Skip to content

L
linux
Switch branch/tag
  1. 27 Jun, 2008 7 commits
    • Neil Brown's avatar
      Allow setting start point for requested check/repair · 5e96ee65
      Neil Brown authored 
      This makes it possible to just resync a small part of an array.
e.g. if a drive reports that it has questionable sectors,
a 'repair' of just the region covering those sectors will
cause them to be read and, if there is an error, re-written
with correct data.
Signed-off-by: default avatarNeil Brown <neilb@suse.de>
      5e96ee65
    • Neil Brown's avatar
      Improve setting of "events_cleared" for write-intent bitmaps. · a0da84f3
      Neil Brown authored 
      When an array is degraded, bits in the write-intent bitmap are not
cleared, so that if the missing device is re-added, it can be synced
by only updated those parts of the device that have changed since
it was removed.

The enable this a 'events_cleared' value is stored. It is the event
counter for the array the last time that any bits were cleared.

Sometimes - if a device disappears from an array while it is 'clean' -
the events_cleared value gets updated incorrectly (there are subtle
ordering issues between updateing events in the main metadata and the
bitmap metadata) resulting in the missing device appearing to require
a full resync when it is re-added.

With this patch, we update events_cleared precisely when we are about
to clear a bit in the bitmap.  We record events_cleared when we clear
the bit internally, and copy that to the superblock which is written
out before the bit on storage.  This makes it more "obviously correct".

We also need to update events_cleared when the event_count is going
backwards (as happens on a dirty->clean transition of a non-degraded
array).

Thanks to Mike Snitzer for identifying this problem and testing early
"fixes".

Cc:  "Mike Snitzer" <snitzer@gmail.com>
Signed-off-by: default avatarNeil Brown <neilb@suse.de>
      a0da84f3
    • Neil Brown's avatar
      use bio_endio instead of a call to bi_end_io · 0e13fe23
      Neil Brown authored 
      Turn calls to bi->bi_end_io() into bio_endio(). Apparently bio_endio does
exactly the same error processing as is hardcoded at these places.

bio_endio() avoids recursion (or will soon), so it should be used.
Signed-off-by: default avatarMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: default avatarNeil Brown <neilb@suse.de>
      0e13fe23
    • Nikanth Karthikesan's avatar
      linear: correct disk numbering error check · 13864515
      Nikanth Karthikesan authored 
      From: "Nikanth Karthikesan" <knikanth@novell.com>

Correct disk numbering problem check.
Signed-off-by: default avatarNikanth Karthikesan <knikanth@suse.de>
Signed-off-by: default avatarNeil Brown <neilb@suse.de>
      13864515
    • Neil Brown's avatar
      Fix error paths if md_probe fails. · 9bbbca3a
      Neil Brown authored 
      md_probe can fail (e.g. alloc_disk could fail) without
returning an error (as it alway returns NULL).
So when we call mddev_find immediately afterwards, we need
to check that md_probe actually succeeded.  This means checking
that mdev->gendisk is non-NULL.

cc: <stable@kernel.org>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: default avatarNeil Brown <neilb@suse.de>
      9bbbca3a
    • Neil Brown's avatar
      Don't acknowlege that stripe-expand is complete until it really is. · efe31143
      Neil Brown authored 
      We shouldn't acknowledge that a stripe has been expanded (When
reshaping a raid5 by adding a device) until the moved data has
actually been written out.  However we are currently
acknowledging (by calling md_done_sync) when the POST_XOR
is complete and before the write.

So track in s.locked whether there are pending writes, and don't
call md_done_sync yet if there are.

Note: we all set R5_LOCKED on devices which are are about to
read from.  This probably isn't technically necessary, but is
usually done when writing a block, and justifies the use of
s.locked here.

This bug can lead to a crash if an array is stopped while an reshape
is in progress.

Cc: <stable@kernel.org>
Signed-off-by: default avatarNeil Brown <neilb@suse.de>
      efe31143
    • Neil Brown's avatar
      Ensure interrupted recovery completed properly (v1 metadata plus bitmap) · 8c2e870a
      Neil Brown authored 
      If, while assembling an array, we find a device which is not fully
in-sync with the array, it is important to set the "fullsync" flags.
This is an exact analog to the setting of this flag in hot_add_disk
methods.

Currently, only v1.x metadata supports having devices in an array
which are not fully in-sync (it keep track of how in sync they are).
The 'fullsync' flag only makes a difference when a write-intent bitmap
is being used.  In this case it tells recovery to ignore the bitmap
and recovery all blocks.

This fix is already in place for raid1, but not raid5/6 or raid10.

So without this fix, a raid1 ir raid4/5/6 array with version 1.x
metadata and a write intent bitmaps, that is stopped in the middle
of a recovery, will appear to complete the recovery instantly
after it is reassembled, but the recovery will not be correct.

If you might have an array like that, issueing
   echo repair > /sys/block/mdXX/md/sync_action

will make sure recovery completes properly.

Cc: <stable@kernel.org>
Signed-off-by: default avatarNeil Brown <neilb@suse.de>
      8c2e870a
  3. 25 Jun, 2008 4 commits
  5. 24 Jun, 2008 26 commits
  7. 23 Jun, 2008 3 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7