For "sram" debugfs file, if user did not specify the offset and length,
dump the entire data portion of sram by default.
Data portion is 0x800000 - 0x80ffff, but the actual data size is known
to the driver from the ucode file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Update the PCI_ID list for 5xx0 series.
Remove all the PCI_IDs which never made into production or not longer in
production.

Also make sure the supported bands(a/b/g/n) match specified PCI_IDs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since IO tracing is usually not needed and
generates a lot of data, separate it into
its own trace system so that we can always
enable iwlwifi:* and not have to worry about
getting too much data. If IO tracing is then
really needed we can enable iwlwifi_io:* in
addition and get that data.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

reserved2 field in "struct iwl4965_addsta_cmd" is __le16.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Dynamically allocate memory for dumping SRAM based on the length of memory
to be displayed.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For tx_queue, need to increase the buffer size allocated for it,
so all the queues information can be displayed
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Set the correct Read/Write file permission for iwlwifi debugfs files
based on the functionality of the files
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

LED blink rate is based on the traffic load, when tx/rx traffic counts
got reset, we also need to reset the led_tpt to prevent incorrect
blink rate being calculated.

Merge both clear_tx_statistics() and clear_rx_statistics() into
single clear_traffic_statistics() function, when reset the traffic byte
counts, both tx and rx need to be reset at the same time, to make
sure calculated the correct led blink rate.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Setting "Spatial multiplexing Power Save" as part of
per device configuration parameter.

Report to uCode based on priv->conf setting, so driver can
have more control of how different devices should operate
in power save mode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

LED blinking rate is based on tx/rx traffic, the most reasonable place
to do it is after update the traffic byte counts

This fixes the recent LED blinking breakage on 3945 introduced by "iwlwifi:
separate led function from statistic notification"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

CSR_INT_COALESCING previously had only one, but now has two single-byte fields.
With only one single-byte field (lowest order byte) it was okay to write via
iwl_write32(), but now with two, an iwl_write32() to the lower order field
clobbers the other field (odd-address CSR_INT_PERIODIC_REG, offset 0x5), and an
iwl_write32() to CSR_INT_PERIODIC_REG could clobber the lowest byte of the
next-higher register (CSR_INT, offset 0x8).

Fortunately, no bad side effects have been produced by the iwl_write32()
usage, due to order of execution (low order byte was always written before
higher order byte), and the fact that writing "0" to the low byte of the
next higher register has no effect (only action is when writing "1"s).

Nonetheless, this cleans up the accesses so no bad side effects might occur
in the future, if execution order changes, or more bit fields get added to
CSR_INT_COALESCING.

Add some comments regarding periodic interrupt usage.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To support byte writes to CSR_INT_COALESCING and CSR_INT_PERIODIC registers,
add iwl_write8(), including debug/trace support.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add a missing rcu_read_unlock() before jumping out
of the ieee80211_change_station() function in the
error case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The sign of correction coefficients was lost in the calculations, which
caused high packetloss in 802.11a mode after the results were applied.
Fixed by removing unneccesary and broken AND with a bit mask.
Signed-off-by: Lukas Turek <8an@praha12.net>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ieee80211_local.wstats is a remnant from the
days when we still had to worry about wireless
extensions in mac80211 -- it can be removed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This rewrites the error handling policies in the TX status handler.
It tries to be error-tolerant as in "try hard to not crash the machine".
It won't recover from errors (that are bugs in the firmware or driver),
because that's impossible. However, it will return a more or less useful
error message and bail out. It also tries hard to use rate-limited messages
to not flood the syslog in case of a failure.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It has been tested with a 802.11 frame generator and by checking the FCS field
of each received frame with the value reported by the Atheros hardware. This
patch is useful if you are trying to analyze non standard 802.11 frame going
over the air.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

At present, the results of an SSB core scan are only logged when
CONFIG_SSB_DEBUG is "y". As this may not be set in a distro kernel,
it is difficult interpret many problems posted in bug reports or in
help forums.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2200 is able to detect when it's been hard-killed, but doesn't update
the core rfkill state or update userspace. Ensure that the state is updated,
allowing the rfkill core to notify userspace.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libipw unconditionally calls wiphy_unregister, but it's up to the driver
to register it in the first place. ipw2100 fails to do so. Add the necessary
glue code, and also ensure that rfkill statuses get set up appropriately.

(Augmented for proper wiphy_unregister placement. -- JWL)
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Initiate the conversion of libipw to the new cfg80211 configuration API.

For now, leave CONFIG_IPW2200_PROMISCUOUS stuff alone.  Eventually
migrate it to cfg80211 when the add/del/change_virtual_intf methods
are implemented.

(v2: Fix unconditional wiphy_unregister in libipw which was causing
     problems for ipw2100, somewhat based on prior attempted fix
     by Zhu Yi <yi.zhu@intel.com>.  Previously both original version of
     this patch and Zhu Yi's fix attempt were reverted due to
     discovery of regressions. -- JWL)
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is sometimes useful to debug HT issues
as it shows what exactly the stack thinks
the peer supports.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With WEXT, it happens frequently that the SME
requests an authentication but then deauthenticates
right away because some new parameters came along.
Every time this happens we print a deauth message
and send a deauth frame, but both of that is rather
confusing. Avoid it by aborting the authentication
process silently, and telling cfg80211 about that.

The patch looks larger than it really is:
__cfg80211_auth_remove() is split out from
cfg80211_send_auth_timeout(), there's no new code
except __cfg80211_auth_canceled() (a one-liner) and
the mac80211 bits (7 new lines of code).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Right now all frames mac80211 hands to the driver
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set to
request TX status. This isn't really necessary, only
the injected frames need TX status (the latter for
hostapd) so move setting this flag.

The rate control algorithms also need TX status, but
they don't require it.

Also, rt2x00 uses that bit for its own purposes and
seems to require it being set for all frames, but
that can be fixed in rt2x00.

This doesn't really change anything for any drivers
but in the future drivers using hw-rate control may
opt to not report TX status for frames that don't
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com> [rt2x00 bits]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

A number of people have tried to add a wireless interface
(in managed mode) to a bridge and then complained that it
doesn't work. It cannot work, however, because in 802.11
networks all packets need to be acknowledged and as such
need to be sent to the right address. Promiscuous doesn't
help here. The wireless address format used for these
links has only space for three addresses, the
 * transmitter, which must be equal to the sender (origin)
 * receiver (on the wireless medium), which is the AP in
   the case of managed mode
 * the recipient (destination), which is on the APs local
   network segment

In an IBSS, it is similar, but the receiver and recipient
must match and the third address is used as the BSSID.

To avoid such mistakes in the future, disallow adding a
wireless interface to a bridge.

Felix has recently added a four-address mode to the AP
and client side that can be used (after negotiating that
it is possible, which must happen out-of-band by setting
up both sides) for bridging, so allow that case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It's very likely that not many devices will support
four-address mode in station or AP mode so introduce
capability bits for both modes, set them in mac80211
and check them when userspace tries to use the mode.
Also, keep track of 4addr in cfg80211 (wireless_dev)
and not in mac80211 any more. mac80211 can also be
improved for the VLAN case by not looking at the
4addr flag but maintaining the station pointer for
it correctly. However, keep track of use_4addr for
station mode in mac80211 to avoid all the derefs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We've accumulated a number of options for wiphys
which make more sense as flags as we keep adding
more. Convert the existing ones.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enforce all device constraints on the descriptor memory region.

There are several constraints on the descriptor memory, as documented
in the specification. The current code does not enforce them and/or
incorrectly enforces them.

Those constraints are:
- The address limitations on 30/32bit engines, that also apply to
  the skbs.
- The 4k alignment requirement on 30/32bit engines.
- The 8k alignment requirement on 64bit engines.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It's enough code to have its own file, I think.
Especially since I'm going to add to it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since the flags moved into skb->cb, there's no
longer a need to have the encrypt bool passed
into the function, anyone who requires it set
to 0 (false) can just set the flag directly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Janakiram Sistla <janakiram.sistla@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Janakiram Sistla <janakiram.sistla@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/wl3501_cs.c: In function ‘wl3501_esbq_exec’:
drivers/net/wireless/wl3501_cs.c:387: warning: ‘tmp’ is used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:384: note: ‘tmp’ was declared here
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When going from/to a WEP protected IBSS, we need to
leave this one and join a new one to take care of
the changed capability.

Cc: Hong Zhang <henryzhang62@yahoo.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Not assigning the vif pointer causes an oops.
This patch fixes it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211 rejects all association requests when in associated state. This
prevents clean roaming within an ESS since one would first need to
disassociate before being able to request reassociation.

Accept the reassociation request and let the old association to be
dropped when the new one is completed. This fixes nl80211-based
roaming with the current snapshot version of wpa_supplicant (that has
code for requesting reassociation explicitly withthe previous BSSID
attribute).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>