Jeff Kirsher says:

====================
Intel Wired LAN Driver Fixes 2019-03-26

This series contains updates to igb, ixgbe, i40e and fm10k.

Jake fixes an issue with PTP in i40e where a previous commit resulted
in a regression where the driver would interpret small negative
adjustments as large positive additions, resulting in incorrect
behavior.

Arvind Sankar fixes an issue in igb where a previous commit would cause
a warning in the PCI pm core and resulted in pci_pm_runtime_suspend
would not call pci_save_state or pci_finish_runtime_suspend.

Ivan Vecera fixes MDIO bus registration with ixgbe, where the driver was
ignoring errors returned when registering and would leave the pointer in
a NULL state which triggered a BUG when un-registering.

Stefan Assmann fixes the check for Wake-On-LAN for i40e, which only
supports magic packet.

Yue Haibing fixes a potential NULL pointer de-reference in fm10k by
adding a simple check if the value is NULL.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
Here are some batman-adv bugfixes:

 - Fix refcount underflows in bridge loop avoidance code,
   by Sven Eckelmann (3 patches)

 - Fix warning when CFG80211 isn't enabled, by Anders Roxell

 - Fix genl notification for throughput override, by Sven Eckelmann

====================
Signed-off-by: David S. Miller <davem@davemloft.net>

VRF devices don't work with upper devices. Currently, it's possible to
add a VRF device to a bridge or team, and to create macvlan, macsec, or
ipvlan devices on top of a VRF (bond and vlan are prevented respectively
by the lack of an ndo_set_mac_address op and the NETIF_F_VLAN_CHALLENGED
feature flag).

Fix this by setting the IFF_NO_RX_HANDLER flag (introduced in commit
f5426250 ("net: introduce IFF_NO_RX_HANDLER")).

Cc: David Ahern <dsahern@gmail.com>
Fixes: 193125db ("net: Introduce VRF device driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dean Nelson says:

====================
thunderx: fix receive buffer page recycling

In attempting to optimize receive buffer page recycling for XDP, commit
77322538 ("net: thunderx: Optimize page recycling for XDP")
inadvertently introduced two problems for the non-XDP case, that will be
addressed by this patch series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

For the non-XDP case, commit 77322538 ("net: thunderx: Optimize
page recycling for XDP") added code to nicvf_free_rbdr() that, when releasing
the additional receive buffer page reference held for recycling, repeatedly
calls put_page() until the page's _refcount goes to zero. Which results in
the page being freed.

This is not okay if the page's _refcount was greater than 1 (in the non-XDP
case), because nicvf_free_rbdr() should not be subtracting more than what
nicvf_alloc_page() had previously added to the page's _refcount, which was
only 1 (in the non-XDP case).

This can arise if a received packet is still being processed and the receive
buffer (i.e., skb->head) has not yet been freed via skb_free_head() when
nicvf_free_rbdr() is spinning through the aforementioned put_page() loop.

If this should occur, when the received packet finishes processing and
skb_free_head() is called, various problems can ensue. Exactly what, depends on
whether the page has already been reallocated or not, anything from "BUG: Bad
page state ... ", to "Unable to handle kernel NULL pointer dereference ..." or
"Unable to handle kernel paging request...".

So this patch changes nicvf_free_rbdr() to only call put_page() once for pages
held for recycling (in the non-XDP case).

Fixes: 77322538 ("net: thunderx: Optimize page recycling for XDP")
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 77322538 ("net: thunderx: Optimize page recycling for XDP")
added code to nicvf_alloc_page() that inadvertently disables receive buffer
page recycling for the non-XDP case by always NULL'ng the page pointer.

This patch corrects two if-conditionals to allow for the recycling of non-XDP
mode pages by only setting the page pointer to NULL when the page is not ready
for recycling.

Fixes: 77322538 ("net: thunderx: Optimize page recycling for XDP")
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With a recent link mode advertisement code update this helper
providing local pause capability translation used for flow
control link mode negotiation got broken.
For eth drivers using this helper, the issue is apparent only
if either PAUSE or ASYM_PAUSE is being advertised.

Fixes: 3c1bcc86 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the rules for configuring search paths in Kbuild have
changed, this will lead some erros when compiling hns3 with the
following command:

make O=DIR M=drivers/net/ethernet/hisilicon/hns3

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.c:11:10:
fatal error: hnae3.h: No such file or directory

This patch fix it by adding $(srctree)/ prefix to the serach paths.
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ila_xlat_nl_cmd_flush uses rhashtable walkers allocated from the
stack but it never frees them.  This corrupts the walker list of
the hash table.

This patch fixes it.

Reported-by: syzbot+dae72a112334aa65a159@syzkaller.appspotmail.com
Fixes: b6e71bde ("ila: Flush netlink command to clear xlat...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS still pointed to phy.txt after moving this file into the rst
format, fix this.
Reported-by: Joe Perches <joe@perches.com>
Fixes: 25fe02d0 ("Documentation: net: phy: switch documentation to rst format")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Christoph reported a stall while peeking datagram with an offset when
busy polling is enabled. __skb_try_recv_datagram() uses as the loop
termination condition 'queue empty'. When peeking, the socket
queue can be not empty, even when no additional packets are received.

Address the issue explicitly checking for receive queue changes,
as currently done by __skb_wait_for_more_packets().

Fixes: 2b5cd0df ("net: Change return type of sk_busy_loop from bool to void")
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patches fixes few issues in mv88e6390x_port_set_cmode().

1. When entering the function the old cmode may be 0, in this case
   mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail
   out and have no chance to set a new mode. Therefore deal properly
   with -ENODEV.

2. Once we have disabled power and irq, let's set the cached cmode to 0.
   This reflects the actual status and is cleaner if we bail out with an
   error in the following function calls.

3. The cached cmode is used by mv88e6390x_serdes_get_lane(),
   mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable().
   Currently we set the cached mode to the new one at the very end of
   the function only, means until then we use the old one what may be
   wrong.

4. When calling mv88e6390_serdes_irq_enable() we use the lane value
   belonging to the old cmode. Get the lane belonging to the new cmode
   before calling this function.

It's hard to provide a good "Fixes" tag because quite a few smaller
changes have been done to the code in question recently.

Fixes: d235c48b ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:
 "Fixes here and there, a couple new device IDs, as usual:

   1) Fix BQL race in dpaa2-eth driver, from Ioana Ciornei.

   2) Fix 64-bit division in iwlwifi, from Arnd Bergmann.

   3) Fix documentation for some eBPF helpers, from Quentin Monnet.

   4) Some UAPI bpf header sync with tools, also from Quentin Monnet.

   5) Set descriptor ownership bit at the right time for jumbo frames in
      stmmac driver, from Aaro Koskinen.

   6) Set IFF_UP properly in tun driver, from Eric Dumazet.

   7) Fix load/store doubleword instruction generation in powerpc eBPF
      JIT, from Naveen N. Rao.

   8) nla_nest_start() return value checks all over, from Kangjie Lu.

   9) Fix asoc_id handling in SCTP after the SCTP_*_ASSOC changes this
      merge window. From Marcelo Ricardo Leitner and Xin Long.

  10) Fix memory corruption with large MTUs in stmmac, from Aaro
      Koskinen.

  11) Do not use ipv4 header for ipv6 flows in TCP and DCCP, from Eric
      Dumazet.

  12) Fix topology subscription cancellation in tipc, from Erik Hugne.

  13) Memory leak in genetlink error path, from Yue Haibing.

  14) Valid control actions properly in packet scheduler, from Davide
      Caratti.

  15) Even if we get EEXIST, we still need to rehash if a shrink was
      delayed. From Herbert Xu.

  16) Fix interrupt mask handling in interrupt handler of r8169, from
      Heiner Kallweit.

  17) Fix leak in ehea driver, from Wen Yang"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (168 commits)
  dpaa2-eth: fix race condition with bql frame accounting
  chelsio: use BUG() instead of BUG_ON(1)
  net: devlink: skip info_get op call if it is not defined in dumpit
  net: phy: bcm54xx: Encode link speed and activity into LEDs
  tipc: change to check tipc_own_id to return in tipc_net_stop
  net: usb: aqc111: Extend HWID table by QNAP device
  net: sched: Kconfig: update reference link for PIE
  net: dsa: qca8k: extend slave-bus implementations
  net: dsa: qca8k: remove leftover phy accessors
  dt-bindings: net: dsa: qca8k: support internal mdio-bus
  dt-bindings: net: dsa: qca8k: fix example
  net: phy: don't clear BMCR in genphy_soft_reset
  bpf, libbpf: clarify bump in libbpf version info
  bpf, libbpf: fix version info and add it to shared object
  rxrpc: avoid clang -Wuninitialized warning
  tipc: tipc clang warning
  net: sched: fix cleanup NULL pointer exception in act_mirr
  r8169: fix cable re-plugging issue
  net: ethernet: ti: fix possible object reference leak
  net: ibm: fix possible object reference leak
  ...

Syzkaller report this:

kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN PTI
CPU: 0 PID: 4378 Comm: syz-executor.0 Tainted: G         C        5.0.0+ #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
RIP: 0010:__lock_acquire+0x95b/0x3200 kernel/locking/lockdep.c:3573
Code: 00 0f 85 28 1e 00 00 48 81 c4 08 01 00 00 5b 5d 41 5c 41 5d 41 5e 41 5f c3 4c 89 ea 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f 85 cc 24 00 00 49 81 7d 00 e0 de 03 a6 41 bc 00 00
RSP: 0018:ffff8881e3c07a40 EFLAGS: 00010002
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000010 RSI: 0000000000000000 RDI: 0000000000000080
RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
R10: ffff8881e3c07d98 R11: ffff8881c7f21f80 R12: 0000000000000001
R13: 0000000000000080 R14: 0000000000000000 R15: 0000000000000001
FS:  00007fce2252e700(0000) GS:ffff8881f2400000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fffc7eb0228 CR3: 00000001e5bea002 CR4: 00000000007606f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
 lock_acquire+0xff/0x2c0 kernel/locking/lockdep.c:4211
 __mutex_lock_common kernel/locking/mutex.c:925 [inline]
 __mutex_lock+0xdf/0x1050 kernel/locking/mutex.c:1072
 drain_workqueue+0x24/0x3f0 kernel/workqueue.c:2934
 destroy_workqueue+0x23/0x630 kernel/workqueue.c:4319
 __do_sys_delete_module kernel/module.c:1018 [inline]
 __se_sys_delete_module kernel/module.c:961 [inline]
 __x64_sys_delete_module+0x30c/0x480 kernel/module.c:961
 do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fce2252dc58 EFLAGS: 00000246 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000020000140
RBP: 0000000000000002 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fce2252e6bc
R13: 00000000004bcca9 R14: 00000000006f6b48 R15: 00000000ffffffff

If alloc_workqueue fails, it should return -ENOMEM, otherwise may
trigger this NULL pointer dereference while unloading drivers.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 0a38c17a ("fm10k: Remove create_workqueue")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The current check for WoL on i40e is broken. Code comment says only
magic packet is supported, so only check for that.

Fixes: 540a152d (i40e/ixgbe/igb: fail on new WoL flag setting WAKE_MAGICSECURE)
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The ixgbe ignores errors returned from mdiobus_register() and leaves
adapter->mii_bus non-NULL and MDIO bus state as MDIOBUS_ALLOCATED.
This triggers a BUG from mdiobus_unregister() during ixgbe_remove() call.

Fixes: 8fa10ef0 ("ixgbe: register a mdiobus")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The runtime_suspend device callbacks are not supposed to save
configuration state or change the power state. Commit fb29f76cc566
("igb: Fix an issue that PME is not enabled during runtime suspend")
changed the driver to not save configuration state during runtime
suspend, however the driver callback still put the device into a
low-power state. This causes a warning in the pci pm core and results in
pci_pm_runtime_suspend not calling pci_save_state or pci_finish_runtime_suspend.

Fix this by not changing the power state either, leaving that to pci pm
core, and make the same change for suspend callback as well.

Also move a couple of defines into the appropriate header file instead
of inline in the .c file.

Fixes: fb29f76cc566 ("igb: Fix an issue that PME is not enabled during runtime suspend")
Signed-off-by: Arvind Sankar <niveditas98@gmail.com>
Reviewed-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 0ac30ce4 ("i40e: fix up 32 bit timespec references",
2017-07-26) claims to be cleaning up references to 32-bit timespecs.

The actual contents of the commit make no sense, as it converts a call
to timespec64_add into timespec64_add_ns. This would seem ok, if (a) the
change was documented in the commit message, and (b) timespec64_add_ns
supported negative numbers.

timespec64_add_ns doesn't work with signed deltas, because the
implementation is based around iter_div_u64_rem. This change resulted in
a regression where i40e_ptp_adjtime would interpret small negative
adjustments as large positive additions, resulting in incorrect
behavior.

This commit doesn't appear to fix anything, is not well explained, and
introduces a bug, so lets just revert it.

Reverts: 0ac30ce4 ("i40e: fix up 32 bit timespec references", 2017-07-26)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Stable fixes:
   - Fix nfs4_lock_state refcounting in nfs4_alloc_{lock,unlock}data()
   - fix mount/umount race in nlmclnt.
   - NFSv4.1 don't free interrupted slot on open

  Bugfixes:
   - Don't let RPC_SOFTCONN tasks time out if the transport is connected
   - Fix a typo in nfs_init_timeout_values()
   - Fix layoutstats handling during read failovers
   - fix uninitialized variable warning"

* tag 'nfs-for-5.1-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  SUNRPC: fix uninitialized variable warning
  pNFS/flexfiles: Fix layoutstats handling during read failovers
  NFS: Fix a typo in nfs_init_timeout_values()
  SUNRPC: Don't let RPC_SOFTCONN tasks time out if the transport is connected
  NFSv4.1 don't free interrupted slot on open
  NFS: fix mount/umount race in nlmclnt.
  NFS: Fix nfs4_lock_state refcounting in nfs4_alloc_{lock,unlock}data()

Avoid following compiler warning on uninitialized variable

net/sunrpc/xprtsock.c: In function ‘xs_read_stream_request.constprop’:
net/sunrpc/xprtsock.c:525:10: warning: ‘read’ may be used uninitialized in this function [-Wmaybe-uninitialized]
   return read;
          ^~~~
net/sunrpc/xprtsock.c:529:23: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  return ret < 0 ? ret : read;
         ~~~~~~~~~~~~~~^~~~~~
Signed-off-by: Alakesh Haloi <alakesh.haloi@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>

It might happen that Tx conf acknowledges a frame before it was
subscribed in bql, as subscribing was previously done after the enqueue
operation.

This patch moves the netdev_tx_sent_queue call before the actual frame
enqueue, so that this can never happen.

Fixes: 569dac6a ("dpaa2-eth: bql support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

clang warns about possible bugs in a dead code branch after
BUG_ON(1) when CONFIG_PROFILE_ALL_BRANCHES is enabled:

 drivers/net/ethernet/chelsio/cxgb4/sge.c:479:3: error: variable 'buf_size' is used uninitialized whenever 'if'
      condition is false [-Werror,-Wsometimes-uninitialized]
                BUG_ON(1);
                ^~~~~~~~~
 include/asm-generic/bug.h:61:36: note: expanded from macro 'BUG_ON'
 #define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
                                   ^~~~~~~~~~~~~~~~~~~
 include/linux/compiler.h:48:23: note: expanded from macro 'unlikely'
 #  define unlikely(x)   (__branch_check__(x, 0, __builtin_constant_p(x)))
                        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 drivers/net/ethernet/chelsio/cxgb4/sge.c:482:9: note: uninitialized use occurs here
        return buf_size;
               ^~~~~~~~
 drivers/net/ethernet/chelsio/cxgb4/sge.c:479:3: note: remove the 'if' if its condition is always true
                BUG_ON(1);
                ^
 include/asm-generic/bug.h:61:32: note: expanded from macro 'BUG_ON'
 #define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
                               ^
 drivers/net/ethernet/chelsio/cxgb4/sge.c:459:14: note: initialize the variable 'buf_size' to silence this warning
        int buf_size;
                    ^
                     = 0

Use BUG() here to create simpler code that clang understands
correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In dumpit, unlike doit, the check for info_get op being defined
is missing. Add it and avoid null pointer dereference in case driver
does not define this op.

Fixes: f9cf2288 ("devlink: add device information API")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously the green and amber LEDs on this quad PHY were solid, to
indicate an encoding of the link speed (10/100/1000).

This keeps the LEDs always on just as before, but now they flash on
Rx/Tx activity.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running a syz script, a panic occurred:

[  156.088228] BUG: KASAN: use-after-free in tipc_disc_timeout+0x9c9/0xb20 [tipc]
[  156.094315] Call Trace:
[  156.094844]  <IRQ>
[  156.095306]  dump_stack+0x7c/0xc0
[  156.097346]  print_address_description+0x65/0x22e
[  156.100445]  kasan_report.cold.3+0x37/0x7a
[  156.102402]  tipc_disc_timeout+0x9c9/0xb20 [tipc]
[  156.106517]  call_timer_fn+0x19a/0x610
[  156.112749]  run_timer_softirq+0xb51/0x1090

It was caused by the netns freed without deleting the discoverer timer,
while later on the netns would be accessed in the timer handler.

The timer should have been deleted by tipc_net_stop() when cleaning up a
netns. However, tipc has been able to enable a bearer and start d->timer
without the local node_addr set since Commit 52dfae5c ("tipc: obtain
node identity from interface by default"), which caused the timer not to
be deleted in tipc_net_stop() then.

So fix it in tipc_net_stop() by changing to check local node_id instead
of local node_addr, as Jon suggested.

While at it, remove the calling of tipc_nametbl_withdraw() there, since
tipc_nametbl_stop() will take of the nametbl's freeing after.

Fixes: 52dfae5c ("tipc: obtain node identity from interface by default")
Reported-by: syzbot+a25307ad099309f1c2b9@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

New device of QNAP based on aqc111u
Add this ID to blacklist of cdc_ether driver as well
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 8033 replaces the IETF draft for PIE
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements accessors for the QCA8337 MDIO access
through the MDIO_MASTER register, which makes it possible to
access the PHYs on slave-bus through the switch. In cases
where the switch ports are already mapped via external
"phy-phandles", the internal mdio-bus is disabled in order to
prevent a duplicated discovery and enumeration of the same
PHYs. Don't use mixed external and internal mdio-bus
configurations, as this is not supported by the hardware.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This belated patch implements Andrew Lunn's request of
"remove the phy_read() and phy_write() functions."
<https://lore.kernel.org/patchwork/comment/902734/>

While seemingly harmless, this causes the switch's user
port PHYs to get registered twice. This is because the
DSA subsystem will create a slave mdio-bus not knowing
that the qca8k_phy_(read|write) accessors operate on
the external mdio-bus. So the same "bus" gets effectively
duplicated.

Cc: stable@vger.kernel.org
Fixes: 6b93fb46 ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the qca8k's binding to document to the
approach for using the internal mdio-bus of the supported
qca8k switches.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the example, the phy at phy@0 is clashing with
the switch0@0 at the same address. Usually, the switches
are accessible through pseudo PHYs which in case of the
qca8k are located at 0x10 - 0x18.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull btrfs fixes from David Sterba:

 - fsync fixes: i_size for truncate vs fsync, dio vs buffered during
   snapshotting, remove complicated but incomplete assertion

 - removed excessive warnigs, misreported device stats updates

 - fix raid56 page mapping for 32bit arch

 - fixes reported by static analyzer

* tag 'for-5.1-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Btrfs: fix assertion failure on fsync with NO_HOLES enabled
  btrfs: Avoid possible qgroup_rsv_size overflow in btrfs_calculate_inode_block_rsv_size
  btrfs: Fix bound checking in qgroup_trace_new_subtree_blocks
  btrfs: raid56: properly unmap parity page in finish_parity_scrub()
  btrfs: don't report readahead errors and don't update statistics
  Btrfs: fix file corruption after snapshotting due to mix of buffered/DIO writes
  btrfs: remove WARN_ON in log_dir_items
  Btrfs: fix incorrect file size after shrinking truncate and fsync

Pull tracing fixes from Steven Rostedt:
 "Three small fixes:

   - A fix to a double free in the histogram code

   - Uninitialized variable fix

   - Use NULL instead of zero fix and spelling fixes"

* tag 'trace-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Fix warning using plain integer as NULL & spelling corrections
  tracing: initialize variable in create_dyn_event()
  tracing: Remove unnecessary var_ref destroy in track_data_destroy()

Pull file locking bugfix from Jeff Layton:
 "Just a single fix for a bug that crept into POSIX lock deadlock
  detection in v5.0"

* tag 'locks-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
  locks: wake any locks blocked on request before deadlock check

Changed  0 --> NULL to avoid sparse warning
Corrected spelling mistakes reported by checkpatch.pl
Sparse warning below:

sudo make C=2 CF=-D__CHECK_ENDIAN__ M=kernel/trace

CHECK   kernel/trace/ftrace.c
kernel/trace/ftrace.c:3007:24: warning: Using plain integer as NULL pointer
kernel/trace/ftrace.c:4758:37: warning: Using plain integer as NULL pointer

Link: http://lkml.kernel.org/r/20190323183523.GA2244@hari-Inspiron-1545Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

Fix compile warning in create_dyn_event(): 'ret' may be used uninitialized
in this function [-Wuninitialized].

Link: http://lkml.kernel.org/r/1553237900-8555-1-git-send-email-frowand.list@gmail.com

Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Fixes: 5448d44c ("tracing: Add unified dynamic event framework")
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

Commit 656fe2ba (tracing: Use hist trigger's var_ref array to
destroy var_refs) centralized the destruction of all the var_refs
in one place so that other code didn't have to do it.

The track_data_destroy() added later ignored that and also destroyed
the track_data var_ref, causing a double-free error flagged by KASAN.

==================================================================
BUG: KASAN: use-after-free in destroy_hist_field+0x30/0x70
Read of size 8 at addr ffff888086df2210 by task bash/1694

CPU: 6 PID: 1694 Comm: bash Not tainted 5.1.0-rc1-test+ #15
Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v03.03
07/14/2016
Call Trace:
 dump_stack+0x71/0xa0
 ? destroy_hist_field+0x30/0x70
 print_address_description.cold.3+0x9/0x1fb
 ? destroy_hist_field+0x30/0x70
 ? destroy_hist_field+0x30/0x70
 kasan_report.cold.4+0x1a/0x33
 ? __kasan_slab_free+0x100/0x150
 ? destroy_hist_field+0x30/0x70
 destroy_hist_field+0x30/0x70
 track_data_destroy+0x55/0xe0
 destroy_hist_data+0x1f0/0x350
 hist_unreg_all+0x203/0x220
 event_trigger_open+0xbb/0x130
 do_dentry_open+0x296/0x700
 ? stacktrace_count_trigger+0x30/0x30
 ? generic_permission+0x56/0x200
 ? __x64_sys_fchdir+0xd0/0xd0
 ? inode_permission+0x55/0x200
 ? security_inode_permission+0x18/0x60
 path_openat+0x633/0x22b0
 ? path_lookupat.isra.50+0x420/0x420
 ? __kasan_kmalloc.constprop.12+0xc1/0xd0
 ? kmem_cache_alloc+0xe5/0x260
 ? getname_flags+0x6c/0x2a0
 ? do_sys_open+0x149/0x2b0
 ? do_syscall_64+0x73/0x1b0
 ? entry_SYSCALL_64_after_hwframe+0x44/0xa9
 ? _raw_write_lock_bh+0xe0/0xe0
 ? __kernel_text_address+0xe/0x30
 ? unwind_get_return_address+0x2f/0x50
 ? __list_add_valid+0x2d/0x70
 ? deactivate_slab.isra.62+0x1f4/0x5a0
 ? getname_flags+0x6c/0x2a0
 ? set_track+0x76/0x120
 do_filp_open+0x11a/0x1a0
 ? may_open_dev+0x50/0x50
 ? _raw_spin_lock+0x7a/0xd0
 ? _raw_write_lock_bh+0xe0/0xe0
 ? __alloc_fd+0x10f/0x200
 do_sys_open+0x1db/0x2b0
 ? filp_open+0x50/0x50
 do_syscall_64+0x73/0x1b0
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fa7b24a4ca2
Code: 25 00 00 41 00 3d 00 00 41 00 74 4c 48 8d 05 85 7a 0d 00 8b 00 85 c0
75 6d 89 f2 b8 01 01 00 00 48 89 fe bf 9c ff ff ff 0f 05 <48> 3d 00 f0 ff ff
0f 87 a2 00 00 00 48 8b 4c 24 28 64 48 33 0c 25
RSP: 002b:00007fffbafb3af0 EFLAGS: 00000246 ORIG_RAX: 0000000000000101
RAX: ffffffffffffffda RBX: 000055d3648ade30 RCX: 00007fa7b24a4ca2
RDX: 0000000000000241 RSI: 000055d364a55240 RDI: 00000000ffffff9c
RBP: 00007fffbafb3bf0 R08: 0000000000000020 R09: 0000000000000002
R10: 00000000000001b6 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000003 R14: 0000000000000001 R15: 000055d364a55240
==================================================================

So remove the track_data_destroy() destroy_hist_field() call for that
var_ref.

Link: http://lkml.kernel.org/r/1deffec420f6a16d11dd8647318d34a66d1989a9.camel@linux.intel.com

Fixes: 466f4528 ("tracing: Generalize hist trigger onmax and save action")
Reported-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

So far we effectively clear the BMCR register. Some PHY's can deal
with this (e.g. because they reset BMCR to a default as part of a
soft-reset) whilst on others this causes issues because e.g. the
autoneg bit is cleared. Marvell is an example, see also thread [0].
So let's be a little bit more gentle and leave all bits we're not
interested in as-is. This change is needed for PHY drivers to
properly deal with the original patch.

[0] https://marc.info/?t=155264050700001&r=1&w=2

Fixes: 6e2d85ec ("net: phy: Stop with excessive soft reset")
Tested-by: Phil Reid <preid@electromag.com.au>
Tested-by: liweihang <liweihang@hisilicon.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 1aec4211.

Steven Rostedt reports that it causes a hang at bootup and bisected it
to this commit.

The troigger is apparently a module alias for "parport_lowlevel" that
points to "parport_pc", which causes a hang with

    modprobe -q -- parport_lowlevel

blocking forever with a backtrace like this:

    wait_for_completion_killable+0x1c/0x28
    call_usermodehelper_exec+0xa7/0x108
    __request_module+0x351/0x3d8
    get_lowlevel_driver+0x28/0x41 [parport]
    __parport_register_driver+0x39/0x1f4 [parport]
    daisy_drv_init+0x31/0x4f [parport]
    parport_bus_init+0x5d/0x7b [parport]
    parport_default_proc_register+0x26/0x1000 [parport]
    do_one_initcall+0xc2/0x1e0
    do_init_module+0x50/0x1d4
    load_module+0x1c2e/0x21b3
    sys_init_module+0xef/0x117

Supid says:
 "Due to the new device model daisy driver will now try to find the
  parallel ports while trying to register its driver so that it can bind
  with them. Now, since daisy driver is loaded while parport bus is
  initialising the list of parport is still empty and it tries to load
  the lowlevel driver, which has an alias set to parport_pc, now causes
  a deadlock"

But I don't think the daisy driver should be loaded by the parport
initialization in the first place, so let's revert the whole change.

If the daisy driver can just initialize separately on its own (like a
driver should), instead of hooking into the parport init sequence
directly, this issue probably would go away.
Reported-and-bisected-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Andreas reported that he was seeing the tdbtorture test fail in some
cases with -EDEADLCK when it wasn't before. Some debugging showed that
deadlock detection was sometimes discovering the caller's lock request
itself in a dependency chain.

While we remove the request from the blocked_lock_hash prior to
reattempting to acquire it, any locks that are blocked on that request
will still be present in the hash and will still have their fl_blocker
pointer set to the current request.

This causes posix_locks_deadlock to find a deadlock dependency chain
when it shouldn't, as a lock request cannot block itself.

We are going to end up waking all of those blocked locks anyway when we
go to reinsert the request back into the blocked_lock_hash, so just do
it prior to checking for deadlocks. This ensures that any lock blocked
on the current request will no longer be part of any blocked request
chain.

URL: https://bugzilla.kernel.org/show_bug.cgi?id=202975
Fixes: 5946c431 ("fs/locks: allow a lock request to block other requests.")
Cc: stable@vger.kernel.org
Reported-by: Andreas Schneider <asn@redhat.com>
Signed-off-by: Neil Brown <neilb@suse.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>