The original message was unhelpful and extremely alarming to our poor
users, despite its charm. Make it less frightening.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Optimize the lightly loaded case, by only synchronizing discards stats
when qlen > 10 indicate potential for drops.

Notice Robert Olsson might disagree with this patch.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Discard packet counter debug statements that can be turned on
at runtime by users to assist debugging of the driver code.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implementing discard counters for the NIU driver turned out to be more
complicated than first assumed.

The discard counters for the NIU neptune chip are only 16-bit (even
though this is a 64-bit chip).  These 16-bit counters can overflow
quickly, especially considering this is a 10Gbit/s ethernet card.

The overflow indication bit is, unfortunatly, not usable as the
counter value does not wrap, but remains at max value 0xFFFF.
Resulting in lost counts until the counter is reset.

The read and reset scheme also poses a problem. Both in theory and in
practice counters can be lost in between reading nr64() and clearing
the counter nw64().  For this reason, the number of counter clearings
nw64() is limited/reduced.  On the fast-path the counters are only
syncronized once it exceeds 0x7FFF.  When read by userspace, its
syncronized fully.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

A major source of overhead in the enc28j60 driver is the SPI transfers. Each
SPI transfer entails two kernel thread context switches. One major source of
SPI transfers is the enc28j60_set_bank() functions which runs before every
register access. This patch reduces the number of SPI transfers that
enc28j60_set_bank() performs in two ways:

  1. removes unnecessary bank switch for the registers that are present in all
	 banks

  2. when switching from banks 0 or 3 to banks 1 or 2 (i.e. only one bit
	 changes) enc28j60_set_bank() does only one SPI transfer instead of two

According to my tests these changes reduce the number of SPI transfers in
about 25%.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

| commit 3d29b0c3
| Author: John W. Linville <linville@tuxdriver.com>
| Date:   Fri Oct 31 14:13:12 2008 -0400
|
|     netdevice zd1201: Convert directly reference of netdev->priv to netdev_priv()
|
|     We have some reasons to kill netdev->priv:
|     1. netdev->priv is equal to netdev_priv().
|     2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
|        netdev_priv() is more flexible than netdev->priv.
|     But we cann't kill netdev->priv, because so many drivers reference to it
|     directly.
|
|     OK, becasue Dave S. Miller said, "every direct netdev->priv usage is a bug",
|     and I want to kill netdev->priv later, I decided to convert all the direct
|     reference of netdev->priv first.
|
|     (Original patch posted by Wang Chen <wangchen@cn.fujitsu.com> w/ above
|     changelog but using dev->ml_priv.  That doesn't seem appropriate
|     to me for this driver, so I've revamped it to use netdev_priv()
|     instead. -- JWL)

This commit changed the allocation of netdev, but didn't change
the free method of it.
This causes "zd" be used after the memory, which is pointed by "zd", being
freed by free_netdev().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit e061b165.
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 70355602.

As pointed out by Mark McLoughlin IP_PKTINFO cmsg data is one
post-queueing user, so this optimization is not valid right
now.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

I also removed some of the unneeded braces in the if condition to
improve readability and a little bit of reformatting.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

They are all defined before used, it's therefore ok to remove
them.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Also remove the pointless comment at the top.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

It helps in maintaining the various partner information values from
the LACPDU.  It also removes the pointless comment at the top.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

It generally helps to handle those values in various places, using it
might make the code more readable and gives room for other improvements.

The IEEE standard talks about them as "parameter values".
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous code was just a funny way of assigning both values (they
are both of type u8).
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

gfar_poll would declare polling done once the rx queue was empty,
but the tx queue could still have packets left.

Stolen mostly from the e1000 driver.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No clean up function is executed in the interrupt context by this patch.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Interface name (ex. eth0) is used as the prefix for the interrupt name,
with _rx, _tx, and _er appended to distinguish multiple interrupts on
the same interface.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Scatter Gather support in gianfar driver to handle fragmented frames on
the transmit side.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch which fixed gianfar so it drops packets when it runs out
of memory left in the code which frees the skb when it drops packets.
Change the code so that we only free the skb if the new skb was successfully
created.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

And thus when we try to use 'ss -danemi' on these sockets that have no
ccid blocks (data collected using systemtap after I fixed the problem):

dccp_diag_get_info sk=0xffff8801220a3100, dp->dccps_hc_rx_ccid=0x0000000000000000, dp->dccps_hc_tx_ccid=0x0000000000000000

We get an OOPS:

mica.ghostprotocols.net login: BUG: unable to handle kernel NULL pointer
dereferenc0
IP: [<ffffffffa0136082>] dccp_diag_get_info+0x82/0xc0 [dccp_diag]
PGD 12106f067 PUD 122488067 PMD 0
Oops: 0000 [#1] PREEMPT

Fix is trivial, and 'ss -d' is working again:

[root@mica ~]# ss -danemi
State   Recv-Q Send-Q   Local Address:Port   Peer Address:Port 
LISTEN  0      0                    *:5001              *:*
ino:7288 sk:220a3100ffff8801
	 mem:(r0,w0,f0,t0) cwnd:0 ssthresh:0
[root@mica ~]# 
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This implements the Nokia vendor-specific communication device class
function to exchange Phonet messages over USB. This function is already
found in the "PC suite" USB profile of (non-Linux) Nokia handsets.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

GPRS TX flow control won't need to lock the underlying socket anymore.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A separate xmit lock class supports GPRS over a Phonet pipe over a TUN
device (type ARPHRD_NONE).
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Also leave some room for more 802.11 types.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use idr technique instead of own implemented cardmaps.
It saves us a number of lines and gives an ability
to use library functions.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

These are now defined in linux/mii.h and the bnx2x driver
defines different values which are shared with hardware
data structures.

So add a "BNX2X_" prefix to these macro names.

Based upon a report from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>

They are provided generically by linux/mii.h now.
Signed-off-by: David S. Miller <davem@davemloft.net>

And fix the 5716S pci_device_id entry to point to the proper string.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change MSI-X vector names to "ethx-%d".
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@

- T i = E->fld;
+ T i;
  ... when != E
      when != i
  if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

genphy_setup_forced hasn't actually reset the PHY for a long time,
but a comment to that effect remained in the code, so code continued
to act as if it *had* reset the PHY, and called the necessary fixup
functions to respond to a PHY reset.  With no reset, those functions
are no longer needed, so we remove them.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Whenever we want to update the status field in a BD, we usually want to
update the length field, too.  By combining them into one 32-bit field, we
reduce the number of stores to memory shared with the controller, and we
eliminate the need for order-enforcement, as the length and "READY" bit are
now updated atomically at the same time.
Signed-off-by: Dai Haruki <Dai.Haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This code is based strongly on code from Dai Haruki <Dai.Haruki@freescale.com>.

The gianfar Buffer Descriptors are arranged in a circular array, the end of
which is denoted by setting the "WRAP" bit in the descriptor.  However, the
software knows the end of the ring because it knows how many descriptors are
there.  Rather than check each descriptor for whether the WRAP bit is set,
use pointer math to determine where the next BD is.  This is also useful for
when we want to look at BDs other than the very next one (for Scatter-Gather).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Also, use cacheable_memzero instead of memset for performance reasons.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The eTSEC can prepend up to 32 bytes to a received frame, usually for the
purpose of aligning the IP address to a word boundary, so this turns it on.

While we're in there, make the handling of the pre-frame bytes (padding and
Frame Control Block) cleaner.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>