With 4 pages (16Kb), we can't fit 10 frames in the aggregation buffer
during iperf.  This is the optimal for the firmware.  Thus, increase
the buffer size by one page.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Instead of adding more files from the lower drivers into the same
directory in debugfs as wlcore, we now add a subdirectory for the
lower driver.  This makes things a bit easier, because we can quickly
see where the debugfs entry is implemented and what is specific to the
lower driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Yet another temporary module parameter requested by the firmware team.
This will be replaced by the conf binary.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

We use hardcoded values for the different board types.  In some cases
we may need to override the defaults, so export the values as module
params.  If not defined, the defaults for the specified board type
will be used.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

With more recent PHY firmware versions (>8.1.0.0.116), we need to use
the correct value for the pwr_limit_reference_11_abg parameter when
setting the mac_and_phy options.

For now we use a hardcoded 0xc8 as the value.  This will be moved to
the configuration binary when it gets implemented.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

In some cases it may be useful to force narrow-band SISO channels.
Add a new value to the ht_mode module parameter to force the device to
operate in SISO 20MHz.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

We were setting all the rates bits when starting the AP role.  Instead
of doing this, we should set only the rates we really support
(eg. MIMO rates or wide-channel rates).  This commit changes that so
that we always use the default rates (basic rates + MCS0-7) and add
the values returned by the ap_get_mimo_wide_rate_mask operation.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

If the wl18xx module is loaded with ht_mode=wide (the default), we
shouldn't use MIMO rates when the channel type is not HT40.  Fix this
by checking the ht_mode before deciding which rates to used.
Additionally, set the ht_mode parameter explicitly to "wide" as the
default.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

In some cases it may be useful for debugging to check what is the
status of the interrupt register when a hardware recovery happens.
Print the contents of REG_INTERRUPT_NO_CLEAR (aka. HINT_STS_RAW) when
recovery starts.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

The wl18xx firmware writes the PHY firmware version in the static
data.  Add an operation to parse the static data and print the PHY
firmware version when booting.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

The wl18xx firmware has more information in the static_data than
wl12xx.  To be able to parse that in an abstracted way, this patch
adds a priv area to the static data struct and an operation that
allows the lower driver to parse it if necessary.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Implement the operations that are necessary to fetch the
wl18xx-specific FW statistics and export them in debugfs.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Implement the operations that are necessary to fetch the
wl12xx-specific FW statistics.  Re-add some of the code removed from
wlcore.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Add a macro to make it easy to print arrays from the FW statistics
array in debugfs.  At the same time, increase the buffer size so
arrays fit more easily.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

The FW statistics differ from hardware to hardware.  This commit
prepares for hardware-specific implementation of the FW statistics
debugfs entries.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Sometimes we get a BSS_CHANGED_BEACON_ENABLED event before the basic
rates have been properly set.  To avoid problems with the firmware not
expecting to receive frames at rates that are not set during
CMD_START_ROLE, we now start with all basic rates by default.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

When the data rates change, we get BSS_CHANGED_BASIC_RATES.  At this
point, we should update all the templates to match the new rates.  We
were changing some of the templates, but the beacon and the probe
response templates were missing.

[Remove redundant min_rate variable - Arik]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

There are some problems with MCS_13 in PG 1.0 hardware.  So we disable
it when PG 1.0 is detected.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

We can do get the HW information and identify the chip already at
probe time.  This makes it easier to mangle with the parameters during
identify chip before registering the hardware with mac80211.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Like HDK, COM8 uses 0x06 for the low_band_component_type as well.
Hardcode the value for COM8 until this configuration can be done in
the external configuration binary (to be implemented).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

When allocating the fw_status structure, the space for the
lower-driver private area was missing.  This was causing an illegal
write outside the allocated area, which was causing random oopses
around the kernel.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Since the most common board we're using now is an HDK board, change
the default board_type to hdk.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

We were changing the low_band_component_type in the private
configuration structure before copying the default values to it, so
the change was overwritten and only took effect after HW recovery.
Reported-by: Dror Erez <drorer@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

In some cases we may want to dump all the SDIO data in order to get
detailed information for debugging the communication with the
firmware.

Add printks to dump the data and a module parameter to enable/disable
it.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

In wl18xx we don't have an NVS yet, so we need to control whether 11a
is supported with a module parameter for now.  11a support is enabled
by default and can be changed by setting enable_11a to false when
loading the module.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Add the get_mac operation in order to fetch the BD_ADDR from fuse ROM,
so that we can derive the WLAN MAC addresses from it.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

The number of RX packet descriptors may vary from chip to chip and
in different firmware versions.  Unfortunately, the array that
contains the actual descriptors is in the middle of the fw_status
structure.  To manage this, we split the struct into two so we can
calculate the offset of what comes after the array and access the last
elements more easily.

[Changed the STATUS_LEN macro to be placement agnostic - Arik]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Add a new module parameter to disable TCP checksum offload.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

We need to specify the number of 2.4GHz and 5GHz antennas and whether
the board has an internal or external DC2DC.  Add some module
parameters that allow changing that.

In the future this will come from the "NVS" file.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Currently, all HDK boards use low_band_component_type 0x06.  In the
future this may change, but for now, we hardcode this value when the
board_type is set to HDK.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Add the correct FW name for PLT (which is the same as the normal
firmware) and implement the plt_init operation.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

PLT mode needs to be initialized differently for each chip.  This
patch adds an operation to init PLT and moves the existing PLT
initialization into the wl12xx driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Add more board types and remove a now unneeded write to SCR_PAD2 setting
the board type.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

In this chip family the NVS file should not be uploaded to FW. In fact,
we encounter strange bugs (sdio errors) when trying to upload it with
certain parameters.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

This ensures the index is 0 on FW recovery and prevents spurious error
prints - "WARNING illegal id in tx completion".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Only wl127x chips use the rx_mem_pool_addr values, which need to be
given to the firmware as part of the RX path.  Move this from core to
the wl12xx driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Read the HW PG version of the 18xx chip from FUSE.

Based on an earlier patch by Luciano Coelho <coelho@ti.com>.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Only wl12xx needs to get the ref_clock anc tcxo_clock values from the
platform data.  Move these elements from the wl1271 structure to
wl12xx's private data.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

The wl12xx.h file now contains mostly definitions that are internal to
wlcore.  Still, some things need to me moved to the public header, so
for now we keep including it in wlcore.h.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

Instead of using hardcoded values for a single frequency, we need to
read the frequency and use the appropriate values for it in the top
initialization.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>