Remove OMAP_DSS_LCD_TFT as a omap_panel_config flag.

We don't support passive matrix displays any more. Remove this flag from all the
panel drivers.

Force the display_type to OMAP_DSS_LCD_DISPLAY_TFT in the interface drivers.
Signed-off-by: Archit Taneja <archit@ti.com>

Remove clock constraints related to passive matrix displays.

There is a constraint (pcd_min should be 3) for passive matrix displays. Remove
this constraint in clock divider calculations as we won't support passive
matrix displays any more.

This cleans up the functions which calculate the clock dividers with DSI's PLL
or DSS_FCLK as the clock source.
Signed-off-by: Archit Taneja <archit@ti.com>

State change of HDMI PHY could potentially take many millisecs, we can do
better by protecting things in hdmi_set_phy_pwr() with a mutex rather than
a spin_lock_irqsave.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

It is simpler to read the current status from a register as compared
to maintaining a state variable to hold the information.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

DISPC functions have been modified to provide clock and register dumps and debug
support for the LCD3 manager.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The support for LCD3 manager has been added into the manager module. LCD3 panel
has registers as DISPC_CONTROL3 and DISPC_CONFIG3 just like those in LCD and
LCD2 panels. These registers control the Display Controller (DISPC) module for
LCD3 output. The three LCDs support Display Serial Interface (DSI), Remote Frame
Buffer Interface (RFBI) and Parallel CMOS Output Interface (DPI). These LCDs can
be connected through parallel output interface using DISPC and RFBI or DPI. For
serial interface DSS uses DSI.

The LCD3 panel, just like LCD and LCD2 panels, has a clock switch in DSS_CTRL
register which has been enabled. The clock switch chooses between DSS_CLK and
DPLL_DSI1_C_CLK1 as source for LCD3_CLK. New IRQs as DISPC_IRQ_VSYNC3,
DISPC_IRQ_FRAMEDONE3, DISPC_IRQ_ACBIAS_COUNT_STAT3 and DISPC_IRQ_SYNC_LOST3 have
been added specific to the new manager.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

OMAP5 Display Subsystem (DSS) architecture comes with a additional LCD3 channel
with its own dedicated overlay manager. The current patch adds LCD3 channel and
basic register support for LCD3 channel. It adds register addresses for various
Display Controller (DISPC) registers like DISPC_DEFAULT_COLOR, DISPC_TIMING_H,
DISPC_DIVISORo, etc.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The current implementation of LCD channels and managers consists of a number of
if-else construct which has been replaced by a simpler interface. A constant
structure mgr_desc has been created in Display Controller (DISPC) module. The
mgr_desc contains for each channel its name, irqs and  is initialized one time
with all registers and their corresponding fields to be written to enable
various features of Display Subsystem. This structure is later used by various
functions of DISPC which simplifies the further implementation of LCD channels
and its corresponding managers.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

If runtime PM is not enabled in the kernel config, pm_runtime_get_sync()
will always return 1 and pm_runtime_put_sync() will always return
-ENOSYS. pm_runtime_get_sync() returning 1 presents no problem to the
driver, but -ENOSYS from pm_runtime_put_sync() causes the driver to
print a warning.

One option would be to ignore errors returned by pm_runtime_put_sync()
totally, as they only say that the call was unable to put the hardware
into suspend mode.

However, I chose to ignore the returned -ENOSYS explicitly, and print a
warning for other errors, as I think we should get notified if the HW
failed to go to suspend properly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Grazvydas Ignotas <notasas@gmail.com>

The current way how omapdss handles system suspend and resume is that
omapdss device (a platform device, which is not part of the device
hierarchy of the DSS HW devices, like DISPC and DSI, or panels.) uses
the suspend and resume callbacks from platform_driver to handle system
suspend. It does this by disabling all enabled panels on suspend, and
resuming the previously disabled panels on resume.

This presents a few problems.

One is that as omapdss device is not related to the panel devices or the
DSS HW devices, there's no ordering in the suspend process. This means
that suspend could be first ran for DSS HW devices and panels, and only
then for omapdss device. Currently this is not a problem, as DSS HW
devices and panels do not handle suspend.

Another, more pressing problem, is that when suspending or resuming, the
runtime PM functions return -EACCES as runtime PM is disabled during
system suspend. This causes the driver to print warnings, and operations
to fail as they think that they failed to bring up the HW.

This patch changes the omapdss suspend handling to use PM notifiers,
which are called before suspend and after resume. This way we have a
normally functioning system when we are suspending and resuming the
panels.

This patch, I believe, creates a problem that somebody could enable or
disable a panel between PM_SUSPEND_PREPARE and the system suspend, and
similarly the other way around in resume. I choose to ignore the problem
for now, as it sounds rather unlikely, and if it happens, it's not
fatal.

In the long run the system suspend handling of omapdss and panels should
be thought out properly. The current approach feels rather hacky.
Perhaps the panel drivers should handle system suspend, or the users of
omapdss (omapfb, omapdrm) should handle system suspend.

Note that after this patch we could probably revert
0eaf9f52 (OMAPDSS: use sync versions of
pm_runtime_put). But as I said, this patch may be temporary, so let's
leave the sync version still in place.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Jassi Brar <jaswinder.singh@linaro.org>
Tested-by: Jassi Brar <jaswinder.singh@linaro.org>

In preparation of OMAP moving to Common Clk Framework(CCF) change
clk_enable() and clk_disable() calls to clk_prepare_enable() and
clk_disable_unprepare() in omapdss. This can be safely done, as omapdss
never enables or disables clocks in atomic context.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: <linux-fbdev@vger.kernel.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>
[tomi.valkeinen@ti.com: updated patch description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

We have two almost the same enums: omap_channel and
omap_dss_overlay_managers. omap_channel is used almost everywhere, and
omap_channel assigns explicit values to the enum values which are needed
for proper operation.

omap_dss_overlay_managers is only used in one place, so it's easy to
remove it, which is what this patch does.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Merge v3.5-rc2 to get latest device tree and dynamic debug changes.

If the privileges given to root threads (3% of allowable memory) or a
negative value of /proc/pid/oom_score_adj happen to exceed the amount of
rss of a thread, its badness score overflows as a result of commit
a7f638f9 ("mm, oom: normalize oom scores to oom_score_adj scale only
for userspace").

Fix this by making the type signed and return 1, meaning the thread is
still eligible for kill, if the value is negative.
Reported-by: Dave Jones <davej@redhat.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull scheduler fixes from Ingo Molnar.

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix the relax_domain_level boot parameter
  sched: Validate assumptions in sched_init_numa()
  sched: Always initialize cpu-power
  sched: Fix domain iteration
  sched/rt: Fix lockdep annotation within find_lock_lowest_rq()
  sched/numa: Load balance between remote nodes
  sched/x86: Calculate booted cores after construction of sibling_mask

Fix lots of new kernel-doc warnings in kernel/sched/fair.c:

  Warning(kernel/sched/fair.c:3625): No description found for parameter 'env'
  Warning(kernel/sched/fair.c:3625): Excess function parameter 'sd' description in 'update_sg_lb_stats'
  Warning(kernel/sched/fair.c:3735): No description found for parameter 'env'
  Warning(kernel/sched/fair.c:3735): Excess function parameter 'sd' description in 'update_sd_pick_busiest'
  Warning(kernel/sched/fair.c:3735): Excess function parameter 'this_cpu' description in 'update_sd_pick_busiest'
  .. more warnings
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit 9e612a00.

It incorrectly finds VGA connectors where none are attached, apparently
not noticing that nothing replied to the EDID queries, and happily using
the default EDID modes that have nothing to do with actual hardware.

That in turn then causes X to fall down to the lowest common
denominator, which is usually the default 1024x768 mode that is in the
default EDID and pretty much anything supports).

I'd suggest that if not relying on the HDP pin, the code should at least
check whether it gets valid EDID data back, rather than just assume
there's something on the VGA connector.

Cc: Dave Airlie <airlied@linux.ie>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ext4 bug fixes from Theodore Ts'o:
 "This update contains two bug fixes, both destined for the stable tree.
  Perhaps the most important is one which fixes ext4 when used with file
  systems originally formatted for use with ext3, but then later
  converted to take advantage of ext4."

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: don't set i_flags in EXT4_IOC_SETFLAGS
  ext4: fix the free blocks calculation for ext3 file systems w/ uninit_bg

Pull powerpc fixes from Paul Mackerras:
 "Two small fixes for powerpc:
   - a fix for a regression since 3.2 that causes 4-second (or longer)
     pauses
   - a fix for a potential oops when loading kernel modules on 32-bit
     embedded systems."

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  powerpc: Fix kernel panic during kernel module load
  powerpc/time: Sanity check of decrementer expiration is necessary

Pull UBI/UBIFS fixes from Artem Bityutskiy:
 "Fix UBI and UBIFS - they refuse to work without debugfs.  This was
  broken by the 3.5-rc1 UBI/UBIFS changes when we removed the debugging
  Kconfig switches.

  Also, correct locking in 'ubi_wl_flush()' - it was extended to support
  flushing a specific LEB in 3.5-rc1, and the locking was sub-optimal."

* tag 'upstream-3.5-rc2' of git://git.infradead.org/linux-ubifs:
  UBI: correct ubi_wl_flush locking
  UBIFS: fix debugfs-less systems support
  UBI: fix debugfs-less systems support

This reverts commit 7732a557 (and commit
3f50fff4, which was a follow-up
cleanup).

We're chasing an elusive bug that Dave Jones can apparently reproduce
using his system call fuzzer tool, and that looks like some kind of
locking ordering problem on the directory i_mutex chain.  Our i_mutex
locking is rather complex, and depends on the topological ordering of
the directories, which is why we have been very wary of splicing
directory entries around.

Of course, we really don't want to ever see aliased unconnected
directories anyway, so none of this should ever happen, but this revert
aims to basically get us back to a known older state.

Bruce points to some of the previous discussion at

       http://marc.info/?i=<20110310105821.GE22723@ZenIV.linux.org.uk>

and in particular a long post from Neil:

       http://marc.info/?i=<20110311150749.2fa2be66@notabene.brown>

It should be noted that it's possible that Dave's problems come from
other changes altohgether, including possibly just the fact that Dave
constantly is teachning his fuzzer new tricks.  So what appears to be a
new bug could in fact be an old one that just gets newly triggered, but
reverting these patches as "still under heavy discussion" is the right
thing regardless.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: J. Bruce Fields <bfields@fieldses.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull x86 fixes from Ingo Molnar.

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/nmi: Fix section mismatch warnings on 32-bit
  x86/uv: Fix UV2 BAU legacy mode
  x86/mm: Only add extra pages count for the first memory range during pre-allocation early page table space
  x86, efi stub: Add .reloc section back into image
  x86/ioapic: Fix NULL pointer dereference on CPU hotplug after disabling irqs
  x86/reboot: Fix a warning message triggered by stop_other_cpus()
  x86/intel/moorestown: Change intel_scu_devices_create() to __devinit
  x86/numa: Set numa_nodes_parsed at acpi_numa_memory_affinity_init()
  x86/gart: Fix kmemleak warning
  x86: mce: Add the dropped timer interval init back
  x86/mce: Fix the MCE poll timer logic

Pull perf fixes from Ingo Molnar:
 "A bit larger than what I'd wish for - half of it is due to hw driver
  updates to Intel Ivy-Bridge which info got recently released,
  cycles:pp should work there now too, amongst other things.  (but we
  are generally making exceptions for hardware enablement of this type.)

  There are also callchain fixes in it - responding to mostly
  theoretical (but valid) concerns.  The tooling side sports perf.data
  endianness/portability fixes which did not make it for the merge
  window - and various other fixes as well."

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
  perf/x86: Check user address explicitly in copy_from_user_nmi()
  perf/x86: Check if user fp is valid
  perf: Limit callchains to 127
  perf/x86: Allow multiple stacks
  perf/x86: Update SNB PEBS constraints
  perf/x86: Enable/Add IvyBridge hardware support
  perf/x86: Implement cycles:p for SNB/IVB
  perf/x86: Fix Intel shared extra MSR allocation
  x86/decoder: Fix bsr/bsf/jmpe decoding with operand-size prefix
  perf: Remove duplicate invocation on perf_event_for_each
  perf uprobes: Remove unnecessary check before strlist__delete
  perf symbols: Check for valid dso before creating map
  perf evsel: Fix 32 bit values endianity swap for sample_id_all header
  perf session: Handle endianity swap on sample_id_all header data
  perf symbols: Handle different endians properly during symbol load
  perf evlist: Pass third argument to ioctl explicitly
  perf tools: Update ioctl documentation for PERF_IOC_FLAG_GROUP
  perf tools: Make --version show kernel version instead of pull req tag
  perf tools: Check if callchain is corrupted
  perf callchain: Make callchain cursors TLS
  ...

Pull drm intel and exynos fixes from Dave Airlie:
 "A bunch of fixes for Intel and exynos, nothing too major, a new intel
  PCI ID, and a fix for CRT detection."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: pch_irq_handler -> {ibx, cpt}_irq_handler
  char/agp: add another Ironlake host bridge
  drm/i915: fix up ivb plane 3 pageflips
  drm/exynos: fixed blending for hdmi graphic layer
  drm/exynos: Remove dummy encoder get_crtc operation implementation
  drm/exynos: Keep a reference to frame buffer GEM objects
  drm/exynos: Don't cast GEM object to Exynos GEM object when not needed
  drm/exynos: DRIVER_BUS_PLATFORM is not a driver feature
  drm/exynos: fixed size type.
  drm/exynos: Use DRM_FORMAT_{NV12, YUV420} instead of DRM_FORMAT_{NV12M, YUV420M}
  drm/i915: hold forcewake around ring hw init
  drm/i915: Mark the ringbuffers as being in the GTT domain
  drm/i915/crt: Do not rely upon the HPD presence pin
  drm/i915: Reset last_retired_head when resetting ring

Pull leap second timer fix from Thomas Gleixner.

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Fix CLOCK_MONOTONIC inconsistency during leapsecond

Merge tag 'moduleparam-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus

Pull minor module param fixes from Rusty Russell:
 "One bugfix for multiple moduleparam levels, one removal of overzealous
  printk."

* tag 'moduleparam-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  init: Drop initcall level output
  module_param: stop double-calling parameters.

It was reported that compiling for 32-bit caused a bunch of
section mismatch warnings:

 VDSOSYM arch/x86/vdso/vdso32-syms.lds
  LD      arch/x86/vdso/built-in.o
  LD      arch/x86/built-in.o

 WARNING: arch/x86/built-in.o(.data+0x5af0): Section mismatch in
 reference from the variable test_nmi_ipi_callback_na.10451 to
 the function .init.text:test_nmi_ipi_callback() [...]

 WARNING: arch/x86/built-in.o(.data+0x5b04): Section mismatch in
 reference from the variable nmi_unk_cb_na.10399 to the function
 .init.text:nmi_unk_cb() The variable nmi_unk_cb_na.10399
 references the function __init nmi_unk_cb() [...]

Both of these are attributed to the internal representation of
the nmiaction struct created during register_nmi_handler.  The
reason for this is that those structs are not defined in the
init section whereas the rest of the code in nmi_selftest.c is.

To resolve this, I created a new #define,
register_nmi_handler_initonly, that tags the struct as
__initdata to resolve the mismatch.  This #define should only be
used in rare situations where the register/unregister is called
during init of the kernel.

Big thanks to Jan Beulich for decoding this for me as I didn't
have a clue what was going on.
Reported-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Tested-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Cc: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Link: http://lkml.kernel.org/r/1338991542-23000-1-git-send-email-dzickus@redhat.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

This fixes a problem which can causes kernel oopses while loading
a kernel module.

According to the PowerPC EABI specification, GPR r11 is assigned
the dedicated function to point to the previous stack frame.
In the powerpc-specific kernel module loader, do_plt_call()
(in arch/powerpc/kernel/module_32.c), GPR r11 is also used
to generate trampoline code.

This combination crashes the kernel, in the case where the compiler
chooses to use a helper function for saving GPRs on entry, and the
module loader has placed the .init.text section far away from the
.text section, meaning that it has to generate a trampoline for
functions in the .init.text section to call the GPR save helper.
Because the trampoline trashes r11, references to the stack frame
using r11 can cause an oops.

The fix just uses GPR r12 instead of GPR r11 for generating the
trampoline code.  According to the statements from Freescale, this is
safe from an EABI perspective.

I've tested the fix for kernel 2.6.33 on MPC8541.

Cc: stable@vger.kernel.org
Signed-off-by: Steffen Rumler <steffen.rumler.ext@nsn.com>
[paulus@samba.org: reworded the description]
Signed-off-by: Paul Mackerras <paulus@samba.org>

The SGI Altix UV2 BAU (Broadcast Assist Unit) as used for
tlb-shootdown (selective broadcast mode) always uses UV2
broadcast descriptor format. There is no need to clear the
'legacy' (UV1) mode, because the hardware always uses UV2 mode
for selective broadcast.

But the BIOS uses general broadcast and legacy mode, and the
hardware pays attention to the legacy mode bit for general
broadcast. So the kernel must not clear that mode bit.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/E1SccoO-0002Lh-Cb@eag09.americas.sgi.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

x86/mm: Only add extra pages count for the first memory range during pre-allocation early page table space

Robin found this regression:

| I just tried to boot an 8TB system.  It fails very early in boot with:
| Kernel panic - not syncing: Cannot find space for the kernel page tables

git bisect commit 722bc6b1.

A git revert of that commit does boot past that point on the 8TB
configuration.

That commit will add up extra pages for all memory range even
above 4g.

Try to limit that extra page count adding to first entry only.
Bisected-by: Robin Holt <holt@sgi.com>
Tested-by: Robin Holt <holt@sgi.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/CAE9FiQUj3wyzQxtq9yzBNc9u220p8JZ1FYHG7t%3DMOzJ%3D9BZMYA@mail.gmail.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

Merge branch 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-samsung into drm-fixes

* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-samsung:
  drm/exynos: fixed blending for hdmi graphic layer
  drm/exynos: Remove dummy encoder get_crtc operation implementation
  drm/exynos: Keep a reference to frame buffer GEM objects
  drm/exynos: Don't cast GEM object to Exynos GEM object when not needed
  drm/exynos: DRIVER_BUS_PLATFORM is not a driver feature
  drm/exynos: fixed size type.
  drm/exynos: Use DRM_FORMAT_{NV12, YUV420} instead of DRM_FORMAT_{NV12M, YUV420M}

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: pch_irq_handler -> {ibx, cpt}_irq_handler
  char/agp: add another Ironlake host bridge
  drm/i915: fix up ivb plane 3 pageflips
  drm/i915: hold forcewake around ring hw init
  drm/i915: Mark the ringbuffers as being in the GTT domain
  drm/i915/crt: Do not rely upon the HPD presence pin
  drm/i915: Reset last_retired_head when resetting ring

9fb48c74 ("params: add 3rd arg to option handler callback
signature") added similar lines to dmesg:

initlevel:0=early, 4 registered initcalls
initlevel:1=core, 31 registered initcalls
initlevel:2=postcore, 11 registered initcalls
initlevel:3=arch, 7 registered initcalls
initlevel:4=subsys, 40 registered initcalls
initlevel:5=fs, 30 registered initcalls
initlevel:6=device, 250 registered initcalls
initlevel:7=late, 35 registered initcalls

but they don't contain any info for the general user staring at dmesg.
I'm very doubtful the count of initcalls registered per level helps
anyone so drop that output completely.

Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Commit 026cee00 "params:
<level>_initcall-like kernel parameters" set old-style module
parameters to level 0.  And we call those level 0 calls where we used
to, early in start_kernel().

We also loop through the initcall levels and call the levelled
module_params before the corresponding initcall.  Unfortunately level
0 is early_init(), so we call the standard module_param calls twice.

(Turns out most things don't care, but at least ubi.mtd does).

Change the level to -1 for standard module_param calls.
Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org

This reverts 68568add ("powerpc/time: Remove unnecessary sanity check
of decrementer expiration").  We do need to check whether we have reached
the expiration time of the next event, because we sometimes get an early
decrementer interrupt, most notably when we set the decrementer to 1 in
arch_irq_work_raise().  The effect of not having the sanity check is that
if timer_interrupt() gets called early, we leave the decrementer set to
its maximum value, which means we then don't get any more decrementer
interrupts for about 4 seconds (or longer, depending on timebase
frequency).  I saw these pauses as a consequence of getting a stray
hypervisor decrementer interrupt left over from exiting a KVM guest.

This isn't quite a straight revert because of changes to the surrounding
code, but it restores the same algorithm as was previously used.

Cc: stable@vger.kernel.org
Acked-by: Anton Blanchard <anton@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This reverts commit 40af1bbd.

It's horribly and utterly broken for at least the following reasons:

 - calling sync_mm_rss() from mmput() is fundamentally wrong, because
   there's absolutely no reason to believe that the task that does the
   mmput() always does it on its own VM.  Example: fork, ptrace, /proc -
   you name it.

 - calling it *after* having done mmdrop() on it is doubly insane, since
   the mm struct may well be gone now.

 - testing mm against NULL before you call it is insane too, since a
NULL mm there would have caused oopses long before.

.. and those are just the three bugs I found before I decided to give up
looking for me and revert it asap.  I should have caught it before I
even took it, but I trusted Andrew too much.

Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 79906964 uses the ext4_{set,clear}_inode_flags() functions to
change the i_flags automatically but fails to remove the error setting
of i_flags.  So we still have the problem of trashing state flags.
Fix this by removing the assignment.
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org

Ext3 filesystems that are converted to use as many ext4 file system
features as possible will enable uninit_bg to speed up e2fsck times.
These file systems will have a native ext3 layout of inode tables and
block allocation bitmaps (as opposed to ext4's flex_bg layout).
Unfortunately, in these cases, when first allocating a block in an
uninitialized block group, ext4 would incorrectly calculate the number
of free blocks in that block group, and then errorneously report that
the file system was corrupt:

EXT4-fs error (device vdd): ext4_mb_generate_buddy:741: group 30, 32254 clusters in bitmap, 32258 in gd

This problem can be reproduced via:

    mke2fs -q -t ext4 -O ^flex_bg /dev/vdd 5g
    mount -t ext4 /dev/vdd /mnt
    fallocate -l 4600m /mnt/test

The problem was caused by a bone headed mistake in the check to see if a
particular metadata block was part of the block group.

Many thanks to Kees Cook for finding and bisecting the buggy commit
which introduced this bug (commit fd034a84, present since v3.2).
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Reported-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tested-by: Kees Cook <keescook@chromium.org>
Cc: stable@kernel.org