This patch fixes the buffer overflow warning by refactoring
hclgevf_bind_ring_to_vector and hclge_get_ring_chain_from_mbx.

Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Fixes: dde1a86e ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When vlan ctag filter is enabled, the loopback selftest fails because
loopback selftest does not support vlan.

This patch fixes it by disabling the vlan ctag filter when runnig
loopback selftest.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add support for querying pfc puase packets statistic
in hclge_ieee_getpfc, which is used to tell user how many pfc
puase packets have been sent and received by this mac port.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Original skb->truesize reports the received packet size,
not the actual buffer size NIC driver allocated(1 Page).
The linux net protocol will misjudge the true size of rx queue.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the firmware cmd to setup mac pause params is the same as the
firmware cmd to pfc pause params, this patch unifies the pause params
setup function.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function of dev_close and dev_open is just likes ifconfig <netif> down
and ifconfig <netif> up. The ipv6 address will be lost after dev_close and
dev_open are called. This patch uses hns3_nic_net_stop to replace dev_close
and uses hns3_nic_net_open to replace dev_open.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The link status update function is called by timer every second. But
net_stop and net_open may be called with very short intervals. The link
status update function can not detect the link state has changed. It
causes the netdev not running problem.

This patch fixes it by updating the link state in ae_stop function.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When driver is in initial state, the mac_vlan table table is empty.
So the delete operation for mac address must fail. Existence check
is needed here. Otherwise, the error message will make user confused.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
selftests: forwarding: Tweaks and a new test

First patch adds a new test for VLAN-unaware bridges.

Next two patches make the tests fail in case they are missing interfaces
or dependencies.

Last patch allows one to create the veth interfaces even without the
optional configuration file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Some users want to be able to run the tests without a configuration file
which is useful when one needs to test both virtual and physical
interfaces on the same machine.

Move the defines that set the type of interface to create and whether to
create it away from the optional configuration file to the library like
the rest of the defines.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Returning 0 gives a false sense of success when the required modules did
not even manage to be initialized and register the required net devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We already return an error when some dependencies (e.g., 'jq') are
missing so lets be consistent and do that for all.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to the VLAN-aware bridge test, test the VLAN-unaware bridge and
make sure that ping, FDB learning and flooding work as expected.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2018-03-09

here is the current pile of qeth patches for net-next. Just the usual
small updates and clean ups. Please apply.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Using up 8 bytes in every ipaddr object to store SETIP/DELIP flags is
rather wasteful. Except for takeover eligibility, the flag values all
just depend on the address type, so determine them on demand.

While at it reorder the struct to fill an alignment hole.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reduce code duplication.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On an IP event, current code tries to determine if the netdev belongs
to a L3 card by walking all qeth cards in the system, and then all of
their VLAN devices too. Short-cut the whole thing by identifying a L3
device through its netdev_ops.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extract a helper that does the actual work & returns the right NOTIFY_*
responses, and start putting the temporary ipaddr container objects
on the stack rather than kmalloc'ing them. They are small, and this
reduces the confusion of which objects actually get added to qeth's
IP tables.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

init_qdio_queues() resets the Input Queue's overall QDIO state, and
positions the buffer cursor back to 0. So this is the obvious place to
also reset the queue's NAPI context (in contrast to doing it rather
randomly in the middle of the big set_online() path).
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Newly-allocated skbs default to PACKET_HOST, and eth_type_trans() is
smart enough to determine any other packet type from the frame's
destination address.
So except for the IQD sniffer case, there is no need to set up
skb->pkt_type manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

napi_alloc_skb() doesn't need to disable IRQs during the allocation,
and thus may save us a few cycles.
Doing so requires a small fix-up in the HiperTransport path, which
currently assumes a fixed NET_SKB_PAD headroom padding. napi_alloc_skb()
adds an additional NET_IP_ALIGN padding, so use the proper helper for
setting up the mac_header offset.

Use this opportunity to convert the non-NAPI path to netdev_alloc_skb(),
which means that skb->dev is now always set-up during allocation and
doesn't need to be assigned manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to pass the *payload* length, not the L2 address length.
For qeth (using eth_header()) this is merely a cosmetic change:
the parameter only matters when building headers for ETH_P_802_2
or ETH_P_802_3, whereas our fake headers are built with
ETH_P_IP / ETH_P_IPV6 / 0.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth implements HW-based Unicast Filtering (via SETVMAC) on L2 devices.
Tell the stack, so it knows that receiving traffic for secondary
addresses doesn't require full-blown promiscuous mode.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NETIF_F_SG support is currently limited to OSA (and for L2 even OSD)
devices. Advertise it for some more device types (OSM, L2 OSX, z/VM OSA)
that share the same code paths. For now, keep it switched off by
default on these devices.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 'portname' attribute is deprecated and setting it has no effect.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"s390/qeth: fix SETIP command handling" introduced a new helper, apply
it driver-wide.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some network devices - notably ipvlan slave - are not compatible with
any kind of rx_handler. Currently the hook can be installed but any
configuration (bridge, bond, macsec, ...) is nonfunctional.

This change allocates a priv_flag bit to mark such devices and explicitly
forbid installing a rx_handler if such bit is set. The new bit is used
by ipvlan slave device.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

T6 cards can support up to 100 G speeds. So, increase
max programmable tx rate limit to 100 Gbps.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wvla, remove VLA usage and replace it
with a fixed-length array instead.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed a coding style issue.
Signed-off-by: Vaibhav Murkute <vaibhavmurkute88@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Peng Li says:

====================
fixes for configuration lost problems

This patchset refactors some functions and some bugs in order
to fix the configuration loss problem when resetting and
setting channel number.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the coalesce configuation lost problem when
setting the channel number by restoring all vectors's coalesce
configuation to vector 0's, because all vectors belonging to
the same netdev have the same coalesce configuation for now.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch refoctors the coalesce related struct by introducing
the hns3_enet_coalesce struct, in order to fix the coalesce
configuation lost problem when changing the channel number.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Coalesce configuration will be set to default value by
hns3_nic_init_vector_data during reset, which causes the
coalesce configuration loss problem.

This patch fixes it by setting the default value in
hns3_nic_alloc_vector_data, which will not be called in the
reset process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a get_vector function, which allocate the vectors
for a client, but there is not a put_vector to free the
vector.

This patch introduces the put_vector function in order to
fix the coalesce configuration lost problem during reset
process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In hns3_set_ringparam, hns3_uninit_all_ring frees the
memory pointed by priv->ring_data[i].ring, and
hns3_change_all_ring_bd_num use that pointer without mallocing,
which will cause a use-after-free problem.

The patch fixes it by not freeing the memory in
hns3_uninit_all_ring, and uses hns3_put_ring_config to free it
when necessary.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pause configuration will be set to default value by hclge_tm_schd_init
during reset, which causes the RSS configuration loss problem.

This patch fixes it by calling hclge_tm_init_hw during reset process
, which will set the pause configuration to default value.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RSS configuration will be set to default value by hclge_rss_init_hw
during reset, which causes the RSS configuration loss problem.

This patch fixes it by setting the default value in
hclge_rss_init_cfg function, which will not be called in the reset
process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch refactors the hclge_get/set_rss_tuple function
in order to fix the rss configuration loss problem during
reset process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch refactors the hclge_get/set_rss function in
order to fix the rss configuration loss problem during
reset process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>