This implements various helpers to support OF bindings for the i2c
API.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This implements support for the GPIO LIB API.  Two calls are still
unimplemented though: irq_to_gpio and gpio_to_irq.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This implements various helpers to support OF bindings for the GPIO
LIB API.

Previously this was PowerPC specific, but it seems this code isn't
arch-dependent anyhow, so let's place it into of/.

SPARC will not see this addition yet, real hardware seem to not use
GPIOs at all. But this might change:

   http://www.leox.org/docs/faq_MLleon.html

"16-bit I/O port" sounds promising. :-)
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The iSeries veth driver uses an on-stack struct completion that
it initializes using the COMPLETION_INITIALIZER instead of
COMPLETION_INITIALIZER_ONSTACK macro, causing problems with
lockdep.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This fixes the handling of the preempt count when switching
interrupt stacks so that HW interrupt properly get the softirq
mask copied over from the previous stack.

It also initializes the softirq stack preempt_count to 0 instead
of SOFTIRQ_OFFSET, like x86, as __do_softirq() does the increment,
and we hit some lockdep checks if we have it twice.

That means we do run for a little while off the softirq stack
with the preempt-count set to 0, which could be deadly if we
try to take a softirq at that point, however we do so with
interrupts disabled, so I think we are ok.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Currently, we initialize the "current" pointer in the PACA (which
is used by the "current" macro in the kernel) before calling
setup_system(). That means that early_setup() is called with
current still "NULL" which is -not- a good idea. It happens to
work so far but breaks with lockdep when early code calls printk.

This changes it so that all PACAs are statically initialized with
__current pointing to the init task. For non-0 CPUs, this is fixed
up before use.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This fixes a potential bug at drivers/char/hvc_beat.c.
 - hvc_put_term_char routine will decrement "rest" variable twice,
   and forget to advance "buf" pointer by "nlen" bytes.
This bug was not hit previously because the output handler in
drivers/char/hvc_console.c splits given output into 16 bytes
at maximum.
Reported-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This changes the cpu_idle loop for 44x platforms to utilize the Wait Enable
feature of the CPU.  This helps virtulization solutions know when the guest
Linux kernel is in an idle state.

A command line option called "idle" is also added to allow people to change
the idle loop back to the original variation.  This is done by setting
"idle=spin" on the kernel command line.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

Add a multi-board PowerPC 40x defconfig file
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

Board specific defconfigs are useful, however with the ability to do
multi-board defconfigs they aren't needed in the top level configs directory.

Move the 4xx board specific defconfigs to individual directories under
arch/powerpc/configs.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

There is a potential bug in __lmb_alloc_base where we subtract `size'
from the base address of a reserved region without checking whether
the subtraction could wrap around and produce a very large unsigned
value.  In fact it probably isn't possible to hit the bug in practice
since it would only occur in the situation where we can't satisfy the
allocation request and there is a reserved region starting at 0.

This fixes the potential bug by breaking out of the loop when we get
to the point where the base of the reserved region is less than the
size requested.  This also restructures the loop to be a bit easier to
follow.

The same logic got copied into lmb_alloc_nid_unreserved, so this makes
a similar change there.  Here the bug is more likely to be hit because
the outer loop  (in lmb_alloc_nid) goes through the memory regions in
increasing order rather than decreasing order as __lmb_alloc_base
does, and we are therefore more likely to hit the case where we are
testing against a reserved region with a base address of 0.
Signed-off-by: Paul Mackerras <paulus@samba.org>

This makes no semantic changes.  It fixes the whitespace and formatting
a bit, gets rid of a local DBG macro and uses the equivalent pr_debug
instead, and restructures one while loop that had a function call and
assignment in the condition to be a bit more readable.  Some comments
about functions being called with relocation disabled were also removed
as they would just be confusing to most readers now that the code is
in lib/.
Signed-off-by: Paul Mackerras <paulus@samba.org>

A variant of lmb_alloc() that tries to allocate memory on a specified
NUMA node 'nid' but falls back to normal lmb_alloc() if that fails.

The caller provides a 'nid_range' function pointer which assists the
allocator.  It is given args 'start', 'end', and pointer to integer
'this_nid'.

It places at 'this_nid' the NUMA node id that corresponds to 'start',
and returns the end address within 'start' to 'end' at which memory
assosciated with 'nid' ends.

This callback allows a platform to use lmb_alloc_nid() in just
about any context, even ones in which early_pfn_to_nid() might
not be working yet.

This function will be used by the NUMA setup code on sparc64, and also
it can be used by powerpc, replacing it's hand crafted
"careful_allocation()" function in arch/powerpc/mm/numa.c

If x86 ever converts it's NUMA support over to using the LMB helpers,
it can use this too as it has something entirely similar.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

pmi.h does not diectly reference anything in of_device.h and of the two
files that include asm/pmi.h, one includes of_device.h and the other
includes of_platform.h (which includes of_device.h).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Now that we have the alpaca, the reg_save_ptr is no longer needed in the
paca.  Eradicate all global uses of it and make it static in the iSeries
lpardata.c
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The iSeries HV only needs the first two fields of the paca statically
initialised, so create an alternate paca that contains only those and
switch to our real paca immediately after boot.

This is in order to make the 1024 cpu patches easier since they will no
longer have to statically initialise the pacas for iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The prpmc2800 platform requires a zImage formatted file with an
embedded dtb file.  Rename the requested boot image file to
dtbImage.prpmc2800.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Add the device tree bindings for the Marvell mv64x60 series of
system controller chips in booting-without-of.text.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The mv643xx_eth driver is being modified to support multiple instances
of the ethernet silicon block on the same platform.  Each block contains
a single register bank containing the registers for up to three ports
interleaved within that bank.  This patch updates the PowerPC OF to
platform_device glue code to support multiple silicon blocks, each
with up to three ethernet ports.  The main difference is that we now
allow multiple mv64x60_shared platform_devices to be registered and
we provide each port platform_device with a pointer to its associated
shared platform_device.  The pointer will not be used until the
mv643xx_eth driver changes are committed.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Remove several unused (or software config only) properties.
Rename marvel node to "system-controller".  Also, rename the
"block-index" property to "cell-index" to conform to current
practice.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Replace several device node absolute path lookups in the mv64x60
bootwrapper code with lookups by compatible or device_type
properties.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Compatible names should refer to a specific version of the hardware,
without wildcards.  Change each instance of mv64x60 to mv64360, which
is the oldest version we currently support.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

After the conversion to dts v1 format, seeing the frequencies
in decimal made it obvious that some of them had been
incorrectly truncated.  This fixes them.  Note that the PCI
frequency comes from a different source and is documented
as 66MHz, so it was left at 66000000.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Update the prpmc2800 DTS file to version 1 and add labels.
I verified that there was no change in the resulting dtb file.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The allyesconfig (among others) build was giving this:

In file included from include/linux/gfp.h:4,
                 from include/linux/slab.h:14,
                 from include/linux/percpu.h:5,
                 from include2/asm/time.h:18,
                 from include2/asm/cputime.h:26,
                 from include/linux/sched.h:67,
                 from
arch/powerpc/kernel/asm-offsets.c:17:
include/linux/mmzone.h:791:2: error: #error Allocator MAX_ORDER exceeds SECTION_SIZE

Kconfig options are order depenendent, so move the setting of
FORCE_MAX_ZONEORDER to after the setting of PPC_64K_PAGES. Also add an
explicit !PPC_64K_PAGES.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

If an SLB miss interrupt happens while the RI bit of MSR is zero, we
can't just return, because RI being zero indicates that SRR0/SRR1
potentially had live values in them, and the process of taking an
interrupt overwrites them.

This should never happen, but if it does, we try to print a nice oops
message.  That doesn't work, however, because the code at unrecov_slb
assumes that the MMU has been turned on, but we call it with the MMU
off (and have done so since the SLB miss handler was rewritten to run
without turning the MMU on) -- except on iSeries, where everything runs
with the MMU on.

This fixes it by adding the necessary code to turn the MMU on if
necessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>

* 'docs' of git://git.lwn.net/linux-2.6:
  Add additional examples in Documentation/spinlocks.txt
  Move sched-rt-group.txt to scheduler/
  Documentation: move rpc-cache.txt to filesystems/
  Documentation: move nfsroot.txt to filesystems/
  Spell out behavior of atomic_dec_and_lock() in kerneldoc
  Fix a typo in highres.txt
  Fixes to the seq_file document
  Fill out information on patch tags in SubmittingPatches
  Add the seq_file documentation

Checkpatch will throw an error if code doesn't use the correct initializers
for static spinlocks:

ERROR: Use of SPIN_LOCK_UNLOCKED is deprecated: see Documentation/spinlocks.txt

This is fine, but Documentation/spinlocks.txt isn't very clear on how to
_use_ the new initializers for static variables. To save people time in the
future, I added two small examples of how to fix old-style static
initializers to be more lockdep friendly.
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

This file is nfs-related.  (Maybe Documentation/filesystems/ would
benefit from a separate nfs/ directory at some point.)
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

Documentation/ is a little large, and filesystems/ seems an obvious
place for this file.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

A little more detail here wouldn't hurt.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

git commit 54a01510 ("asmlinkage_protect
replaces prevent_tail_call") causes this build failure on s390:

    AS      arch/s390/kernel/entry64.o
  In file included from arch/s390/kernel/entry64.S:14:
  include/linux/linkage.h:34: error: syntax error in macro parameter list
  make[1]: *** [arch/s390/kernel/entry64.o] Error 1
  make: *** [arch/s390/kernel] Error 2

and some other architectures.  The reason is that some architectures add
the "-traditional" flag to the invocation of $(AS), which disables
variadic macro argument support.

So just surround the new define with an #ifndef __ASSEMBLY__ to prevent
any side effects on asm code.

Cc: Roland McGrath <roland@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c-tiny-usb: New VID/PID pair
  i2c-davinci: Fix lost interrupt
  i2c-ibm_iic: Fast mode parm desc fixup