- 02 Aug, 2016 39 commits
-
-
Easwar Hariharan authored
Some QSFP cables assert the interrupt line as a side effect of module plug-in and power up. This causes the SerDes and QSFP tuning algorithm to begin cable initialization by reading the QSFP memory map over I2C, which fails. This patch ignores any interrupt line assertion until the module has completed power up and voltage rails have stabilized, which can take a maximum of 500 ms per the SFF-8679 specification. Reviewed-by:
Dean Luick <dean.luick@intel.com> Signed-off-by:
Easwar Hariharan <easwar.hariharan@intel.com> Signed-off-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by:
Doug Ledford <dledford@redhat.com>
-
Easwar Hariharan authored
QSFP CDR enablement is now controlled by determining power class and the configuration file. We disable the DC 8051 from requesting enablement or disabling of TX and RX CDRs by removing the code that allowed the DC 8051 to request changes. Reviewed-by:
-
Jianxin Xiong authored
Hanging has been observed while writing a file over NFSoRDMA. Dmesg on the server contains messages like these: [ 931.992501] svcrdma: Error -22 posting RDMA_READ [ 952.076879] svcrdma: Error -22 posting RDMA_READ [ 982.154127] svcrdma: Error -22 posting RDMA_READ [ 1012.235884] svcrdma: Error -22 posting RDMA_READ [ 1042.319194] svcrdma: Error -22 posting RDMA_READ Here is why: With the base memory management extension enabled, FRMR is used instead of FMR. The xprtrdma server issues each RDMA read request as the following bundle: (1)IB_WR_REG_MR, signaled; (2)IB_WR_RDMA_READ, signaled; (3)IB_WR_LOCAL_INV, signaled & fencing. These requests are signaled. In order to generate completion, the fast register work request is processed by the hfi1 send engine after being posted to the work queue, and the corresponding lkey is not valid until the request is processed. However, the rdmavt driver validates lkey when the RDMA read request is posted and thus it fails immediately with error -EINVAL (-22). This patch changes the work flow of local operations (fast register and local invalidate) so that fast register work requests are always processed immediately to ensure that the corresponding lkey is valid when subsequent work requests are posted. Local invalidate requests are processed immediately if fencing is not required and no previous local invalidate request is pending. To allow completion generation for signaled local operations that have been processed before posting to the work queue, an internal send flag RVT_SEND_COMPLETION_ONLY is added. The hfi1 send engine checks this flag and only generates completion for such requests. Reviewed-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Jianxin Xiong <jianxin.xiong@intel.com> Signed-off-by:
-
Mike Marciniszyn authored
This fix allows for support of in-kernel reserved operations without impacting the ULP user. The low level driver can register a non-zero value which will be transparently added to the send queue size and hidden from the ULP in every respect. ULP post sends will never see a full queue due to a reserved post send and reserved operations will never exceed that registered value. The s_avail will continue to track the ULP swqe availability and the difference between the reserved value and the reserved in use will track reserved availabity. Reviewed-by:
Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by:
-
Grzegorz Heldt authored
Trace shows incorrect amount of allocated memory. Fix trace to display memory in KB. Reviewed-by:
Grzegorz Heldt <grzegorz.heldt@intel.com> Signed-off-by:
-
Tadeusz Struk authored
Add sysfs entry to allow user to override affinity for SDMA engine interrupts. Reviewed-by:
Tadeusz Struk <tadeusz.struk@intel.com> Signed-off-by:
-
Dean Luick authored
Enhance the PCIe Gen3 recipe to support static CTLE tuning, and add a switch to choose between static and dynamic approaches. Make discrete chips default to static CTLE tuning. Reviewed-by:
-
Jianxin Xiong authored
This fixes the following warnings with PROVE_LOCKING and PROVE_RCU enabled in the kernel: case (1): [ INFO: suspicious RCU usage. ] drivers/infiniband/hw/hfi1/init.c:532 suspicious rcu_dereference_check() usage! case (2): [ INFO: suspicious RCU usage. ] drivers/infiniband/hw/hfi1/hfi.h:1624 suspicious rcu_dereference_check() usage! Reviewed-by:
-
Jianxin Xiong authored
This fixes the following warning with PROV_LOCKING enabled kernel: INFO: trying to register non-static key. the code is fine but needs lockdep annotation. turning off the locking correctness validator. CPU: 15 PID: 12286 Comm: modprobe Not tainted 4.7.0-rc5.prove_rcu+ #1 Hardware name: Intel Corporation S2600WT2R/S2600WT2R, ...... Call Trace: [<ffffffff8139ec0d>] dump_stack+0x85/0xc8 [<ffffffff810eb765>] register_lock_class+0x415/0x4b0 [<ffffffff810ede1c>] ? __lock_acquire+0x40c/0x1960 [<ffffffff810edaa9>] __lock_acquire+0x99/0x1960 [<ffffffff8120ab62>] ? find_vmap_area+0x42/0x60 [<ffffffff8120ab39>] ? find_vmap_area+0x19/0x60 [<ffffffff810ef9d3>] lock_acquire+0xd3/0x200 [<ffffffffa049d598>] ? rvt_create_cq+0xc8/0x250 [rdmavt] [<ffffffff81763391>] _raw_spin_lock+0x31/0x40 [<ffffffffa049d598>] ? rvt_create_cq+0xc8/0x250 [rdmavt] [<ffffffffa049d598>] rvt_create_cq+0xc8/0x250 [rdmavt] [<ffffffff810ead46>] ? static_obj+0x36/0x50 [<ffffffffa0469e39>] ib_alloc_cq+0x49/0x180 [ib_core] [<ffffffffa047bed4>] ib_mad_init_device+0x204/0x6d0 [ib_core] [<ffffffff810e968f>] ? up_write+0x1f/0x40 [<ffffffffa046e2c0>] ib_register_device+0x3d0/0x510 [ib_core] [<ffffffffa0752410>] ? read_cc_setting_bin+0x200/0x200 [hfi1] [<ffffffff810ead46>] ? static_obj+0x36/0x50 [<ffffffff810eb888>] ? lockdep_init_map+0x88/0x200 [<ffffffffa049cbff>] rvt_register_device+0x17f/0x320 [rdmavt] [<ffffffffa0766caa>] hfi1_register_ib_device+0x6ca/0x7c0 [hfi1] [<ffffffffa0733de4>] init_one+0x2b4/0x430 [hfi1] [<ffffffff813e40a5>] local_pci_probe+0x45/0xa0 [<ffffffff813e5110>] ? pci_match_device+0xe0/0x110 [<ffffffff813e550c>] pci_device_probe+0xfc/0x140 [<ffffffff814daee9>] driver_probe_device+0x239/0x460 [<ffffffff814db1dd>] __driver_attach+0xcd/0xf0 [<ffffffff814db110>] ? driver_probe_device+0x460/0x460 [<ffffffff814d89b3>] bus_for_each_dev+0x73/0xc0 [<ffffffff814da74e>] driver_attach+0x1e/0x20 [<ffffffff814da1b3>] bus_add_driver+0x1d3/0x290 [<ffffffffa04cc114>] ? dev_init+0x114/0x114 [hfi1] [<ffffffff814dbf60>] driver_register+0x60/0xe0 [<ffffffffa04cc114>] ? dev_init+0x114/0x114 [hfi1] [<ffffffff813e39d0>] __pci_register_driver+0x60/0x70 [<ffffffffa04cc2aa>] hfi1_mod_init+0x196/0x1fe [hfi1] [<ffffffff81002190>] do_one_initcall+0x50/0x190 [<ffffffff8110be72>] ? rcu_read_lock_sched_held+0x62/0x70 [<ffffffff8122d4aa>] ? kmem_cache_alloc_trace+0x23a/0x2a0 [<ffffffff811c1881>] ? do_init_module+0x27/0x1dc [<ffffffff811c18ba>] do_init_module+0x60/0x1dc [<ffffffff811360cc>] load_module+0x132c/0x1ac0 [<ffffffff81132c40>] ? __symbol_put+0x60/0x60 [<ffffffff8133e50d>] ? ima_post_read_file+0x3d/0x80 Cc: Stable <stable@vger.kernel.org> # 4.6+ Reviewed-by:
-
Dean Luick authored
Read the version of the SBus, PCIe SerDes, and Fabric Serdes firmwares at driver load time. Reviewed-by:
-
Dean Luick authored
When link up fails in LNI, the local and peer state complete frames are reported as numbers. Explain what the values mean so the operator can better diagnose the problem. Reviewed-by:
-
Harish Chegondi authored
Currently, the default number of kernel receive contexts is set to the number of NUMA nodes on the system plus one for control context. However, the systems that have a single socket and/or have NUMA disabled in the BIOS will have only one receive context by default. This patch would ensure that by default there will be at least two kernel receive contexts plus one for control context regardless of the number of NUMA nodes on the system. The user can override the default number of kernel receive contexts with the krcvqs module parameter. Reviewed-by:
Harish Chegondi <harish.chegondi@intel.com> Signed-off-by:
-
Jianxin Xiong authored
Advertise and add the capability of handing all aspects of IBTA extended memory management support in post send. Reviewed-by:
-
Jianxin Xiong authored
In order to support extended memory management support, add send side processing of work requests of type IB_WR_REG_MR, IB_WR_LOCAL_INV, and IB_WR_SEND_WITH_INV. The first two are local operations and are supported for both RC and UC. Send with invalidate is only supported for RC because the corresponding IB opcodes are not defined for UC. Reviewed-by:
-
Jianxin Xiong authored
As part of enabling extended memory management support, add the processing of the RC send with invalidate. Reviewed-by:
-
Jianxin Xiong authored
Some work requests are local operations, such as IB_WR_REG_MR and IB_WR_LOCAL_INV. They differ from non-local operations in that: (1) Local operations can be processed immediately without being posted to the send queue if neither fencing nor completion generation is needed. However, to ensure correct ordering, once a local operation is posted to the work queue due to fencing or completion requiement, all subsequent local operations must also be posted to the work queue until all the local operations on the work queue have completed. (2) Local operations don't send packets over the wire and thus don't need (and shouldn't update) the packet sequence numbers. Define a new a flag bit for the post send table to identify local operations. Add a new field to the QP structure to track the number of local operations on the send queue to determine if direct processing of new local operations should be enabled/disabled. Reviewed-by:
-
Jianxin Xiong authored
In order to support extended memory management, add the mechanism to invalidate MR keys. This includes a flag "lkey_invalid" in the MR data structure that is to be checked when validating access to the MR via the associated key, and two utility functions to perform fast memory registration and memory key invalidate operations. Reviewed-by:
-
Jianxin Xiong authored
This implements the device specific function needed by the verbs API function ib_map_mr_sg(). Reviewed-by:
-
Mitko Haralanov authored
There were multiple places where FECN/BECN processing was being done for the different types of QPs. All of that code was very similar, which meant that it could be pulled into a single function used by the different QP types. To retain the performance in the fastpath, the common code starts with an inline function, which only calls the slow path if the packet has any of the [FB]ECN bits set. Reviewed-by:
Mitko Haralanov <mitko.haralanov@intel.com> Signed-off-by:
-
Tymoteusz Kielan authored
While handling buffer control MAD, partially initialized dd->kernel_send_context area may cause potential dereference of uninitialized pointers. Fix by using kzalloc_node() instead of kmalloc_node(). Reviewed-by:
Andrzej Kacprowski <andrzej.kacprowski@intel.com> Signed-off-by:
Tymoteusz Kielan <tymoteusz.kielan@intel.com> Signed-off-by:
-
Jakub Pawlak authored
PMA should not sum TX and RX replay counts when reporting local link integrity errors. Fixed by removing C_DC_TX_REPLAY counter from calculation of the link integrity errors counter value. Reviewed-by:
Ira Weiny <ira.weiny@intel.com> Reviewed-by:
Jakub Pawlak <jakub.pawlak@intel.com> Signed-off-by:
-
Mike Marciniszyn authored
Change rvt_post_one_wr to use the new table mechanism for post send. Validate that each low level driver specifies the table. Reviewed-by:
-
Mike Marciniszyn authored
Add initial table for table driven post_send support. Reviewed-by:
-
Mike Marciniszyn authored
Add initial table for table driven post_send support. Reviewed-by:
-
Mike Marciniszyn authored
Add flexibility for driver dependent operations in post send because different drivers will have differing post send operation support. This includes data structure definitions to support a table driven scheme along with the necessary validation routine using the new table. Reviewed-by:
-
Jakub Pawlak authored
Prevent processing receive packet in case when opcode is accepted by QP but handler for this type of packet is not defined. Reviewed-by:
-
Jianxin Xiong authored
Currently each user context is assigned a single SDMA engine based on the VL, context id, and subcontext id. That means for MPI applications, each rank can only use one SDMA engine for all messages. This may create unwanted backup for independent messages going to different destinations upon congestion at one destination. This patch adds the packet "dlid" to the formula of SDMA engine selection for user SDMA requests. A simple hash table is used to maintain even distribution among the available SDMA engines regardless how the "dlid" values are distributed. Reviewed-by:
-
Dean Luick authored
Remove the TWSI code. The driver now uses the kernel's built-in i2c bit bus module. Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by:
-
Dean Luick authored
Use built-in i2c bit-shift bus adapter to control the i2c busses on the chip. Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by:
-
Sebastian Sanchez authored
When performing process affinity recommendations for MPI ranks, the current algorithm doesn't take into account multiple HFI units. Also, real cores and HT cores are not distinguished from one another. Therefore, all HT cores are recommended to be assigned first within the local NUMA node before recommending the assignments of cores in other NUMA nodes. It's ideal to assign all real cores across all NUMA nodes first, then all HT 1 cores, then all HT 2 cores, and so on to balance CPU workload. CPU cores in other NUMA nodes could be running interrupt handlers, and this is not taken into account. To balance the CPU workload for user processes, the following recommendation algorithm is used: For each user process that is opening a context on HFI Y: a) If all cores are assigned to user processes, start assignments all over from the first core b) Assign real cores first, then HT cores (First set of HT cores on all physical cores, then second set of HT cores, and, so on) in the following order: 1. Same NUMA node as HFI Y and not running an IRQ handler 2. Same NUMA node as HFI Y and running an IRQ handler 3. Different NUMA node to HFI Y and not running an IRQ handler 4. Different NUMA node to HFI Y and running an IRQ handler c) Mark core as assigned in the global affinity structure. As user processes are done, remove core assignments from global affinity structure. This implementation allows an arbitrary number of HT cores and provides support for multiple HFIs. This is being included in the kernel rather than user space due to the fact that user space has no way of knowing the CPU recommendations for contexts running as part of other jobs. Reviewed-by:
Sebastian Sanchez <sebastian.sanchez@intel.com> Signed-off-by:
-
Sebastian Sanchez authored
Kernel receive queues oversubscribe CPU cores on multi-HFI systems. To prevent this, the kernel receive queues are separated onto different cores, and the SDMA engine interrupts are constrained to a lesser number of cores. hfi1s_on_numa_node*krcvqs is the number of CPU cores that are reserved for kernel receive queues for all HFIs. Each HFI initializes its kernel receive queues to one of the reserved CPU cores. If there ends up being 0 CPU cores leftover for SDMA engines, use the same CPU cores as receive contexts. In addition, general and control contexts are assigned to their own CPU core, however, both types of contexts tend to have low traffic. To save CPU cores, collapse general and control contexts to one CPU core for all HFI units. This change prevents SDMA engine interrupts from wrapping around general contexts. Reviewed-by:
-
Dennis Dalessandro authored
When HFI units get initialized, they each use their own mask copy for affinity assignments. On a multi-HFI system, affinity assignments overbook CPU cores as each HFI doesn't have knowledge of affinity assignments for other HFI units. Therefore, some CPU cores are never used for interrupt handlers in systems with high number of CPU cores per NUMA node. For multi-HFI systems, SDMA engine interrupt assignments start all over from the first CPU in the local NUMA node after the first HFI initialization. This change allows assignments to continue where the last HFI unit left off. Add global structure for affinity assignments for multiple HFIs to share affinity mask. Reviewed-by:
Jubin John <jubin.john@intel.com> Reviewed-by:
-
Jakub Pawlak authored
Add sw counter to track dropped unsupported packets. Report unsupported packets drop as the RcvError. Reviewed-by:
-
Jakub Pawlak authored
Add per VL XmitDiscards counters to the opapmaquery status and error response. Reviewed-by:
-
Mike Marciniszyn authored
Fix sparse errors by making sure the fast assign destinations are host cpu typed. For the void __iomem *, just make the field match source data. Fix a bug where the hw_free trace printed the pointer vs. the dereferenced value. Reviewed-by:
-
Sebastian Sanchez authored
The ftrace infrastructure used to evaluate the TRACE_SYSTEM macro on every DEFINE_EVENT() macro. Now the TRACE_SYSTEM macro only gets evaluated when trace/define_trace.h is included, so the group event information is lost. This was introduced in commit acd388fd ("tracing: Give system name a pointer") Therefore, each system tracepoint must be on its own file. Reviewed-by:
-
Tadeusz Struk authored
Fix a copy and paste typo in comment. Reviewed-by:
-
Ira Weiny authored
Simple code clean up of hfi1_write_iter. Reviewed-by:
-
Ira Weiny authored
The definition of port state changed mid development and the old structure was kept accidentally. Remove this dead code. Reviewed-by:
-
- 24 Jul, 2016 1 commit
-
-
Linus Torvalds authored
-
