- 21 Jan, 2019 17 commits
-
-
Yangtao Li authored
We already have the DEFINE_SHOW_ATTRIBUTE. There is no need to define bdisp_dbg_declare and hva_dbg_declare, so remove them. Also use DEFINE_SHOW_ATTRIBUTE to simplify some code. Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Yangtao Li authored
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code. Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Matt Ranostay authored
Add initial support for MLX90640 thermal cameras which output an 32x24 greyscale pixel image along with 2 rows of coefficent data. Because of this the data outputed is really 32x26 and needs the two rows removed after using the coefficent information to generate processed images in userspace. Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Matt Ranostay authored
Cc: devicetree@vger.kernel.org Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Pawe? Chmiel authored
Add device tree bindings for si470x family radio receiver driver. Signed-off-by: Pawe? Chmiel <pawel.mikolaj.chmiel@gmail.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Pawe? Chmiel authored
If reset-gpio is defined, use it to bring device out of reset. Without this, it's not possible to access si470x registers. Signed-off-by: Pawe? Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Pawe? Chmiel authored
Simplify cleanup of failures by using managed resource helpers Signed-off-by: Pawe? Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Pawe? Chmiel authored
This commit enables device tree support adding simple of_match table. Signed-off-by: Pawe? Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
French, Nicholas A authored
ivtvfb was previously disabled for x86 PAT-enabled systems by commit 1bf1735b ("x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled") as a workaround to abstract MTRR code away from device drivers. The driver is not easily upgradable to the PAT-aware ioremap_wc() API since the firmware hides the address ranges that should be marked write-combined from the driver. However, since a write-combined cache on the framebuffer is only a performance enhancement not a requirement for the framebuffer to function, completely disabling the driver in this configuration is not necessary. Add force_pat module parameter and a corresponding kernel configuration parameter to optionally force initialization on PAT-enabled x86 systems with a warning about the lack of write-combined caching, and document the reasons the driver cannot be easily updated to support wc caching on all systems. Signed-off-by: Nick French <naf@ou.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> [hverkuil-cisco@xs4all.nl: fix typo, split long pr_ lines up] Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Hans Verkuil authored
This is a test stub driver for soc_camera. Since soc_camera is being deprecated (and in fact, nobody is using it anymore) there's no sense in keeping this test driver. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Hans Verkuil authored
With the removal of sh_mobile_ceu_camera.c this code is no longer used and can be removed. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Hans Verkuil authored
This driver got converted to not depend on soc_camera in commit 32e5a70d ("media: platform: Add Renesas CEU driver"). There's no sense in keeping the old version there. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Hans Verkuil authored
This driver got converted to not depend on soc_camera in commit 7b20f325 ("media: i2c: tw9910: Remove soc_camera dependencies"). There's no sense in keeping the old version there. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Hans Verkuil authored
This include isn't use anymore, so drop it. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Hans Verkuil authored
This driver got converted to not depend on soc_camera in commit 762c2812 ("media: i2c: ov772x: Remove soc_camera dependencies"). There's no sense in keeping the old version there. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Hans Verkuil authored
This driver got converted to not depend on soc_camera in commit 6a26f141 ("media: i2c: mt9t112: Remove soc_camera dependencies"). There's no sense in keeping the old version there. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Jacopo Mondi authored
As the tw9910 subdevice is registered through the v4l2-async framework, use the v4l2-async provided function to register it. Fixes: 7b20f325 ("media: i2c: tw9910: Remove soc_camera dependencies") Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
- 17 Jan, 2019 1 commit
-
-
Mauro Carvalho Chehab authored
This driver got converted to not depend on soc_camera on commit 57b0ad9e ("media: soc_camera: ov9640: move ov9640 out of soc_camera"). There's no sense on keeping the old version there. Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
- 16 Jan, 2019 22 commits
-
-
Steve Longerbeam authored
Also add an example pipeline for unconverted capture with interweave on SabreAuto. Cleanup some language in various places in the process. Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Steve Longerbeam authored
Allow sequential->interlaced interweaving but with top/bottom lines swapped to the output buffer. This can be accomplished by adding one line length to IDMAC output channel address, with a negative line length for the interlace offset. This is to allow the seq-bt -> interlaced-bt transformation, where bottom lines are still dominant (older in time) but with top lines first in the interweaved output buffer. With this support, the CSI can now allow seq-bt at its source pads, e.g. the following transformations are allowed in CSI from sink to source: seq-tb -> seq-bt seq-bt -> seq-bt alternate -> seq-bt Suggested-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Steve Longerbeam authored
If caller passes un-initialized field type V4L2_FIELD_ANY to CSI sink pad, the reset CSI crop window would not be correct, because the crop window depends on a valid input field type. To fix move the reset of crop and compose windows to after the call to imx_media_fill_default_mbus_fields(). Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Steve Longerbeam authored
prepare_vdi_in_buffers() was setting up the dma pointers as if the VDIC is always programmed to receive the fields in bottom-top order, i.e. as if ipu_vdi_set_field_order() only programs BT order in the VDIC. But that's not true, ipu_vdi_set_field_order() is working correctly. So fix prepare_vdi_in_buffers() to give the VDIC the fields in whatever order they were received by the video source, and rely on the VDIC to sort out which is top and which is bottom. Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Steve Longerbeam authored
Skip writing U/V components to odd rows for YVU420 in addition to YUV420 and NV12. Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Steve Longerbeam authored
If IDMAC interweaving is enabled in a write channel, the channel must write the odd chroma rows for 4:2:0 formats. Skipping writing the odd chroma rows produces corrupted captured 4:2:0 images when interweave is enabled. Reported-by: Krzysztof Ha?asa <khalasa@piap.pl> Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Steve Longerbeam authored
If the incoming sink field type is alternate, the reset crop height and crop height bounds must be set to twice the incoming height, because in alternate field mode, upstream will report only the lines for a single field, and the CSI captures the whole frame. Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Steve Longerbeam authored
IDMAC interlaced scan, a.k.a. interweave, should be enabled in the IDMAC output channels only if the IDMAC output pad field type is 'seq-bt' or 'seq-tb', and field type at the capture interface is 'interlaced*'. V4L2_FIELD_HAS_BOTH() macro should not be used on the input to determine enabling interlaced/interweave scan. That macro includes the 'interlaced' field types, and in those cases the data is already interweaved with top/bottom field lines. The CSI will capture whole frames when the source specifies alternate field mode. So the CSI also enables interweave for alternate input field type and the field type at capture interface is interlaced. Fix the logic for setting field type in try_fmt in CSI entity. The behavior should be: - No restrictions on field type at sink pad. - At the output pads, allow sequential fields in TB order, if the sink pad field type is sequential or alternate. Otherwise passthrough the field type from sink to source pad. Move this logic to new function csi_try_field(). These changes result in the following allowed field transformations from CSI sink -> source pads (all other field types at sink are passed through to source): seq-tb -> seq-tb seq-bt -> seq-tb alternate -> seq-tb In a future patch, the CSI sink -> source will allow: seq-tb -> seq-bt seq-bt -> seq-bt alternate -> seq-bt This will require supporting interweave with top/bottom line swapping. Until then seq-bt is not allowed at the CSI source pad because there is no way to swap top/bottom lines when interweaving to INTERLACED_BT -- note that despite the name, INTERLACED_BT is top-bottom order in memory. The BT in this case refers to field dominance: the bottom lines are older in time than the top lines. The capture interface device allows selecting IDMAC interweave by choosing INTERLACED_TB if the CSI/PRPENCVF source pad is seq-tb and INTERLACED_BT if the source pad is seq-bt (for future support of seq-bt). Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Steve Longerbeam authored
To support interlaced scan with planar formats, cpmem SLUV must be programmed with the correct chroma line stride. For full and partial planar 4:2:2 (YUV422P, NV16), chroma line stride must be doubled. For full and partial planar 4:2:0 (YUV420, YVU420, NV12), chroma line stride must _not_ be doubled, since a single chroma line is shared by two luma lines. Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Steve Longerbeam authored
The function ipu_csi_init_interface() was inverting the F-bit for NTSC case, in the CCIR_CODE_1/2 registers. The result being that for NTSC bottom-top field order, the CSI would swap fields and capture in top-bottom order. Instead, base field swap on the field order of the input to the CSI, and the field order of the requested output. If the input/output fields are sequential but different, swap fields, otherwise do not swap. This requires passing both the input and output mbus frame formats to ipu_csi_init_interface(). Move this code to a new private function ipu_csi_set_bt_interlaced_codes() that programs the CCIR_CODE_1/2 registers for interlaced BT.656 (and possibly interlaced BT.1120 in the future). When detecting input video standard from the input frame width/height, make sure to double height if input field type is alternate, since in that case input height only includes lines for one field. Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Steve Longerbeam authored
Adds two helper macros: V4L2_FIELD_IS_SEQUENTIAL: returns true if the given field type is 'sequential', that is a full frame is transmitted, or exists in memory, as all top field lines followed by all bottom field lines, or vice-versa. V4L2_FIELD_IS_INTERLACED: returns true if the given field type is 'interlaced', that is a full frame is transmitted, or exists in memory, as top field lines interlaced with bottom field lines. Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Steve Longerbeam authored
There is a block of code in rvin_group_link_notify() that prevents enabling a link to a VIN node if any entity in the media graph is in use. This prevents enabling a VIN link even if there is an in-use entity somewhere in the graph that is independent of the link's pipeline. For example, the code block will prevent enabling a link from the first rcar-csi2 receiver to a VIN node even if there is an enabled link somewhere far upstream on the second independent rcar-csi2 receiver pipeline. If this code block is meant to prevent modifying a link if any entity in the graph is actively involved in streaming (because modifying the CHSEL register fields can disrupt any/all running streams), then the entities stream counts should be checked rather than the use counts. (There is already such a check in __media_entity_setup_link() that verifies the stream_count of the link's source and sink entities are both zero, but that is insufficient, since there should be no running streams in the entire graph). Modify the code block to check the entity stream_count instead of the use_count (and elaborate on the comment). VIN node links can now be enabled even if there are other independent in-use entities that are not streaming. Fixes: c0cc5aef ("media: rcar-vin: add link notify for Gen3") Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Philipp Zabel authored
Allow to set a fixed quantization parameter offset between luma and chroma in the h.264 encoder. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Philipp Zabel authored
Allow to enable constrained intra prediction in the h.264 encoder. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Philipp Zabel authored
Allow to add fixed quantization parameter offset between luma and chroma quantization parameters. This control directly corresponds to the chroma_qp_index_offset field of the h.264 picture parameter set. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Philipp Zabel authored
Allow to enable h.264 constrained intra prediction (macroblocks using intra prediction modes are not allowed to use residual data and decoded samples of neighboring macroblocks coded using inter prediction modes). This control directly corresponds to the constrained_intra_pred_flag field in the h.264 picture parameter set. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Philipp Zabel authored
The COM3 register at address 0x0c already defaults to 0x10, the two bits COM3[7:6] are set according to V4L2 controls by sethvflip later. There is no need to set it multiple times during bridge initialization. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Philipp Zabel authored
This register is later overwritten by set_frame_rate anyway. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Philipp Zabel authored
The video format, payload size, and frame size setup is video format and frame size specific. Those registers are overwritten during bridge_start anyway. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Philipp Zabel authored
Add support to pass through the sensor's native SGBRG8 bayer pattern, allowing to cut the required USB bandwidth in half. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Philipp Zabel authored
In preparation for adding SGBRG8 as a second video format besides YUYV, move video format specific register settings from the bridge_init array into the bridge_start arrays. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Philipp Zabel authored
If a driver supports multiple pixel formats with the same frame size, TRY_FMT will currently always return the first pixel format. Fix this by adding pixelformat support to wxh_to_nearest_mode(). Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-