
 - The next part is occupied by the IP header (version info, length of
packet, id=0, fragment offset=0, checksum, from / to address, etc.)
 - Then comes the UDP header (src / dest port, length, checksum)
 - Actual payload
 - Ethernet checksum

Now what's different for IP fragment:
 - The IP header has id set to some value (same for all fragments),
offset is set appropriately (i.e. 0 for first fragment, following
according to size of other fragments), size is the length of the frame.
 - UDP header is unchanged. I.e. length is according to full UDP
datagram, not just the part within the actual frame! But this is only
true within the first frame: all following frames don't have a valid
UDP-header at all.

The spidernet silicon seems to be quite intelligent: It's able to
compute (IP / UDP / Ethernet) checksums on the fly and tests if frames
are conforming to RFC -- at least conforming to RFC on complete frames.

But IP fragments are different as explained above:
I.e. for IP fragments containing part of a UDP datagram it sees
incompatible length in the headers for IP and UDP in the first frame
and, thus, skips this frame. But the content *is* correct for IP
fragments. For all following frames it finds (most probably) no valid
UDP header at all. But this *is* also correct for IP fragments.

The Linux IP-stack seems to be clever in this point. It expects the
spidernet to calculate the checksum (since the module claims to be able
to do so) and marks the skb's for "normal" frames accordingly
(ip_summed set to CHECKSUM_HW).
But for the IP fragments it does not expect the driver to be capable to
handle the frames appropriately. Thus all checksums are allready
computed. This is also flaged within the skb (ip_summed set to
CHECKSUM_NONE).

Unfortunately the spidernet driver ignores that hints. It tries to send
the IP fragments of UDP datagrams as normal UDP/IP frames. Since they
have different structure the silicon detects them the be not
"well-formed" and skips them.

The following one-liner against 2.6.21-rc2 changes this behavior. If the
IP-stack claims to have done the checksumming, the driver should not
try to checksum (and analyze) the frame but send it as is.
Signed-off-by: Norbert Eicker <n.eicker@fz-juelich.de>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Remove assumption that PHY interrupts use GPIOs 3 and 5.
Deal with PHY interrupts connected to any GPIO pins.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Reuse the incoming skb when a clientless abort req is recieved.

The release of RDMA connections HW resources might be deferred in
low memory situations.
Ensure that no further activity is passed up to the RDMA driver
for these connections.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
  KVM: Fix off-by-one when writing to a nonpae guest pde

Nonpae guest pdes are shadowed by two pae ptes, so we double the offset
twice: once to account for the pte size difference, and once because we
need to shadow pdes for a single guest pde.

But when writing to the upper guest pde we also need to truncate the
lower bits, otherwise the multiply shifts these bits into the pde index
and causes an access to the wrong shadow pde.  If we're at the end of the
page (accessing the very last guest pde) we can even overflow into the
next host page and oops.
Signed-off-by: Avi Kivity <avi@qumranet.com>

There is a race between netlink_dump_start() and netlink_release()
that can lead to the situation when a netlink socket with non-zero
callback is freed.

Here it is:

CPU1:                           CPU2
netlink_release():              netlink_dump_start():

                                sk = netlink_lookup(); /* OK */

netlink_remove();

spin_lock(&nlk->cb_lock);
if (nlk->cb) { /* false */
  ...
}
spin_unlock(&nlk->cb_lock);

                                spin_lock(&nlk->cb_lock);
                                if (nlk->cb) { /* false */
                                         ...
                                }
                                nlk->cb = cb;
                                spin_unlock(&nlk->cb_lock);
                                ...
sock_orphan(sk);
/*
 * proceed with releasing
 * the socket
 */

The proposal it to make sock_orphan before detaching the callback
in netlink_release() and to check for the sock to be SOCK_DEAD in
netlink_dump_start() before setting a new callback.
Signed-off-by: Denis Lunev <den@openvz.org>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes an oops first reported in mid 2006 - see
http://lkml.org/lkml/2006/8/29/358 The cause of this bug report is that
when an error is signalled on the socket, irda_recvmsg_stream returns
without removing a local wait_queue variable from the socket's sk_sleep
queue. This causes havoc further down the road.

In response to this problem, a patch was made that invoked sock_orphan on
the socket when receiving a disconnect indication. This is not a good fix,
as this sets sk_sleep to NULL, causing applications sleeping in recvmsg
(and other places) to oops.

This is against the latest net-2.6 and should be considered for -stable
inclusion. 
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The way partial delivery is currently implemnted, it is possible to
intereleave a message (either from another steram, or unordered) that
is not part of partial delivery process.  The only way to this is for
a message to not be a fragment and be 'in order' or unorderd for a
given stream.  This will result in bypassing the reassembly/ordering
queues where things live duing partial delivery, and the
message will be delivered to the socket in the middle of partial delivery.

This is a two-fold problem, in that:
1.  the app now must check the stream-id and flags which it may not
be doing.
2.  this clearing partial delivery state from the association and results
in ulp hanging.

This patch is a band-aid over a much bigger problem in that we
don't do stream interleave.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure to actually assign the determined mode to
rq->sadb_x_ipsecrequest_mode.

Noticed by Joe Perches.
Signed-off-by: David S. Miller <davem@davemloft.net>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [BRIDGE]: Unaligned access when comparing ethernet addresses
  [SCTP]: Unmap v4mapped addresses during SCTP_BINDX_REM_ADDR operation.
  [SCTP]: Fix assertion (!atomic_read(&sk->sk_rmem_alloc)) failed message
  [NET]: Set a separate lockdep class for neighbour table's proxy_queue
  [NET]: Fix UDP checksum issue in net poll mode.
  [KEY]: Fix conversion between IPSEC_MODE_xxx and XFRM_MODE_xxx.
  [NET]: Get rid of alloc_skb_from_cache

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
  IB/mthca: Fix data corruption after FMR unmap on Sinai

* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
  [PATCH] x86: Fix potential overflow in perfctr reservation
  [PATCH] x86: Fix gcc 4.2 _proxy_pda workaround

* Last write during i2c_xfer is of the wrong byte (off-by-1).
* Read length is wrong for some of the reads (mistakenly used the PEC
  version)
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Looks like a local change I made to be able to test-compile the i2c-pasemi
driver leaked upstream.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Users have been complaining about the w83627ehf driver flooding their logs
with debug messages like:

w83627ehf 9191-0a10: Increasing fan 4 clock divider from 64 to 128

or:

w83627ehf 9191-0290: Increasing fan 4 clock divider from 4 to 8

The reason is that we failed to actually write the LSB of the encoded clock
divider value for that fan, causing the next read to report the same old value
again and again.

Additionally, the fan number was improperly reported, making the bug harder to
find.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Provide an dummy implementation of devm_ioport_map() and
devm_ioport_unmap() to allow drivers (eg, pata_platform) to build for
platforms where CONFIG_NO_IOPORT is selected.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sk_info_authunix is not being protected properly so the object that it
points to can be cache_put twice, leading to corruption.

We borrow svsk->sk_defer_lock to provide the protection.  We should
probably rename that lock to have a more generic name - later.

Thanks to Gabriel for reporting this.

Cc: Greg Banks <gnb@melbourne.sgi.com>
Cc: Gabriel Barazer <gabriel@oxeva.fr>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It got its lock and unlock backwards.

Fixes http://bugzilla.kernel.org/show_bug.cgi?id=8334

(obviously, this code could be using plain old spin_lock_irq(), too)

Cc: <matthias.kaehlcke@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch should fix or partly fix this bug:
http://bugzilla.kernel.org/show_bug.cgi?id=8276

The problem is:

- if we see "zero link case" during reading inode operation, we call
  ufs_error(which remount fs readonly), but not "mark" inode as bad (1)

- in readonly case we do not fill some data structures, which are used in
  read and write case (2)

- VFS call ufs_delete_inode if link count is zero (3)

so (1)->(3)->(2) cause oops, this patch should fix such scenario
Signed-off-by: Evgeniy Dushistov <dushistov@mail.ru>
Cc: Jim Paris <jim@jtan.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>