New architecture and board configuration support for m68knommu.

. add 523x ColdFire support
. add support for SOM5282 and MOD5272 boards
. break up the 527x to be separate 5271 and 5275. There is some
  subtle differences that (like RAM config) that need to be dealt with
. add option to support selecting 4k kernel stack
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Add support for the 523x ColdFire family of processors
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Make show_stack() consistent with other architectures.
Put the vector string names in the .rodata section.
Patch originally submitted by Philippe De Muyter <phdm@macqel.be>.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Modify maintainers for uClinux (MMUless). Neither Dave nor Jeff
manitain the 2.6 code in mainline, so no point emailing them about
problems.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Correctly determine the end of ram for ram setups that do not
start at base address of 0. Add support for the MOD5272 board,
which doesn not have a ram base of 0.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

. setup for the new 523x ColdFire family
. break up of 527x to be 5271 and 5275
. some white space cleanup
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Low level initialization code for the 523x ColdFire processor family.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Merge refs/heads/ieee80211-wifi from master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6 

We weren't explicitly setting the page table bits we desired
in user_prot in the protection table, which resulted in the
user mappings for v6 CPUs being marked global.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We run into problems if we blindly enable L2 prefetching without
checking that the L2 cache is actually enabled.  Additionaly, if we
disable the L2 cache we need to ensure that we disable L2 prefetching.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This fixes a problem with pci_map_rom() which doesn't properly
update the ROM BAR value with the address thas allocated for it by the
PCI code. This problem, among other, breaks boot on Mac laptops.

It'ss a new version based on Linus latest one with better error
checking.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

In adjusting the logic for SLB miss for the dynamic hugepage stuff, I
messed up the !CONFIG_HUGETLB_PAGE case, failing to set the SLB flags
properly.

This fixes it.  It also streamlines the logic for the HUGETLB_PAGE case
(removing a couple of branches) while we're at it.

Booted, and roughly tested on POWER5 (with and without HUGETLB_PAGE),
iSeries/RS64 (no hugepage available), and G5 (with and without
HUGETLB_PAGE).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This fixes the following compile error:

	...
	  LD      .tmp_vmlinux1
	drivers/built-in.o: In function `frontend_init':
	budget-av.c:(.text+0xb9448): undefined reference to `tda10046_attach'
	budget-av.c:(.text+0xb9518): undefined reference to `tda10021_attach'
	drivers/built-in.o: In function `philips_tu1216_request_firmware':
	budget-av.c:(.text+0xb937b): undefined reference to `request_firmware'
	make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Johannes Stezenbach <js@linuxtv.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

No point checking what CPU architecture level we have each time
within the loop, so precompute the base PMD flags outside the
loop.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

The prototype for sys_fadvise64_64() is:
    long sys_fadvise64_64(int fd, loff_t offset, loff_t len, int advice)
The argument list is therefore as follows on legacy ABI:
	fd: type int (r0)
	offset: type long long (r1-r2)
	len: type long long (r3-sp[0])
	advice: type int (sp[4])
With EABI this becomes:
	fd: type int (r0)
	offset: type long long (r2-r3)
	len: type long long (sp[0]-sp[4])
	advice: type int (sp[8])
Not only do we have ABI differences here, but the EABI version requires
one additional word on the syscall stack.
To avoid the ABI mismatch and the extra stack space required with EABI
this syscall is now defined with a different argument ordering
on ARM as follows:
    long sys_arm_fadvise64_64(int fd, int advice, loff_t offset, loff_t len)
This gives us the following ABI independent argument distribution:
	fd: type int (r0)
	advice: type int (r1)
	offset: type long long (r2-r3)
	len: type long long (sp[0]-sp[4])
Now, since the syscall entry code takes care of 5 registers only by
default including the store of r4 to the stack, we need a wrapper to
store r5 to the stack as well.  Because that wrapper was missing and was
always required this means that sys_fadvise64_64 never worked on ARM and
therefore we can safely reuse its syscall number for our new
sys_arm_fadvise64_64 interface.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

local->hw_priv was initialized only after the interrupt handler was
registered. This could trigger a NULL pointer dereference in
prism2_pccard_card_present() that assumed that local->hw_priv is always
set (and it should have been). Fix this by setting local->hw_priv before
registering the interrupt handler.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

The iseries_veth driver tells sysfs that it's called 'iseries_veth', but if
you ask it via ethtool it thinks it's called 'veth'. I think this comes from
2.4 when the driver was called 'veth', but it's definitely called
'iseries_veth' now, so fix it.

To make sure we don't do it again define DRV_NAME and use it everywhere.

While we're at it, change the version number to 2.0, to reflect the changes
made in this patch series.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Having merged iseries_veth.h, let's remove some of the studly caps that came
with it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

iseries_veth.h is only used by iseries_veth.c, so merge the former into
the latter.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Also to aid debugging, add sysfs support for iseries_veth's port structures.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

To aid in field debugging, add sysfs support for iseries_veth's connection
structures. At the moment this is all read-only, however we could think about
adding write support for some attributes in future.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

There's a number of problems with the way iseries_veth counts TX errors.

Firstly it counts conditions which aren't really errors as TX errors. This
includes if we don't have a connection struct for the other LPAR, or if the
other LPAR is currently down (or just doesn't want to talk to us). Neither
of these should count as TX errors.

Secondly, it counts one TX error for each LPAR that fails to accept the packet.
This can lead to TX error counts higher than the total number of packets sent
through the interface. This is confusing for users.

This patch fixes that behaviour. The non-error conditions are no longer
counted, and we introduce a new and I think saner meaning to the TX counts.

If a packet is successfully transmitted to any LPAR then it is transmitted
and tx_packets is incremented by 1.

If there is an error transmitting a packet to any LPAR then that is counted
as one error, ie. tx_errors is incremented by 1.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

The iseries_veth driver often has multiple netdevices sending packets over
a single connection to another LPAR. If the bandwidth to the other LPAR is
exceeded, all the netdevices must have their queues stopped.

The current code achieves this by queueing one incoming skb on the
per-netdevice port structure. When the connection is able to send more packets
we iterate through the port structs and flush any packet that is queued,
as well as restarting the associated netdevice's queue.

This arrangement makes less sense now that we have per-connection TX timers,
rather than the per-netdevice generic TX timer.

The new code simply detects when one of the connections is full, and stops
the queue of all associated netdevices. Then when a packet is acked on that
connection (ie. there is space again) all the queues are woken up.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Currently the iseries_veth driver contravenes the specification in
Documentation/networking/driver.txt, in that if packets are not acked by
the other LPAR they will sit around forever.

This patch adds a per-connection timer which fires if we've had no acks for
five seconds. This is superior to the generic TX timer because it catches
the case of a small number of packets being sent and never acked.

This fixes a bug we were seeing on real systems, where some IPv6 neighbour
discovery packets would not be acked and then prevent the module from being
removed, due to skbs lying around.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

The iseries_veth driver uses the generic TX timeout watchdog, however a better
solution is in the works, so remove this code.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

The iseries_veth driver can attach to multiple vlans, which correspond to
multiple net devices. However there is only 1 connection between each LPAR,
so the connection structure may be shared by multiple net devices.

This makes module removal messy, because we can't deallocate the connections
until we know there are no net devices still using them. The solution is to
use ref counts on the connections, so we can delete them (actually stop) as
soon as the ref count hits zero.

This patch fixes (part of) a bug we were seeing with IPv6 sending probes to
a dead LPAR, which would then hang us forever due to leftover skbs.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

This patch makes veth_init_connection() and veth_destroy_connection()
symmetrical in that they allocate/deallocate the same data.

Currently if there's an error while initialising connections (ie. ENOMEM)
we call veth_module_cleanup(), however this will oops because we call
driver_unregister() before we've called driver_register(). I've never seen
this actually happen though.

So instead we explicitly call veth_destroy_connection() for each connection,
any that have been set up will be deallocated.

We also fix a potential leak if vio_register_driver() fails.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>