so will disable that feature by default, and only enable that via
pci=check_enable_amd_mmconf or for system match with dmi table.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

normally BIOSes assign io/mmio range to different HT links without
overlapping, even same node same link should get non overlapping
entries.

but Rafael L. Wysocki's buggy BIOS creates a link with overlapping
entries for mmio and io:

  node 0 link 0: io port [1000, ffffff]
  node 0 link 0: mmio [e0000000, efffffff]
  node 0 link 0: mmio [a0000, bffff]
  node 0 link 0: mmio [80000000, ffffffff]

try to merge them and we will get:

  bus: [00, ff] on node 0 link 0
  bus: 00 index 0 io port: [0, ffff]
  bus: 00 index 1 mmio: [80000000, fcffffffff]
  bus: 00 index 2 mmio: [a0000, bffff]

so later we will reduce the chance to assign used resource to
unassigned device.
Reported-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Tested-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

[mingo@elte.hu: split from "x86_64: get boot_cpu_id as early for k8_scan_nodes]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

if there's only one root bus there's no need to split resources.

This patch fixes the issue described at:

  http://lkml.org/lkml/2008/4/10/304Reported-and-bisected-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

some bioses give same range to mmconf for fam10h msr, and mmio for node/link.

fam10h msr will overide mmio for node/link.
so we can not assign range to devices under node/link for unassigned resources.

this patch will take range out from the mmio for node/link
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

scan AMD opteron io/mmio routing to make sure every pci root bus get correct
resource range. Thus later pci scan could assign correct resource to device
with unassigned resource.

this can fix a system without _CRS for multi pci root bus.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

... so we use the same code with Quad core cpu as old opteron.

This patch is useful when acpi=off or _PXM is not there in DSDT.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Currently, on an amd k8 system with multi ht chains, the numa_node of
pci devices under /sys/devices/pci0000:80/* is always 0, even if that
chain is on node 1 or 2 or 3.

Workaround: pcibus_to_node(bus) is used when we want to get the node that
pci_device is on.

In struct device, we already have numa_node member, and we could use
dev_to_node()/set_dev_node() to get and set numa_node in the device.
set_dev_node is called in pci_device_add() with pcibus_to_node(bus),
and pcibus_to_node uses bus->sysdata for nodeid.

The problem is when pci_add_device is called, bus->sysdata is not assigned
correct nodeid yet. The result is that numa_node will always be 0.

pcibios_scan_root and pci_scan_root could take sysdata. So we need to get
mp_bus_to_node mapping before these two are called, and thus
get_mp_bus_to_node could get correct node for sysdata in root bus.

In scanning of the root bus, all child busses will take parent bus sysdata.
So all pci_device->dev.numa_node will be assigned correctly and automatically.

Later we could use dev_to_node(&pci_dev->dev) to get numa_node, and we
could also could make other bus specific device get the correct numa_node
too.

This is an updated version of pci_sysdata and Jeff's pci_domain patch.

[ mingo@elte.hu: build fix ]
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

doesn't need to check if it is type1 or type2, we can use raw_pci_ops
directly.

also make pci_direct_conf1 static again.

anyway is there system with type 2 and mmconf support?
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

mmconfig is only used to access extended configuration space.

so don't need to reject MFG that only have one entry and only handle bus0.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

in the device_add, we try to use use parent numa_node.
need to make sure pci root bus's bridge device numa_node is set.
then we could use device->numa_node direclty for all device.
and don't need to call pcibus_to_node().
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Separate mmconf for fam10h out from setup_64.c
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

some BIOS only let AMD fam 10h handle bus0, and nvidia mcp55/ck804
to handle other buses. at that case MCFG will cover all over them.

but with acpi=off, we can not use MCFG. this patch will double check
the busnbits, and if it is less handling 256 bues, and acpi=off
will forcely reset the mmconf in msr, so we still use mmconf in above case.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

so even booting kernel with acpi=off or even MCFG is not there, we still can
use MMCONFIG.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Greg KH <greg@kroah.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

So we can use MMCONF when MMCONF is not set by BIOS

using TOP_MEM2 msr to get memory top, and try to scan fam10h mmio routing to
make sure the range is not conflicted with some prefetch MMIO that is above 4G.
(current only LinuxBIOS assign 64 bit mmio above 4G for some co-processor)
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

reuse pci_cfg_space_size but skip check pci express and pci-x CAP ID.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Patch
	"x86: validate against ACPI motherboard resources"

changed the mmconf init sequence, and init MMCONF late in acpi_init.

here change it back to old sequence:

 1. check hostbridge in early
 2. check MCFG with e820 in early
 3. if all fail, will check MCFg with acpi _CRS in acpi_init

So we can make MCONF working again when acpi=off is set if hostbridge
support that.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

For x86_64, need to free pci_mmcfg_virt, and iounmap some pointers
when MMCONF is not reserved in E820 or acpi _CRS and get rejected.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

This path adds validation of the MMCONFIG table against the ACPI reserved
motherboard resources.  If the MMCONFIG table is found to be reserved in
ACPI, we don't bother checking the E820 table.  The PCI Express firmware
spec apparently tells BIOS developers that reservation in ACPI is required
and E820 reservation is optional, so checking against ACPI first makes
sense.  Many BIOSes don't reserve the MMCONFIG region in E820 even though
it is perfectly functional, the existing check needlessly disables MMCONFIG
in these cases.

In order to do this, MMCONFIG setup has been split into two phases.  If PCI
configuration type 1 is not available then MMCONFIG is enabled early as
before.  Otherwise, it is enabled later after the ACPI interpreter is
enabled, since we need to be able to execute control methods in order to
check the ACPI reserved resources.  Presently this is just triggered off
the end of ACPI interpreter initialization.

There are a few other behavioral changes here:

- Validate all MMCONFIG configurations provided, not just the first one.

- Validate the entire required length of each configuration according to
  the provided ending bus number is reserved, not just the minimum required
  allocation.

- Validate that the area is reserved even if we read it from the chipset
  directly and not from the MCFG table.  This catches the case where the
  BIOS didn't set the location properly in the chipset and has mapped it
  over other things it shouldn't have.

This also cleans up the MMCONFIG initialization functions so that they
simply do nothing if MMCONFIG is not compiled in.

Based on an original patch by Rajesh Shah from Intel.

[akpm@linux-foundation.org: many fixes and cleanups]
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andi Kleen <ak@suse.de>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-bootmem-v3

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-bootmem-v3:
  x86_64/mm: check and print vmemmap allocation continuous
  x86_64: fix setup_node_bootmem to support big mem excluding with memmap
  x86_64: make reserve_bootmem_generic() use new reserve_bootmem()
  mm: allow reserve_bootmem() cross nodes
  mm: offset align in alloc_bootmem()
  mm: fix alloc_bootmem_core to use fast searching for all nodes
  mm: make mem_map allocation continuous

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
  kbuild: scripts/Makefile.modpost typo fix
  kbuild: soften MODULE_LICENSE check

On big systems with lots of memory, don't print out too much during
bootup, and make it easy to find if it is continuous.

on 256G 8 sockets system will get
 [ffffe20000000000-ffffe20002bfffff] PMD -> [ffff810001400000-ffff810003ffffff] on node 0
[ffffe2001c700000-ffffe2001c7fffff] potential offnode page_structs
 [ffffe20002c00000-ffffe2001c7fffff] PMD -> [ffff81000c000000-ffff8100255fffff] on node 0
[ffffe20038700000-ffffe200387fffff] potential offnode page_structs
 [ffffe2001c800000-ffffe200387fffff] PMD -> [ffff810820200000-ffff81083c1fffff] on node 1
 [ffffe20040000000-ffffe2007fffffff] PUD ->ffff811027a00000 on node 2
 [ffffe20038800000-ffffe2003fffffff] PMD -> [ffff811020200000-ffff8110279fffff] on node 2
[ffffe20054700000-ffffe200547fffff] potential offnode page_structs
 [ffffe20040000000-ffffe200547fffff] PMD -> [ffff811027c00000-ffff81103c3fffff] on node 2
[ffffe20070700000-ffffe200707fffff] potential offnode page_structs
 [ffffe20054800000-ffffe200707fffff] PMD -> [ffff811820200000-ffff81183c1fffff] on node 3
 [ffffe20080000000-ffffe200bfffffff] PUD ->ffff81202fa00000 on node 4
 [ffffe20070800000-ffffe2007fffffff] PMD -> [ffff812020200000-ffff81202f9fffff] on node 4
[ffffe2008c700000-ffffe2008c7fffff] potential offnode page_structs
 [ffffe20080000000-ffffe2008c7fffff] PMD -> [ffff81202fc00000-ffff81203c3fffff] on node 4
[ffffe200a8700000-ffffe200a87fffff] potential offnode page_structs
 [ffffe2008c800000-ffffe200a87fffff] PMD -> [ffff812820200000-ffff81283c1fffff] on node 5
 [ffffe200c0000000-ffffe200ffffffff] PUD ->ffff813037a00000 on node 6
 [ffffe200a8800000-ffffe200bfffffff] PMD -> [ffff813020200000-ffff8130379fffff] on node 6
[ffffe200c4700000-ffffe200c47fffff] potential offnode page_structs
 [ffffe200c0000000-ffffe200c47fffff] PMD -> [ffff813037c00000-ffff81303c3fffff] on node 6
 [ffffe200c4800000-ffffe200e07fffff] PMD -> [ffff813820200000-ffff81383c1fffff] on node 7

instead of a very long print out...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

typical case: four sockets system, every node has 4g ram, and we are using:

	memmap=10g$4g

to mask out memory on node1 and node2

when numa is enabled, early_node_mem is used to get node_data and node_bootmap.

if it can not get memory from the same node with find_e820_area(), it will
use alloc_bootmem to get buff from previous nodes.

so check it and print out some info about it.

need to move early_res_to_bootmem into every setup_node_bootmem.
and it takes range that node has. otherwise alloc_bootmem could return addr
that reserved early.

depends on "mm: make reserve_bootmem can crossed the nodes".
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

"mm: make reserve_bootmem can crossed the nodes" provides new
reserve_bootmem(), let reserve_bootmem_generic() use that.

reserve_bootmem_generic() is used to reserve initramdisk, so this way
we can make sure even when bootloader or kexec load ranges cross the
node memory boundaries, reserve_bootmem still works.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

split reserve_bootmem_core() into two functions, one which checks
conflicts, and one which sets the bits.

and make reserve_bootmem to loop bdata_list to cross the nodes.

user could be crashkernel and ramdisk..., in case the range provided
by those externalities crosses the nodes.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

need offset alignment when node_boot_start's alignment is less than
the alignment required.

use local node_boot_start to match alignment - so don't add extra operation
in search loop.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Make the nodes other than node 0 use bdata->last_success for fast
search too.

We need to use __alloc_bootmem_core() for vmemmap allocation for other
nodes when numa and sparsemem/vmemmap are enabled.

Also, make fail_block path increase i with incr only after ALIGN
to avoid extra increase when size is larger than align.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

vmemmap allocation currently has this layout:

 [ffffe20000000000-ffffe200001fffff] PMD ->ffff810001400000 on node 0
 [ffffe20000200000-ffffe200003fffff] PMD ->ffff810001800000 on node 0
 [ffffe20000400000-ffffe200005fffff] PMD ->ffff810001c00000 on node 0
 [ffffe20000600000-ffffe200007fffff] PMD ->ffff810002000000 on node 0
 [ffffe20000800000-ffffe200009fffff] PMD ->ffff810002400000 on node 0
...

note that there is a 2M hole between them - not optimal.

the root cause is that usemap (24 bytes) will be allocated after every 2M
mem_map, and it will push next vmemmap (2M) to the next (2M) alignment.

solution: try to allocate the mem_map continously.

after the patch, we get:

 [ffffe20000000000-ffffe200001fffff] PMD ->ffff810001400000 on node 0
 [ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0
 [ffffe20000400000-ffffe200005fffff] PMD ->ffff810001800000 on node 0
 [ffffe20000600000-ffffe200007fffff] PMD ->ffff810001a00000 on node 0
 [ffffe20000800000-ffffe200009fffff] PMD ->ffff810001c00000 on node 0
...

which is the ideal layout.

and usemap will share a page because of they are allocated continuously too:

sparse_early_usemap_alloc: usemap = ffff810024e00000 size = 24
sparse_early_usemap_alloc: usemap = ffff810024e00080 size = 24
sparse_early_usemap_alloc: usemap = ffff810024e00100 size = 24
sparse_early_usemap_alloc: usemap = ffff810024e00180 size = 24
...

so we make the bootmem allocation more compact and use less memory
for usemap => mission accomplished ;-)
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-generic-bitops-v3

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-generic-bitops-v3:
  x86, bitops: select the generic bitmap search functions
  x86: include/asm-x86/pgalloc.h/bitops.h: checkpatch cleanups - formatting only
  x86: finalize bitops unification
  x86, UML: remove x86-specific implementations of find_first_bit
  x86: optimize find_first_bit for small bitmaps
  x86: switch 64-bit to generic find_first_bit
  x86: generic versions of find_first_(zero_)bit, convert i386
  bitops: use __fls for fls64 on 64-bit archs
  generic: implement __fls on all 64-bit archs
  generic: introduce a generic __fls implementation
  x86: merge the simple bitops and move them to bitops.h
  x86, generic: optimize find_next_(zero_)bit for small constant-size bitmaps
  x86, uml: fix uml with generic find_next_bit for x86
  x86: change x86 to use generic find_next_bit
  uml: Kconfig cleanup
  uml: fix build error

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (46 commits)
  ide: constify struct ide_dma_ops
  ide: add struct ide_dma_ops (take 3)
  ide: add IDE_HFLAG_SERIALIZE_DMA host flag
  sl82c105: check bridge revision in sl82c105_init_one()
  au1xxx-ide: use ->init_dma method
  palm_bk3710: use ->init_dma method
  sgiioc4: use ->init_dma method
  icside: use ->init_dma method
  ide-pmac: use ->init_dma method
  ide: do complete DMA setup in ->init_dma method (take 2)
  au1xxx-ide: fix MWDMA support
  ide: cleanup ide_setup_dma()
  ide: factor out setting PCI bus-mastering from ide_hwif_setup_dma()
  ide: export ide_allocate_dma_engine()
  ide: move ide_setup_dma() call out from ->init_dma method
  alim15x3: skip DMA initialization completely on revs < 0x20
  pdc202xx_old: remove init_dma_pdc202xx()
  ide: don't display "BIOS" settings in ide_setup_dma()
  ide: remove ->cds field from ide_hwif_t (take 2)
  ide: remove ide_dma_iobase()
  ...

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-bootparam

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-bootparam:
  x86, boot: Document for linked list of struct setup_data
  x86, boot: export linked list of struct setup_data via debugfs
  x86, boot: add linked list of struct setup_data
  x86, boot: add free_early to early reservation machanism

* Export ide_dma_exec_cmd() and __ide_dma_test_irq().

* Constify struct ide_dma_ops.

* Always set hwif->dma_ops to &sff_dma_ops in ide_setup_dma()
  (it is later overriden by ide_init_port() if needed) and drop
  'const struct ide_port_info *d' argument.

While at it:

* Rename __ide_dma_test_irq() to ide_dma_test_irq().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add struct ide_dma_ops and convert core code + drivers to use it.

While at it:

* Drop "ide_" prefix from ->ide_dma_end and ->ide_dma_test_irq methods.

* Drop "ide_" "infixes" from DMA methods.

* au1xxx-ide.c:
  - use auide_dma_{test_irq,end}() directly in auide_dma_timeout()

* pdc202xx_old.c:
  - drop "old_" "infixes" from DMA methods

* siimage.c:
  - add siimage_dma_test_irq() helper
  - print SATA warning in siimage_init_one()

* Remove no longer needed ->init_hwif implementations.

v2:
* Changes based on review from Sergei:
  - s/siimage_ide_dma_test_irq/siimage_dma_test_irq/
  - s/drive->hwif/hwif/ in idefloppy_pc_intr().
  - fix patch description w.r.t. au1xxx-ide changes
  - fix au1xxx-ide build
  - fix naming for cmd64*_dma_ops
  - drop "ide_" and "old_" infixes
  - s/hpt3xxx_dma_ops/hpt37x_dma_ops/
  - s/hpt370x_dma_ops/hpt370_dma_ops/
  - use correct DMA ops for HPT302/N, HPT371/N and HPT374
  - s/it821x_smart_dma_ops/it821x_pass_through_dma_ops/

v3:
* Two bugs slipped in v2 (noticed by Sergei):
  - use correct DMA ops for HPT374 (for real this time)
  - handle HPT370/HPT370A properly
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_SERIALIZE_DMA host flag to serialize ports
  if DMA is available and handle it in ide_init_port().

* Convert sl82c105 host driver to use this new flag.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Make sl82c105_bridge_revision() return 'u8' instead of 'unsigned long'.

* Check bridge revision in sl82c105_init_one().

While at:

* Use proper KERN_ level for printk().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Pass 'ide_hwif_t *hwif' instead of '_auide_hwif *auide' to
  auide_ddma_init().

* Add 'const struct ide_port_info *d' argument to auide_ddma_init().

* Convert the driver to use ->init_dma method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move DMA setup to palm_bk3710_init_dma().

* Convert the driver to use ->init_dma method.

Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move dma_base check from sgiioc4_ide_setup_pci_device()
  to ide_dma_sgiioc4().

* Replace ide_dma_sgiioc4() 'unsigned long dma_base' argument
  by 'const struct ide_port_info *d'.

* Move hwif->INB setup from ide_init_sgiioc4() to
  sgiioc4_ide_setup_pci_device().

* Move ide_init_sgiioc4() call from sgiioc4_ide_setup_pci_device()
  to ide_dma_sgiioc4().

* Convert the driver to use ->init_dma method.

Cc: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add 'const struct ide_port_info *d' argument to icside_dma_init().

* Make icside_dma_init() return an error value and add icside_dma_off_init()
  (->init_dma implementation for case when DMA cannot be enabled).

* Convert the driver to use ->init_dma method.

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move pmif->dma_regs check from pmac_ide_setup_device() to
  pmac_ide_init_dma().

* Get 'pmif' from 'hwif->hwif_data' in pmac_ide_init_dma() and replace
  'pmac_ide_hwif_t *pmif' argument by 'const struct ide_port_info *d'.

* Add pmac_ide_init_dma() implementation for CONFIG_BLK_DEV_IDEDMA_PMAC=n
  case and convert the driver to use ->init_dma method.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>