Convert the ucb1x00-core driver to use dev_pm_ops rather than the legacy
members in the mcp driver.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Issue a warning if the mcp clock was left enabled by some driver when
we're suspending or tearing down the core driver for the device.  This
is an aid for debugging missing disable calls.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The ucb1x00-core was leaving the mcp clock enabled indefinitely after
probe.  This needlessly wastes power.  Add the necessary disables to
ensure that the clock remains off when we don't need it.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

ucb1x00_enable() and ucb1x00_disable() are used for power saving on the
SIB interface, allowing the host supplied clock to be disabled when not
required.  We require drivers which access the ucb1x00 to ensure that
they have enabled the clock prior to accessing the device, and they
should disable it once they're done.

As we don't expect gpiolib users to be aware of this detail, we must
make these calls in the gpiolib interfaces.  Add them.

Also add them to the resume method, which needs to re-establish the
GPIO pin settings.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Cosmetic patch to scan the list of drivers in the order that the drivers
are registered, rather than the reverse order.  This avoids surprises
when drivers get probed in the reverse order, and input devices get
registered in a different order due to bind/unbind than from boot.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Register the gpio device with proper .owner and .dev elements set
appropraitely.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Clean up the device handling so we can use the struct device sanely.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Convert the ucb1x00 driver to use mutexes rather than the depreciated
semaphores for exclusive access to the ADC.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add a .owner initializer to the UCB1x00 mcp driver structure, and
set an appropriate module alias to identify this driver.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Provide a way to handle the software controlled ucb1x00 reset signal
from the ucb1x00-core driver without having to code platform specifics
into these drivers.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Nothing in this driver requires anything from the machine/platform
headers, so remove this needless header file.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Provide the input layer struct device with its parent device, so
that the input layer's device appears in the correct place in the
device tree.  This also allows the input device to be visibily
associated with its hardware.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch taken from 5dd7bf59 (ARM: sa11x0: Implement autoloading of codec
and codec pdata for mcp bus.) by Jochen Friedrich <jochen@scram.de>.

This adds just the codec data part of the patch.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The genirq code requires early access to interrupt controllers.  In
order to allow this, we need to resume the MCP via the _noirq methods
instead of the standard methods.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Convert the sa11x0 MCP driver to use dev_pm_ops rather than the legacy
members in the platform driver.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch taken from af9081ae (ARM: sa1100: Refactor mcp-sa11x0 to use
platform resources.) by Jochen Friedrich <jochen@scram.de>, and fixes
applied.

We can safely do this now that we have sanitized host removal; the
original patch had use-after-free bugs in the removal code.  Not only
that, but there was no checking of the ioremap() return.

The final change over Jochen's patch is that we wrap the base pointer
selection inside the various register indexes, which reduces the
possibility of the wrong register index being used.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch partly taken from af9081ae (ARM: sa1100: Refactor mcp-sa11x0 to
use platform resources.) by Jochen Friedrich <jochen@scram.de>

Move the MODULE_ALIAS() alongside the other MODULE_* definitions, and
use DRIVER_NAME to ensure that the driver is consistently named.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch taken from af9081ae (ARM: sa1100: Refactor mcp-sa11x0 to use
platform resources.) by Jochen Friedrich <jochen@scram.de>, and
consolidated to use a common function.

Move the setup of the PPC unit out of mcp-sa11x0 into the core SA11x0
code, and call it from each platforms initialization file.  This
centralizes the setup of the PPC unit while not polluting the mcp-sa11x0
driver with these details.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The dma_device_t variables are only ever written to by mcp-sa11x0 and
never read.  As the old SA11x0 DMA support will be removed, remove
these so that it no longer depends on the old SA11x0 DMA definitions.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

host_unregister() gives us no chance between removing the device
and the mcp data structure being freed to access the data inbetween,
which drivers may need to do if they need to iounmap() pointers in
their private data structures.

Therefore, re-jig the interfaces, which are now, on creation:

	mcp = mcp_host_alloc()
	if (mcp) {
		ret = mcp_host_add(mcp, data);

		if (!ret)
			mcp_host_free(mcp);
	}

and on removal:

	mcp_host_del(mcp);
	... access mcp ...
	mcp_host_free(mcp);

The free does the final put_device() on the struct device as one would
expect.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

If the ucb1x00 touchscreen is resumed while the touchscreen is being
touched, the main thread stops responding.  This occurs because two
things happen:

1. When we suspended, we were woken up, and executed the loop.
   Finding that the touchscreen was not pressed, we prepare to
   schedule for a maximum timeout, before being stopped in
   try_to_freeze().

2. an irq occurs, we disable the irq, and mark it as disabled,
   and wake the thread.  This wake occurs while the thread is
   still within __refrigerator()

3. The thread is unfrozen, and __refrigerator() sets the threads
   state back to INTERRUPTIBLE.

We then drop into schedule_timeout() with an infinite timeout and the
IRQ disabled.  This prevents any further screen touches activating
the thread.

Fix this by using kthread_freezable_should_stop() which handles the
freezing issues for us outside of the hotspot where the task state
matters.  Include a flag to ignore the touchscreen until it is
released to avoid sending unintended data to the application.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

gpiolib drivers should first set the output data before setting the
direction to avoid putting glitches on an output signal.  As an
additional bonus, we tweak the code to avoid unnecessary register
writes to the output and direction registers if they have no need
to be updated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We were not restoring the UCB1x00 gpio output data on resume, resulting
in incorrect GPIO output data after a resume.  Add the missing register
write.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

mcp_priv() does unexpected things when passed a void pointer.  Make it
a typed inline function, which ensures that it works correctly in
these cases.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The genirq layer complains if an interrupt handler returns with
interrupts enabled.  The UCB1x00 handler does just this, because
ucb1x00_enable() calls mcp_enable(), which uses spin_lock_irq()
rather than spin_lock_irqsave().  Convert this, and the divisor
setting functions to use spin_lock_irqsave().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This reverts commit 5dd7bf59.

Conflicts:

	scripts/mod/file2alias.c

This change is wrong on many levels.  First and foremost, it causes a
regression.  On boot on Assabet, which this patch gives a codec id of
'ucb1x00', it gives:

	ucb1x00 ID not found: 1005

0x1005 is a valid ID for the UCB1300 device.

Secondly, this patch is way over the top in terms of complexity.  The
only device which has been seen to be connected with this MCP code is
the UCB1x00 (UCB1200, UCB1300 etc) devices, and they all use the same
driver.  Adding a match table, requiring the codec string to match the
hardware ID read out of the ID register, etc is completely over the top
when we can just read the hardware ID register.

This reverts commit af9081ae.

This revert is necessary to revert 5dd7bf59.

Merge branches 'sched-urgent-for-linus', 'perf-urgent-for-linus' and 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/accounting, proc: Fix /proc/stat interrupts sum

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tracepoints/module: Fix disabling tracepoints with taint CRAP or OOT
  x86/kprobes: Add arch/x86/tools/insn_sanity to .gitignore
  x86/kprobes: Fix typo transferred from Intel manual

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, syscall: Need __ARCH_WANT_SYS_IPC for 32 bits
  x86, tsc: Fix SMI induced variation in quick_pit_calibrate()
  x86, opcode: ANDN and Group 17 in x86-opcode-map.txt
  x86/kconfig: Move the ZONE_DMA entry under a menu
  x86/UV2: Add accounting for BAU strong nacks
  x86/UV2: Ack BAU interrupt earlier
  x86/UV2: Remove stale no-resources test for UV2 BAU
  x86/UV2: Work around BAU bug
  x86/UV2: Fix BAU destination timeout initialization
  x86/UV2: Fix new UV2 hardware by using native UV2 broadcast mode
  x86: Get rid of dubious one-bit signed bitfield

gpio bug fixes for v3.3

* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  gpio: tps65910: Use correct offset for gpio initialization
  gpio/it8761e: Restrict it8761e gpio driver to x86.
  gpio-ml-ioh: cleanup __iomem annotation usage
  gpio-ml-ioh: cleanup NULL pointer checking
  gpio-pch: cleanup __iomem annotation usage
  gpio-pch: cleanup NULL pointer checking

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  qnx4: don't leak ->BitMap on late failure exits
  qnx4: reduce the insane nesting in qnx4_checkroot()
  qnx4: di_fname is an array, for crying out loud...
  vfs: remove printk from set_nlink()
  wake up s_wait_unfrozen when ->freeze_fs fails

In checkin

  303395ac x86: Generate system call tables and unistd_*.h from tables

the feature macros in <asm/unistd.h> were unified between 32 and 64
bits.  Unfortunately 32 bits requires __ARCH_WANT_SYS_IPC and this was
inadvertently dropped.
Reported-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/CALLzPKbeXN5gdngo8uYYU8mAow=XhrwBFBhKfG811f37BubQOg@mail.gmail.com

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  KEYS: Permit key_serial() to be called with a const key pointer
  keys: fix user_defined key sparse messages
  ima: fix cred sparse warning
  MPILIB: Add a missing ENOMEM check

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

(struct qnx4_inode_entry *)(bh->b_data + some_offset)->di_fname
is not going to be NULL, TYVM...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Permit key_serial() to be called with a const key pointer.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>

Replace the rcu_assign_pointer() calls with rcu_assign_keypointer().
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>

Fix ima_policy.c sparse "warning: dereference of noderef expression"
message, by accessing cred->uid using current_cred().

Changelog v1:
- Change __cred to just cred (based on David Howell's comment)
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>