If the device state GPIO is not connected to the host then disable the
INH output from the TCAN device per section 8.3.5 of the data sheet.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

It's a good idea to reset a ip-block/spi device before using it, this
patch will reset the device.

And a generic reset function if needed elsewhere.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The tcan4x5x_parse_config() function now performs action on the device
either reading or writing and a reset. If the devive has a switchable
power supppy (i.e. regulator is managed) it needs to be turned on.

So turn on the regulator if available. If the parsing fails, turn off
the regulator.

Fixes: 2de49735 ("can: tcan45x: Make wake-up GPIO an optional GPIO")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The m_can tries to detect if Non ISO Operation is available while in
standby mode, this function results in the following error:

| tcan4x5x spi2.0 (unnamed net_device) (uninitialized): Failed to init module
| tcan4x5x spi2.0: m_can device registered (irq=84, version=32)
| tcan4x5x spi2.0 can2: TCAN4X5X successfully initialized.

When the tcan device comes out of reset it goes in standby mode. The
m_can driver tries to access the control register but fails due to the
device being in standby mode.

So this patch will put the tcan device in normal mode before the m_can
driver does the initialization.

Fixes: 5443c226 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Pull networking fixes from David Miller:

 1) Fix big endian overflow in nf_flow_table, from Arnd Bergmann.

 2) Fix port selection on big endian in nft_tproxy, from Phil Sutter.

 3) Fix precision tracking for unbound scalars in bpf verifier, from
    Daniel Borkmann.

 4) Fix integer overflow in socket rcvbuf check in UDP, from Antonio
    Messina.

 5) Do not perform a neigh confirmation during a pmtu update over a
    tunnel, from Hangbin Liu.

 6) Fix DMA mapping leak in dpaa_eth driver, from Madalin Bucur.

 7) Various PTP fixes for sja1105 dsa driver, from Vladimir Oltean.

 8) Add missing to dummy definition of of_mdiobus_child_is_phy(), from
    Geert Uytterhoeven

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
  hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename()
  net/sched: add delete_empty() to filters and use it in cls_flower
  tcp: Fix highest_sack and highest_sack_seq
  ptp: fix the race between the release of ptp_clock and cdev
  net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S
  Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation
  net: dsa: sja1105: Remove restriction of zero base-time for taprio offload
  net: dsa: sja1105: Really make the PTP command read-write
  net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot
  cxgb4/cxgb4vf: fix flow control display for auto negotiation
  mlxsw: spectrum: Use dedicated policer for VRRP packets
  mlxsw: spectrum_router: Skip loopback RIFs during MAC validation
  net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs
  net/sched: act_mirred: Pull mac prior redir to non mac_header_xmit device
  net_sched: sch_fq: properly set sk->sk_pacing_status
  bnx2x: Fix accounting of vlan resources among the PFs
  bnx2x: Use appropriate define for vlan credit
  of: mdio: Add missing inline to of_mdiobus_child_is_phy() dummy
  net: phy: aquantia: add suspend / resume ops for AQR105
  dpaa_eth: fix DMA mapping leak
  ...

Pull tomoyo fixes from Tetsuo Handa:
 "Two bug fixes:

   - Suppress RCU warning at list_for_each_entry_rcu()

   - Don't use fancy names on sockets"

* tag 'tomoyo-fixes-for-5.5' of git://git.osdn.net/gitroot/tomoyo/tomoyo-test1:
  tomoyo: Suppress RCU warning at list_for_each_entry_rcu().
  tomoyo: Don't use nifty names on sockets.

hsr slave interfaces don't have debugfs directory.
So, hsr_debugfs_rename() shouldn't be called when hsr slave interface name
is changed.

Test commands:
    ip link add dummy0 type dummy
    ip link add dummy1 type dummy
    ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
    ip link set dummy0 name ap

Splat looks like:
[21071.899367][T22666] ap: renamed from dummy0
[21071.914005][T22666] ==================================================================
[21071.919008][T22666] BUG: KASAN: slab-out-of-bounds in hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.923640][T22666] Read of size 8 at addr ffff88805febcd98 by task ip/22666
[21071.926941][T22666]
[21071.927750][T22666] CPU: 0 PID: 22666 Comm: ip Not tainted 5.5.0-rc2+ #240
[21071.929919][T22666] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[21071.935094][T22666] Call Trace:
[21071.935867][T22666]  dump_stack+0x96/0xdb
[21071.936687][T22666]  ? hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.937774][T22666]  print_address_description.constprop.5+0x1be/0x360
[21071.939019][T22666]  ? hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.940081][T22666]  ? hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.940949][T22666]  __kasan_report+0x12a/0x16f
[21071.941758][T22666]  ? hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.942674][T22666]  kasan_report+0xe/0x20
[21071.943325][T22666]  hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.944187][T22666]  hsr_netdev_notify+0x1fe/0x9b0 [hsr]
[21071.945052][T22666]  ? __module_text_address+0x13/0x140
[21071.945897][T22666]  notifier_call_chain+0x90/0x160
[21071.946743][T22666]  dev_change_name+0x419/0x840
[21071.947496][T22666]  ? __read_once_size_nocheck.constprop.6+0x10/0x10
[21071.948600][T22666]  ? netdev_adjacent_rename_links+0x280/0x280
[21071.949577][T22666]  ? __read_once_size_nocheck.constprop.6+0x10/0x10
[21071.950672][T22666]  ? lock_downgrade+0x6e0/0x6e0
[21071.951345][T22666]  ? do_setlink+0x811/0x2ef0
[21071.951991][T22666]  do_setlink+0x811/0x2ef0
[21071.952613][T22666]  ? is_bpf_text_address+0x81/0xe0
[ ... ]

Reported-by: syzbot+9328206518f08318a5fd@syzkaller.appspotmail.com
Fixes: 4c2d5e33 ("hsr: rename debugfs file when interface name is changed")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "net/sched: cls_u32: fix refcount leak in the error path of
u32_change()", and fix the u32 refcount leak in a more generic way that
preserves the semantic of rule dumping.
On tc filters that don't support lockless insertion/removal, there is no
need to guard against concurrent insertion when a removal is in progress.
Therefore, for most of them we can avoid a full walk() when deleting, and
just decrease the refcount, like it was done on older Linux kernels.
This fixes situations where walk() was wrongly detecting a non-empty
filter, like it happened with cls_u32 in the error path of change(), thus
leading to failures in the following tdc selftests:

 6aa7: (filter, u32) Add/Replace u32 with source match and invalid indev
 6658: (filter, u32) Add/Replace u32 with custom hash table and invalid handle
 74c2: (filter, u32) Add/Replace u32 filter with invalid hash table id

On cls_flower, and on (future) lockless filters, this check is necessary:
move all the check_empty() logic in a callback so that each filter
can have its own implementation. For cls_flower, it's sufficient to check
if no IDRs have been allocated.

This reverts commit 275c44aa.

Changes since v1:
 - document the need for delete_empty() when TCF_PROTO_OPS_DOIT_UNLOCKED
   is used, thanks to Vlad Buslov
 - implement delete_empty() without doing fl_walk(), thanks to Vlad Buslov
 - squash revert and new fix in a single patch, to be nice with bisect
   tests that run tdc on u32 filter, thanks to Dave Miller

Fixes: 275c44aa ("net/sched: cls_u32: fix refcount leak in the error path of u32_change()")
Fixes: 6676d5e4 ("net: sched: set dedicated tcf_walker flag when tp is empty")
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Suggested-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

>From commit 50895b9d ("tcp: highest_sack fix"), the logic about
setting tp->highest_sack to the head of the send queue was removed.
Of course the logic is error prone, but it is logical. Before we
remove the pointer to the highest sack skb and use the seq instead,
we need to set tp->highest_sack to NULL when there is no skb after
the last sack, and then replace NULL with the real skb when new skb
inserted into the rtx queue, because the NULL means the highest sack
seq is tp->snd_nxt. If tp->highest_sack is NULL and new data sent,
the next ACK with sack option will increase tp->reordering unexpectedly.

This patch sets tp->highest_sack to the tail of the rtx queue if
it's NULL and new data is sent. The patch keeps the rule that the
highest_sack can only be maintained by sack processing, except for
this only case.

Fixes: 50895b9d ("tcp: highest_sack fix")
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a case when a ptp chardev (like /dev/ptp0) is open but an underlying
device is removed, closing this file leads to a race. This reproduces
easily in a kvm virtual machine:

ts# cat openptp0.c
int main() { ... fp = fopen("/dev/ptp0", "r"); ... sleep(10); }
ts# uname -r
5.5.0-rc3-46cf053e
ts# cat /proc/cmdline
... slub_debug=FZP
ts# modprobe ptp_kvm
ts# ./openptp0 &
[1] 670
opened /dev/ptp0, sleeping 10s...
ts# rmmod ptp_kvm
ts# ls /dev/ptp*
ls: cannot access '/dev/ptp*': No such file or directory
ts# ...woken up
[   48.010809] general protection fault: 0000 [#1] SMP
[   48.012502] CPU: 6 PID: 658 Comm: openptp0 Not tainted 5.5.0-rc3-46cf053e #25
[   48.014624] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
[   48.016270] RIP: 0010:module_put.part.0+0x7/0x80
[   48.017939] RSP: 0018:ffffb3850073be00 EFLAGS: 00010202
[   48.018339] RAX: 000000006b6b6b6b RBX: 6b6b6b6b6b6b6b6b RCX: ffff89a476c00ad0
[   48.018936] RDX: fffff65a08d3ea08 RSI: 0000000000000247 RDI: 6b6b6b6b6b6b6b6b
[   48.019470] ...                                              ^^^ a slub poison
[   48.023854] Call Trace:
[   48.024050]  __fput+0x21f/0x240
[   48.024288]  task_work_run+0x79/0x90
[   48.024555]  do_exit+0x2af/0xab0
[   48.024799]  ? vfs_write+0x16a/0x190
[   48.025082]  do_group_exit+0x35/0x90
[   48.025387]  __x64_sys_exit_group+0xf/0x10
[   48.025737]  do_syscall_64+0x3d/0x130
[   48.026056]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[   48.026479] RIP: 0033:0x7f53b12082f6
[   48.026792] ...
[   48.030945] Modules linked in: ptp i6300esb watchdog [last unloaded: ptp_kvm]
[   48.045001] Fixing recursive fault but reboot is needed!

This happens in:

static void __fput(struct file *file)
{   ...
    if (file->f_op->release)
        file->f_op->release(inode, file); <<< cdev is kfree'd here
    if (unlikely(S_ISCHR(inode->i_mode) && inode->i_cdev != NULL &&
             !(mode & FMODE_PATH))) {
        cdev_put(inode->i_cdev); <<< cdev fields are accessed here

Namely:

__fput()
  posix_clock_release()
    kref_put(&clk->kref, delete_clock) <<< the last reference
      delete_clock()
        delete_ptp_clock()
          kfree(ptp) <<< cdev is embedded in ptp
  cdev_put
    module_put(p->owner) <<< *p is kfree'd, bang!

Here cdev is embedded in posix_clock which is embedded in ptp_clock.
The race happens because ptp_clock's lifetime is controlled by two
refcounts: kref and cdev.kobj in posix_clock. This is wrong.

Make ptp_clock's sysfs device a parent of cdev with cdev_device_add()
created especially for such cases. This way the parent device with its
ptp_clock is not released until all references to the cdev are released.
This adds a requirement that an initialized but not exposed struct
device should be provided to posix_clock_register() by a caller instead
of a simple dev_t.

This approach was adopted from the commit 72139dfa ("watchdog: Fix
the race between the release of watchdog_core_data and cdev"). See
details of the implementation in the commit 233ed09d ("chardev: add
helper function to register char devs with a struct device").

Link: https://lore.kernel.org/linux-fsdevel/20191125125342.6189-1-vdronov@redhat.com/T/#uAnalyzed-by: Stephen Johnston <sjohnsto@redhat.com>
Analyzed-by: Vern Lovejoy <vlovejoy@redhat.com>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)

While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)

In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.

So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.

We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).

Fixes: f9a1a764 ("net: dsa: sja1105: Reverse TPID and TPID2")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 86db36a3 ("net: dsa: sja1105: Implement state machine
for TAS with PTP clock source"), this paragraph is no longer true. So
remove it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The check originates from the initial implementation which was not based
on PTP time but on a standalone clock source. In the meantime we can now
program the PTPSCHTM register at runtime with the dynamic base time
(actually with a value that is 200 ns smaller, to avoid writing DELTA=0
in the Schedule Entry Points Parameters Table). And we also have logic
for moving the actual base time in the future of the PHC's current time
base, so the check for zero serves no purpose, since even if the user
will specify zero, that's not what will end up in the static config
table where the limitation is.

Fixes: 86db36a3 ("net: dsa: sja1105: Implement state machine for TAS with PTP clock source")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When activating tc-taprio offload on the switch ports, the TAS state
machine will try to check whether it is running or not, but will find
both the STARTED and STOPPED bits as false in the
sja1105_tas_check_running function. So the function will return -EINVAL
(an abnormal situation) and the kernel will keep printing this from the
TAS FSM workqueue:

[   37.691971] sja1105 spi0.1: An operation returned -22

The reason is that the underlying function that gets called,
sja1105_ptp_commit, does not actually do a SPI_READ, but a SPI_WRITE. So
the command buffer remains initialized with zeroes instead of retrieving
the hardware state. Fix that.

Fixes: 41603d78 ("net: dsa: sja1105: Make the PTP command read-write")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PTP egress timestamp N must be captured from register PTPEGR_TS[n],
where n = 2 * PORT + TSREG. There are 10 PTPEGR_TS registers, 2 per
port. We are only using TSREG=0.

As opposed to the management slots, which are 4 in number
(SJA1105_NUM_PORTS, minus the CPU port). Any management frame (which
includes PTP frames) can be sent to any non-CPU port through any
management slot. When the CPU port is not the last port (#4), there will
be a mismatch between the slot and the port number.

Luckily, the only mainline occurrence with this switch
(arch/arm/boot/dts/ls1021a-tsn.dts) does have the CPU port as #4, so the
issue did not manifest itself thus far.

Fixes: 47ed985e ("net: dsa: sja1105: Add logic for TX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when
_only_ Rx pause is enabled, both symmetric and asymmetric pause
towards local device must be enabled. Also, firmware returns the local
device's flow control pause params as part of advertised capabilities
and negotiated params as part of current link attributes. So, fix up
ethtool's flow control pause params fetch logic to read from acaps,
instead of linkattr.

[1] https://standards.ieee.org/standard/802_3-2005.html

Fixes: c3168cab ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Signed-off-by: Surendra Mobiya <surendra@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Couple of fixes

This patch set contains two fixes for mlxsw. Please consider both for
stable.

Patch #1 from Amit fixes a wrong check during MAC validation when
creating router interfaces (RIFs). Given a particular order of
configuration this can result in the driver refusing to create new RIFs.

Patch #2 fixes a wrong trap configuration in which VRRP packets and
routing exceptions were policed by the same policer towards the CPU. In
certain situations this can prevent VRRP packets from reaching the CPU.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, VRRP packets and packets that hit exceptions during routing
(e.g., MTU error) are policed using the same policer towards the CPU.
This means, for example, that misconfiguration of the MTU on a routed
interface can prevent VRRP packets from reaching the CPU, which in turn
can cause the VRRP daemon to assume it is the Master router.

Fix this by using a dedicated policer for VRRP packets.

Fixes: 11566d34 ("mlxsw: spectrum: Add VRRP traps")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a router interface (RIF) is created the MAC address of the backing
netdev is verified to have the same MSBs as existing RIFs. This is
required in order to avoid changing existing RIF MAC addresses that all
share the same MSBs.

Loopback RIFs are special in this regard as they do not have a MAC
address, given they are only used to loop packets from the overlay to
the underlay.

Without this change, an error is returned when trying to create a RIF
after the creation of a GRE tunnel that is represented by a loopback
RIF. 'rif->dev->dev_addr' points to the GRE device's local IP, which
does not share the same MSBs as physical interfaces. Adding an IP
address to any physical interface results in:

Error: mlxsw_spectrum: All router interface MAC addresses must have the
same prefix.

Fix this by skipping loopback RIFs during MAC validation.

Fixes: 74bc9939 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull RISC-V fixes from Paul Walmsley:
 "One important fix for RISC-V:

   - Redirect any incoming syscall with an ID less than -1 to
     sys_ni_syscall, rather than allowing them to fall through into the
     syscall handler.

  and two minor build fixes:

   - Export __asm_copy_{from,to}_user() from where they are defined.
     This fixes a build error triggered by some randconfigs.

   - Export flush_icache_all(). I'd resisted this before, since
     historically we didn't want modules to be able to flush the I$
     directly; but apparently everyone else is doing it now"

* tag 'riscv/for-v5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: export flush_icache_all to modules
  riscv: reject invalid syscalls below -1
  riscv: fix compile failure with EXPORT_SYMBOL() & !MMU

Pull /proc/locks formatting fix from Jeff Layton:
 "This is a trivial fix for a _very_ long standing bug in /proc/locks
  formatting. Ordinarily, I'd wait for the merge window for something
  like this, but it is making it difficult to validate some overlayfs
  fixes.

  I've also gone ahead and marked this for stable"

* tag 'locks-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
  locks: print unsigned ino in /proc/locks

Pull cifs fixes from Steve French:
 "One performance fix for large directory searches, and one minor style
  cleanup noticed by Clang"

* tag '5.5-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Optimize readdir on reparse points
  cifs: Adjust indentation in smb2_open_file

An ino is unsigned, so display it as such in /proc/locks.

Cc: stable@vger.kernel.org
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>

This is needed by LKDTM (crash dump test module), it calls
flush_icache_range(), which on RISC-V turns into flush_icache_all(). On
other architectures, the actual implementation is exported, so follow
that precedence and export it here too.

Fixes build of CONFIG_LKDTM that fails with:
ERROR: "flush_icache_all" [drivers/misc/lkdtm/lkdtm.ko] undefined!
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>

Running "stress-ng --enosys 4 -t 20 -v" showed a large number of kernel oops
with "Unable to handle kernel paging request at virtual address" message. This
happens when enosys stressor starts testing random non-valid syscalls.

I forgot to redirect any syscall below -1 to sys_ni_syscall.

With the patch kernel oops messages are gone while running stress-ng enosys
stressor.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Fixes: 5340627e ("riscv: add support for SECCOMP and SECCOMP_FILTER")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>

When support for !MMU was added, the declaration of
__asm_copy_to_user() & __asm_copy_from_user() were #ifdefed
out hence their EXPORT_SYMBOL() give an error message like:
  .../riscv_ksyms.c:13:15: error: '__asm_copy_to_user' undeclared here
  .../riscv_ksyms.c:14:15: error: '__asm_copy_from_user' undeclared here

Since these symbols are not defined with !MMU it's wrong to export them.
Same for __clear_user() (even though this one is also declared in
include/asm-generic/uaccess.h and thus doesn't give an error message).

Fix this by doing the EXPORT_SYMBOL() directly where these symbols
are defined: inside lib/uaccess.S itself.

Fixes: 6bd33e1e ("riscv: fix compile failure with EXPORT_SYMBOL() & !MMU")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>

Pull SCSI fixes from James Bottomley:
 "Four fixes and one spelling update, all in drivers: two in lpfc and
  the rest in mp3sas, cxgbi and target"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: target/iblock: Fix protection error with blocks greater than 512B
  scsi: libcxgbi: fix NULL pointer dereference in cxgbi_device_destroy()
  scsi: lpfc: fix spelling mistakes of asynchronous
  scsi: lpfc: fix build failure with DEBUGFS disabled
  scsi: mpt3sas: Fix double free in attach error handling

GXBB and newer SoCs use the fixed FCLK_DIV2 (1GHz) clock as input for
the m250_sel clock. Meson8b and Meson8m2 use MPLL2 instead, whose rate
can be adjusted at runtime.

So far we have been running MPLL2 with ~250MHz (and the internal
m250_div with value 1), which worked enough that we could transfer data
with an TX delay of 4ns. Unfortunately there is high packet loss with
an RGMII PHY when transferring data (receiving data works fine though).
Odroid-C1's u-boot is running with a TX delay of only 2ns as well as
the internal m250_div set to 2 - no lost (TX) packets can be observed
with that setting in u-boot.

Manual testing has shown that the TX packet loss goes away when using
the following settings in Linux (the vendor kernel uses the same
settings):
- MPLL2 clock set to ~500MHz
- m250_div set to 2
- TX delay set to 2ns on the MAC side

Update the m250_div divider settings to only accept dividers greater or
equal 2 to fix the TX delay generated by the MAC.

iperf3 results before the change:
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec   182 MBytes   153 Mbits/sec  514      sender
[  5]   0.00-10.00  sec   182 MBytes   152 Mbits/sec           receiver

iperf3 results after the change (including an updated TX delay of 2ns):
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-10.00  sec   927 MBytes   778 Mbits/sec    0      sender
[  5]   0.00-10.01  sec   927 MBytes   777 Mbits/sec           receiver

Fixes: 4f6a71b8 ("net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's no skb_pull performed when a mirred action is set at egress of a
mac device, with a target device/action that expects skb->data to point
at the network header.

As a result, either the target device is errornously given an skb with
data pointing to the mac (egress case), or the net stack receives the
skb with data pointing to the mac (ingress case).

E.g:
 # tc qdisc add dev eth9 root handle 1: prio
 # tc filter add dev eth9 parent 1: prio 9 protocol ip handle 9 basic \
   action mirred egress redirect dev tun0

 (tun0 is a tun device. result: tun0 errornously gets the eth header
  instead of the iph)

Revise the push/pull logic of tcf_mirred_act() to not rely on the
skb_at_tc_ingress() vs tcf_mirred_act_wants_ingress() comparison, as it
does not cover all "pull" cases.

Instead, calculate whether the required action on the target device
requires the data to point at the network header, and compare this to
whether skb->data points to network header - and make the push/pull
adjustments as necessary.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Shmulik Ladkani <sladkani@proofpoint.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull drm fixes from Dave Airlie:
 "Post-xmas food coma recovery fixes. Only three fixes for i915 since I
  expect most people are holidaying.

  i915:
   - power management rc6 fix
   - framebuffer tracking fix
   - display power management ratelimit fix"

* tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm:
  drm/i915: Hold reference to intel_frontbuffer as we track activity
  drm/i915/gt: Ratelimit display power w/a
  drm/i915/pmu: Ensure monotonic rc6

Merge tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fixes from Shuah Khan:

 - rseq build failures fixes related to glibc 2.30 compatibility from
   Mathieu Desnoyers

 - Kunit fixes and cleanups from SeongJae Park

 - Fixes to filesystems/epoll, firmware, and livepatch build failures
   and skip handling.

* tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  rseq/selftests: Clarify rseq_prepare_unload() helper requirements
  rseq/selftests: Fix: Namespace gettid() for compatibility with glibc 2.30
  rseq/selftests: Turn off timeout setting
  kunit/kunit_tool_test: Test '--build_dir' option run
  kunit: Rename 'kunitconfig' to '.kunitconfig'
  kunit: Place 'test.log' under the 'build_dir'
  kunit: Create default config in '--build_dir'
  kunit: Remove duplicated defconfig creation
  docs/kunit/start: Use in-tree 'kunit_defconfig'
  selftests: livepatch: Fix it to do root uid check and skip
  selftests: firmware: Fix it to do root uid check and skip
  selftests: filesystems/epoll: fix build error

Pull power management fixes from Rafael Wysocki:
 "Fix compile test of the Tegra devfreq driver (Arnd Bergmann) and
  remove redundant Kconfig dependencies from multiple devfreq drivers
  (Leonard Crestez)"

* tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / devfreq: tegra: Add COMMON_CLK dependency
  PM / devfreq: Drop explicit selection of PM_OPP

Pull io_uring fixes from Jens Axboe:

 - Removal of now unused busy wqe list (Hillf)

 - Add cond_resched() to io-wq work processing (Hillf)

 - And then the series that I hinted at from last week, which removes
   the sqe from the io_kiocb and keeps all sqe handling on the prep
   side. This guarantees that an opcode can't do the wrong thing and
   read the sqe more than once. This is unchanged from last week, no
   issues have been observed with this in testing. Hence I really think
   we should fold this into 5.5.

* tag 'io_uring-5.5-20191226' of git://git.kernel.dk/linux-block:
  io-wq: add cond_resched() to worker thread
  io-wq: remove unused busy list from io_sqe
  io_uring: pass in 'sqe' to the prep handlers
  io_uring: standardize the prep methods
  io_uring: read 'count' for IORING_OP_TIMEOUT in prep handler
  io_uring: move all prep state for IORING_OP_{SEND,RECV}_MGS to prep handler
  io_uring: move all prep state for IORING_OP_CONNECT to prep handler
  io_uring: add and use struct io_rw for read/writes
  io_uring: use u64_to_user_ptr() consistently

Pull libata fixes from Jens Axboe:
 "Two things in here:

   - First half of a series that fixes ahci_brcm, also marked for
     stable. The other part of the series is going into 5.6 (Florian)

   - sata_nv regression fix that is also marked for stable (Sascha)"

* tag 'libata-5.5-20191226' of git://git.kernel.dk/linux-block:
  ata: ahci_brcm: Add missing clock management during recovery
  ata: ahci_brcm: BCM7425 AHCI requires AHCI_HFLAG_DELAY_ENGINE
  ata: ahci_brcm: Fix AHCI resources management
  ata: libahci_platform: Export again ahci_platform_<en/dis>able_phys()
  libata: Fix retrieving of active qcs

Pull block fixes from Jens Axboe:
 "Only thing here are the changes from Arnd from last week, which now
  have the appropriate header include to ensure they actually compile if
  COMPAT is enabled"

* tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block:
  compat_ioctl: block: handle Persistent Reservations
  compat_ioctl: block: handle add zone open, close and finish ioctl
  compat_ioctl: block: handle BLKGETZONESZ/BLKGETNRZONES
  compat_ioctl: block: handle BLKREPORTZONE/BLKRESETZONE
  pktcdvd: fix regression on 64-bit architectures

Pull GPIO fixes from Linus Walleij:
 "A set of fixes for the v5.5 series:

   - Fix the build for the Xtensa driver.

   - Make sure to set up the parent device for mpc8xxx.

   - Clarify the look-up error message.

   - Fix the usage of the line direction in the mockup device.

   - Fix a type warning on the Aspeed driver.

   - Remove the pointless __exit annotation on the xgs-iproc which is
     causing a compilation problem.

   - Fix up emultation of open drain outputs .get_direction()

   - Fix the IRQ callbacks on the PCA953xx to use bitops and work
     properly.

   - Fix the Kconfig on the Tegra driver"

* tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: tegra186: Allow building on Tegra194-only configurations
  gpio: pca953x: Switch to bitops in IRQ callbacks
  gpiolib: fix up emulated open drain outputs
  MAINTAINERS: Append missed file to the database
  gpio: xgs-iproc: remove __exit annotation for iproc_gpio_remove
  gpio: aspeed: avoid return type warning
  gpio: mockup: Fix usage of new GPIO_LINE_DIRECTION
  gpio: Fix error message on out-of-range GPIO in lookup table
  gpio: mpc8xxx: Add platform device to gpiochip->parent
  gpio: xtensa: fix driver build

Merge tag 'drm-intel-fixes-2019-12-23' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

i915 power and frontbuffer tracking fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87r20vdlrs.fsf@intel.com

If fq_classify() recycles a struct fq_flow because
a socket structure has been reallocated, we do not
set sk->sk_pacing_status immediately, but later if the
flow becomes detached.

This means that any flow requiring pacing (BBR, or SO_MAX_PACING_RATE)
might fallback to TCP internal pacing, which requires a per-socket
high resolution timer, and therefore more cpu cycles.

Fixes: 218af599 ("tcp: internal implementation for pacing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Manish Chopra says:

====================
bnx2x: Bug fixes

This series has changes in the area of vlan resources
management APIs to fix fw assert issue reported in max
vlan configuration testing over the PF.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>