The major VIA issues were handled by the quirks update for resume quirks.
The ATA driver also has to do some work however when resuming from RAM.
Certain chips need the FIFO reconfiguring, and the 66MHz clock setup
updating.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Early AMD chips require FIFO and/or simplex flag clearing work on resume
from RAM. Most devices need no help
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

If you are using the noraid option then after a suspend/resume sequence
we need to reset the card back out of raid mode again.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The Serverworks chips need various fixups doing on a resume from RAM.
Conveniently the needed functions were already split out ready for re-use
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

On a resume of the CMD64x we must restore MRDMODE and latency if the BIOS
didn't get them right originally.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The CS5520 doesn't need much help to resume but we do need to restore
pcicfg which may have been reset to the BIOS default which is
sometimes incorrect.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch adds the suspend/resume callbacks for drivers which don't need
any additional help (beyond the pci resume quirk patch I posted earlier
anyway). Also bring version numbers back inline with master copies.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The SI680 can come back from s2ram with the clocks disabled (crash time)
or wrong (ugly as this can cause CRC errors, and in theory corruption).
On a resume we must put the clock back.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The RZ1000 is a generic device except that it has a readahead fifo flaw
that corrupts. We force this off at init time but we want to be paranoid
and force it off at resume as well. I don't know of any actual hardware
that supports both RZ1000 and suspend to RAM but given its a disk muncher
better safe than sorry.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Various chipset functions must be reprogrammed on a resume from RAM,
without this things like ATAPI DMA stop working on resume with some
chipset variants. Split the chipset programming and init time method selection into two functions.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This (and the pci resume quirk code) get the JMicron controllers to
resume properly. Without this patch the drive mapping changes when you
suspend/resume which is not good at all....
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The 5530 needs various set up performing both at init time and resume
time. To keep the code clean the common setup code is moved into a new
function and called from both handlers.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

More enablebits
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch updates the sata_promise driver as follows:
- Correct typo in definition of PDC_TBG_MODE: it's at 0x41C not 0x41
  in first-generation chips. This error caused PCI access alignment
  exceptions on SPARC64, and on all platforms it disabled the expected
  initialisation of TBG mode.
- Add flags field to struct pdc_host_priv. Define PDC_FLAG_GEN_II
  and use it to distinguish first- and second-generation chips.
- Prevent the FLASH_CTL FIFO_SHD bit from being set to 1 on second-
  generation chips. This matches Promises' ulsata2 driver.
- Prevent TBG mode and SLEW rate initialisation in second-generation chips.
  These two registers have moved, TBG mode has been redefined, and
  Promise's ulsata2 driver no longer attempts to initialise them.
- Correct PCI device table so devices 0x3570, 0x3571, and 0x3d73 are
  marked as 2057x (2nd gen) not 2037x (1st gen).
- Correct PCI device table so device 0x3d17 is marked as 40518
  (2nd gen 4 ports) not 20319 (1st gen 4 ports).
- Correct pdc_ata_init_one() to treat 20771 as a second-generation chip.

Tested on 0x3d75 (2nd gen), 0x3d73 (2nd gen), and 0x3373 (1st gen) chips.
The information comes from the newly uploaded Promise SATA HW specs,
Promise's ultra and ulsata2 drivers, and debugging on 3d75/3d73/3373 chips.

hp->hotplug_offset could now be removed and its value recomputed
in pdc_host_init() using hp->flags, but that would be a cleanup
not a functional change, so I'm ignoring it for now.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Fixes crashes on sparc, and may correct weird behavior reported on
occasions, because we were never programming this register correctly (or
at all).
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Update ata_gen_ata_sense() to use desc format sense data to report the
first failed block.  The first failed block is read from result_tf
using ata_tf_read_block() which can handle all three address formats.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Implement ata_tf_read_block().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* s/ata_gen_ata_desc_sense/ata_gen_passthru_sense/

* s/ata_gen_fixed_sense/ata_gen_ata_sense/

* make both functions static

* neither function has locking requirement, change it to None.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

sb[7] should contain the length of whole information sense data
descriptor while desc[1] should contain the number of following bytes
in the descriptor.  ie. 14 for sb[7] but 12 for desc[1].
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

libata didn't initialize result_tf.flags which indicates transfer type
(RW/FUA) and address type (CHS/LBA/LBA48).  ata_gen_fixed_sense()
assumed result_tf.flags equals command tf.flags and failed to report
the first failed block to SCSI layer because zero tf flags indicates
CHS and bad block reporting for CHS is not implemented.

Implement fill_result_tf() which sets result_tf.flags to command
tf.flags and use it to fill result_tf.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

There's no need to memset &qc->sgent manually, sg_init_one() clears
sgent inside it.  Also, kill not-so-necessary sg local variable.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Improve failed qc reporting.  The original message didn't include the
actual command nor full error status and it was necessary to
temporarily patch the code to find out exactly which command is
causing problem.  This patch makes EH report full command and result
TFs along with data direction and length.  This change will make bug
reports more useful.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Now that PCS isn't used for device detection anymore...

* esb_sata is identical to ich5_sata
* no reason to know present_shift
* no reason to store map_db in host private area

The MAP table itself is left because it can be used for SCR access.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

PATA PIIX uses reset signature + TF r/w test for device presence
detection, which doesn't always work.  It sometimes reports phantom
device which results in IDENTIFY timeouts.

SATA PIIX uses some combination of PCS + reset signature + TF r/w test
for device presence detection.  No combination satifies all and for
some controllers, there doesn't seem to be any combination which
works reliably.

This patch makes both PATA and SATA piix's use reset signature + TF
r/w + polling IDENTIFY for device detection.  This is what the old
libata (before irq-pio and new EH) did and what IDE does.

This patch also removes now obsolete PIIX_FLAG_IGNORE_PCS, force_pcs
and related code.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

On some controllers (ICHs in piix mode), there is *NO* reliable way to
determine device presence other than issuing IDENTIFY and see how the
transaction proceeds by watching the TF status register.

libata acted this way before irq-pio and phantom devices caused very
little problem but now that IDENTIFY is performed using IRQ drive PIO,
such phantom devices now result in multiple 30sec timeouts during
boot.

This patch implements ATA_FLAG_DETECT_POLLING.  If a LLD sets this
flag, libata core issues the initial IDENTIFY in polling mode and if
the initial data transfer fails w/ HSM violation, the port is
considered to be empty thus replicating the old libata and IDE
behavior.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Make ata_dev_read_id() take @flags instead of @post_reset.  Currently
there is only one flag defined - ATA_READID_POSTRESET, which is
equivalent to @post_reset.  This is preparation for polling presence
detection.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* move common flags into PIIX_PATA_FLAGS and PIIX_SATA_FLAGS
* kill unnecessary ATA_FLAG_SRST
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Many drives support LBA48 even when its capacity is smaller than
1<<28, as LBA48 is required for many functionalities.  FLUSH_EXT is
mandatory for drives w/ LBA48 support.

Interestingly, at least one of such drives (ST960812A) has problems
dealing with FLUSH_EXT.  It eventually completes the command but takes
around 7 seconds to finish in many cases thus drastically slowing down
IO transactions.  This seems to be a firmware bug which sneaked into
production probably because no other ATA driver including linux IDE
issues FLUSH_EXT to drives which report support for LBA48 & FLUSH_EXT
but is smaller than 1<<28 blocks.

This patch adds ATA_DFLAG_FLUSH_EXT which is set iff the drive
supports LBA48 & FLUSH_EXT and is larger than LBA28 limit.  Both cache
flush paths are updated to issue FLUSH_EXT only when the flag is set.
Note that the changed behavior is more inline with the rest of libata.
libata prefers shorter commands whenever possible.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Danny Kukawka <dkukawka@novell.com>
Cc: Stefan Seyfried <seife@novell.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Some ICH8s use non-linear port mapping.  ahci driver didn't use to
honor PORTS_IMPL and this made ports after hole nonfunctional.  This
patch makes ahci mark those ports as dummy and properly initialize all
the implemented ports after the dummies.

As it's unknown whether other AHCIs implement PORTS_IMPL register
properly, new board id board_ahci_pi is added and selectively applied
to ICH8s.  All other AHCIs continue to use linear mapping regardless
of PORTS_IMPL value.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

SiS965 and SiS180 chips must support slave mode,
SiS965L and SiS964 chips must not support slave mode.

SCR_STATUS for SATA ports in powerdown state fixed.
Now returning 0x0113 instead of 0x0117. Avoids problem
on detecting sata_sis controller.
Signed-off-by: Uwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Instead of writing 0xf blindly, preserve the content of write-once
PORTS_IMPL register over host resets.

This patch is taken from Jeff Garzik's AHCI init update patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

pdc_* functions are part of the global namespace for the PDC on PA-RISC
systems and this means our choice of pdc_ causes collisions between the
PDC globals and our static functions. Rename them to pdc202xx where they
are for both 2024x and 2026x.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Jeff Garzik <jeff@garzik.org>

Move dev->max_sectors configuration from ata_scsi_dev_config() to
ata_dev_configure().

* more consistent.
* allows LLDs to peek at the default dev->max_sectors value.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

libata EH used to perform ata_set_mode() iff the EH session performed
reset as indicated by ATA_EHI_DID_RESET.  This is incorrect because
->dev_config() called by revalidation is allowed to modify transfer
mode which ata_set_mode() should take care of.  This patch implements
the following two flags.

* ATA_EHI_SETMODE: set during EH to schedule ata_set_mode().  Both new
  device attachment and revalidation set this flag.

* ATA_EHI_POST_SETMODE: set while the device is revalidated after
  ata_set_mode().  Post-setmode revalidation is different from initial
  configuaration and EH revalidation in that ->dev_config() is not
  allowed tune transfer mode.  LLD can use this flag to determine
  whether it's allowed to tune transfer mode.  Note that POST_SETMODE
  ->dev_config() is guaranteed to be preceded by non-POST_SETMODE
  ->dev_config().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Implement ehi flag ATA_EHI_PRINTINFO.  This flag is set when device
configuration needs to print out device info.  This used to be handled
by @print_info argument to ata_dev_configure() but LLDs also need to
know about it in ->dev_config() callback.

This patch replaces @print_info w/ ATA_EHI_PRINTINFO and make sata_sil
print workaround messages only on the initial configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ahci-vt8251

* requires hardreset after PHY status change

* doesn't clear BSY on signature FIS after hardreset

* needs SError cleared for the port to operate after hardreset

This patch implements ahci_vt8251_hardreset() and sets
ATA_FLAG_HRST_TO_RESUME to handle the above behaviors.  This fixes EH
including hotplug on vt8251.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Separate out sata_port_hardreset() from sata_std_hardreset().  This
will be used by LLD hardreset implementation and later by PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Now that ahci_softreset() is fixed to automatically perform CLO if
BSY/DRQ is set on entry, AHCI_FLAG_RESET_NEEDS_CLO is redundant.  Kill
it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>