[ Upstream commit 4c4e3731 ]

Notable cmpxchg() does not provide ordering when it fails, however
wake_q_add() requires ordering in this specific case too. Without this
it would be possible for the concurrent wakeup to not observe our
prior state.

Andrea Parri provided:

  C wake_up_q-wake_q_add

  {
	int next = 0;
	int y = 0;
  }

  P0(int *next, int *y)
  {
	int r0;

	/* in wake_up_q() */

	WRITE_ONCE(*next, 1);   /* node->next = NULL */
	smp_mb();               /* implied by wake_up_process() */
	r0 = READ_ONCE(*y);
  }

  P1(int *next, int *y)
  {
	int r1;

	/* in wake_q_add() */

	WRITE_ONCE(*y, 1);      /* wake_cond = true */
	smp_mb__before_atomic();
	r1 = cmpxchg_relaxed(next, 1, 2);
  }

  exists (0:r0=0 /\ 1:r1=0)

  This "exists" clause cannot be satisfied according to the LKMM:

  Test wake_up_q-wake_q_add Allowed
  States 3
  0:r0=0; 1:r1=1;
  0:r0=1; 1:r1=0;
  0:r0=1; 1:r1=1;
  No
  Witnesses
  Positive: 0 Negative: 3
  Condition exists (0:r0=0 /\ 1:r1=0)
  Observation wake_up_q-wake_q_add Never 0 3
Reported-by: Yongji Xie <elohimes@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6dc080ee ]

For some peculiar reason rcuwait_wake_up() has the right barrier in
the comment, but not in the code.

This mistake has been observed to cause a deadlock in the following
situation:

    P1					P2

    percpu_up_read()			percpu_down_write()
      rcu_sync_is_idle() // false
					  rcu_sync_enter()
					  ...
      __percpu_up_read()

[S] ,-  __this_cpu_dec(*sem->read_count)
    |   smp_rmb();
[L] |   task = rcu_dereference(w->task) // NULL
    |
    |				    [S]	    w->task = current
    |					    smp_mb();
    |				    [L]	    readers_active_check() // fail
    `-> <store happens here>

Where the smp_rmb() (obviously) fails to constrain the store.

[ peterz: Added changelog. ]
Signed-off-by: Prateek Sood <prsood@codeaurora.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 8f95c90c ("sched/wait, RCU: Introduce rcuwait machinery")
Link: https://lkml.kernel.org/r/1543590656-7157-1-git-send-email-prsood@codeaurora.orgSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a0dc0203 ]

In ieee80211_rx_h_mesh_fwding, we increment the 'dropped_frames_ttl'
counter when we decrement the ttl to zero.  For unicast frames
destined for other hosts, we stop processing the frame at that point.

For multicast frames, we do not rebroadcast it in this case, but we
do pass the frame up the stack to process it on this STA.  That
doesn't match the usual definition of "dropped," so don't count
those as such.

With this change, something like `ping6 -i0.2 ff02::1%mesh0` from a
peer in a ttl=1 network no longer increments the counter rapidly.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 97715058 ]

When CONFIG_NO_AUTO_INLINE was present in linux-next (which added
'-fno-inline-functions' to KBUILD_CFLAGS), an allyesconfig build with
Clang failed at the modpost stage:

ERROR: "is_broadcast_mac_addr" [drivers/staging/rtl8723bs/r8723bs.ko] undefined!
ERROR: "is_zero_mac_addr" [drivers/staging/rtl8723bs/r8723bs.ko] undefined!
ERROR: "is_multicast_mac_addr" [drivers/staging/rtl8723bs/r8723bs.ko] undefined!

These functions were marked as extern inline, meaning that if inlining
doesn't happen, the function will be undefined, as it is above.

This happens to work with GCC because the '-fno-inline-functions' option
respects the __inline attribute so all instances of these functions are
inlined as expected and the definition doesn't actually matter. However,
with Clang and '-fno-inline-functions', a function has to be marked with
the __always_inline attribute to be considered for inlining, which none
of these functions are. Clang tries to find the symbol definition
elsewhere as it was told and fails, which trickles down to modpost.

To make sure that this code compiles regardless of compiler and make the
intention of the code clearer, use 'static' to ensure these functions
are always defined, regardless of inlining. Additionally, silence a
checkpatch warning by switching from '__inline' to 'inline'.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 129699bb ]

Changes since V1:
* Use dev_info instead of printk
* Use dev_warn instead of BUG_ON

Previously, sysfs_create_group was called before all initialization had
fully run - specifically, before pci_set_drvdata was called. Since the
sysctl group is visible to userspace as soon as sysfs_create_group
returns, a small window of time existed during which a process could read
from an uninitialized/partially-initialized device.

This commit moves the creation of the sysctl group to after all
initialized is completed. This ensures that it's impossible for
userspace to read from a sysctl file before initialization has fully
completed.

To catch any future regressions, I've added a check to ensure
that proc_thermal_emum_mode is never PROC_THERMAL_NONE when a process
tries to read from a sysctl file. Previously, the aforementioned race
condition could result in the 'else' branch
running while PROC_THERMAL_NONE was set,
leading to a null pointer deference.
Signed-off-by: Aaron Hill <aa1ronham@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ab6c0367 ]

and use smaller/on-stack buffer instead

The motivation for this change was lockdep splat like below.

| potentially unexpected fatal signal 11.
| BUG: sleeping function called from invalid context at ../mm/page_alloc.c:4317
| in_atomic(): 1, irqs_disabled(): 0, pid: 57, name: segv
| no locks held by segv/57.
| Preemption disabled at:
| [<8182f17e>] get_signal+0x4a6/0x7c4
| CPU: 0 PID: 57 Comm: segv Not tainted 4.17.0+ #23
|
| Stack Trace:
|  arc_unwind_core.constprop.1+0xd0/0xf4
|  __might_sleep+0x1f6/0x234
|  __get_free_pages+0x174/0xca0
|  show_regs+0x22/0x330
|  get_signal+0x4ac/0x7c4     # print_fatal_signals() -> preempt_disable()
|  do_signal+0x30/0x224
|  resume_user_mode_begin+0x90/0xd8

So signal handling core calls show_regs() with preemption disabled but
an ensuing GFP_KERNEL page allocator call is flagged by lockdep.

We could have switched to GFP_NOWAIT, but turns out that is not enough
anways and eliding page allocator call leads to less code and
instruction traces to sift thru when debugging pesky crashes.

FWIW, this patch doesn't cure the lockdep splat (which next patch does).
Reviewed-by: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4e868f84 ]

|  CC      mm/nobootmem.o
|In file included from ./include/asm-generic/bug.h:18:0,
|                 from ./arch/arc/include/asm/bug.h:32,
|                 from ./include/linux/bug.h:5,
|                 from ./include/linux/mmdebug.h:5,
|                 from ./include/linux/gfp.h:5,
|                 from ./include/linux/slab.h:15,
|                 from mm/nobootmem.c:14:
|mm/nobootmem.c: In function '__free_pages_memory':
|./include/linux/kernel.h:845:29: warning: comparison of distinct pointer types lacks a cast
|   (!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
|                             ^
|./include/linux/kernel.h:859:4: note: in expansion of macro '__typecheck'
|   (__typecheck(x, y) && __no_side_effects(x, y))
|    ^~~~~~~~~~~
|./include/linux/kernel.h:869:24: note: in expansion of macro '__safe_cmp'
|  __builtin_choose_expr(__safe_cmp(x, y), \
|                        ^~~~~~~~~~
|./include/linux/kernel.h:878:19: note: in expansion of macro '__careful_cmp'
| #define min(x, y) __careful_cmp(x, y, <)
|                   ^~~~~~~~~~~~~
|mm/nobootmem.c:104:11: note: in expansion of macro 'min'
|   order = min(MAX_ORDER - 1UL, __ffs(start));

Change __ffs return value from 'int' to 'unsigned long' as it
is done in other implementations (like asm-generic, x86, etc...)
to avoid build-time warnings in places where type is strictly
checked.

As __ffs may return values in [0-31] interval changing return
type to unsigned is valid.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c530bb8a ]

The mbi_lock mutex is left uninitialized, so let's use DEFINE_MUTEX
to initialize it statically.

Fixes: 50528752 ("irqchip/gic-v3: Add support for Message Based Interrupts as an MSI controller")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 508cacd7 ]

With gcc 7.3.0:

    gpio-mockup-chardev.c: In function ‘get_debugfs’:
    gpio-mockup-chardev.c:62:3: warning: ignoring return value of ‘asprintf’, declared with attribute warn_unused_result [-Wunused-result]
       asprintf(path, "%s/gpio", mnt_fs_get_target(fs));
       ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Handle asprintf() failures to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5bbc73a8 ]

seccomp_bpf fails to build due to undefined reference errors:

 aarch64-linaro-linux-gcc --sysroot=/build/tmp-rpb-glibc/sysroots/hikey
 -O2 -pipe -g -feliminate-unused-debug-types -Wl,-no-as-needed -Wall
 -Wl,-O1 -Wl,--hash-style=gnu -Wl,--as-needed -lpthread seccomp_bpf.c -o
 /build/tmp-rpb-glibc/work/hikey-linaro-linux/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf
 /tmp/ccrlR3MW.o: In function `tsync_sibling':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1920: undefined reference to `sem_post'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1920: undefined reference to `sem_post'
 /tmp/ccrlR3MW.o: In function `TSYNC_setup':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1863: undefined reference to `sem_init'
 /tmp/ccrlR3MW.o: In function `TSYNC_teardown':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1904: undefined reference to `sem_destroy'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1897: undefined reference to `pthread_kill'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1898: undefined reference to `pthread_cancel'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1899: undefined reference to `pthread_join'
 /tmp/ccrlR3MW.o: In function `tsync_start_sibling':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
 /tmp/ccrlR3MW.o: In function `TSYNC_siblings_fail_prctl':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1978: undefined reference to `sem_wait'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1990: undefined reference to `pthread_join'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1992: undefined reference to `pthread_join'
 /tmp/ccrlR3MW.o: In function `tsync_start_sibling':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
 /tmp/ccrlR3MW.o: In function `TSYNC_two_siblings_with_ancestor':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2016: undefined reference to `sem_wait'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2032: undefined reference to `pthread_join'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2034: undefined reference to `pthread_join'
 /tmp/ccrlR3MW.o: In function `tsync_start_sibling':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
 /tmp/ccrlR3MW.o: In function `TSYNC_two_sibling_want_nnp':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2046: undefined reference to `sem_wait'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2058: undefined reference to `pthread_join'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2060: undefined reference to `pthread_join'
 /tmp/ccrlR3MW.o: In function `tsync_start_sibling':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
 /tmp/ccrlR3MW.o: In function `TSYNC_two_siblings_with_no_filter':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2073: undefined reference to `sem_wait'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2098: undefined reference to `pthread_join'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2100: undefined reference to `pthread_join'
 /tmp/ccrlR3MW.o: In function `tsync_start_sibling':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
 /tmp/ccrlR3MW.o: In function `TSYNC_two_siblings_with_one_divergence':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2125: undefined reference to `sem_wait'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2143: undefined reference to `pthread_join'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2145: undefined reference to `pthread_join'
 /tmp/ccrlR3MW.o: In function `tsync_start_sibling':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
 /tmp/ccrlR3MW.o: In function `TSYNC_two_siblings_not_under_filter':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2169: undefined reference to `sem_wait'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2202: undefined reference to `pthread_join'
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2227: undefined reference to `pthread_join'
 /tmp/ccrlR3MW.o: In function `tsync_start_sibling':
 /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'

It's GNU Make and linker specific.

The default Makefile rule looks like:

$(CC) $(CFLAGS) $(LDFLAGS) $@ $^ $(LDLIBS)

When linking is done by gcc itself, no issue, but when it needs to be passed
to proper ld, only LDLIBS follows and then ld cannot know what libs to link
with.

More detail:
https://www.gnu.org/software/make/manual/html_node/Implicit-Variables.html

LDFLAGS
Extra flags to give to compilers when they are supposed to invoke the linker,
‘ld’, such as -L. Libraries (-lfoo) should be added to the LDLIBS variable
instead.

LDLIBS
Library flags or names given to compilers when they are supposed to invoke the
linker, ‘ld’. LOADLIBES is a deprecated (but still supported) alternative to
LDLIBS. Non-library linker flags, such as -L, should go in the LDFLAGS
variable.

https://lkml.org/lkml/2010/2/10/362

tools/perf: libraries must come after objects

Link order matters, use LDLIBS instead of LDFLAGS to properly link against
libpthread.
Signed-off-by: Fathi Boudra <fathi.boudra@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 827cb032 ]

I submitted this driver several times before it got accepted. The
first series hasn't been accepted but the DTS binding did made it.
I then made a second series that added generic reset support to the
PHY core, this in turn required a change to the DT binding. This
second series seemed to have been ignored, so I did a third one
without the change to the PHY core and the DT binding update, and this
last attempt finally made it.

But two months later the DT binding update from the second series has
been integrated too. So now the driver doesn't match the binding and
the only DTS using it. This patch fix the driver to match the new
binding.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 00980815 ]

In the power on function the error path doesn't return the suspend
override to its proper state. It should should deassert this reset
line to enable the suspend override.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 91cd63d3 ]

An expansion field was added to the kernel copy of this structure for
future use. See mm/gup_benchmark.c.

Add the same expansion field here, so that the IOCTL command decodes
correctly. Otherwise, it fails with EINVAL.
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c407cd00 ]

Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.

1) Uses of size += snprintf(buf, SIZE - size, fmt, ...)
In this case, if snprintf would have written more characters than what the
buffer size (SIZE) is, then size will end up larger than SIZE. In later
uses of snprintf, SIZE - size will result in a negative number, leading
to problems. Note that size might already be too large by using
size = snprintf before the code reaches a case of size += snprintf.

2) If size is ultimately used as a length parameter for a copy back to user
space, then it will potentially allow for a buffer overflow and information
disclosure when size is greater than SIZE. When the size is used to index
the buffer directly, we can have memory corruption. This also means when
size = snprintf... is used, it may also cause problems since size may become
large.  Copying to userspace is mitigated by the HARDENED_USERCOPY kernel
configuration.

The solution to these issues is to use scnprintf which returns the number of
characters actually written to the buffer, so the size variable will never
exceed SIZE.
Signed-off-by: Silvio Cesare <silvio.cesare@gmail.com>
Cc: Timur Tabi <timur@kernel.org>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Xiubo Li <Xiubo.Lee@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e581e151 ]

Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.

1) Uses of size += snprintf(buf, SIZE - size, fmt, ...)
In this case, if snprintf would have written more characters than what the
buffer size (SIZE) is, then size will end up larger than SIZE. In later
uses of snprintf, SIZE - size will result in a negative number, leading
to problems. Note that size might already be too large by using
size = snprintf before the code reaches a case of size += snprintf.

2) If size is ultimately used as a length parameter for a copy back to user
space, then it will potentially allow for a buffer overflow and information
disclosure when size is greater than SIZE. When the size is used to index
the buffer directly, we can have memory corruption. This also means when
size = snprintf... is used, it may also cause problems since size may become
large.  Copying to userspace is mitigated by the HARDENED_USERCOPY kernel
configuration.

The solution to these issues is to use scnprintf which returns the number of
characters actually written to the buffer, so the size variable will never
exceed SIZE.
Signed-off-by: Silvio Cesare <silvio.cesare@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ee7ea2a9 ]

Fix typo which causes headphone no sound while using BCLK
as PLL source.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bf7d28c5 ]

Using sizeof(pointer) for determining the size of a memset() only works
when the size of the pointer and the size of type to which it points are
the same. For pte_t this is only true for 64bit and 32bit-NONPAE. On 32bit
PAE systems this is wrong as the pointer size is 4 byte but the PTE entry
is 8 bytes. It's actually not a real world issue as this code depends on
64bit, but it's wrong nevertheless.

Use sizeof(*p) for correctness sake.

Fixes: aad98391 ("x86/mm/encrypt: Simplify sme_populate_pgd() and sme_populate_pgd_large()")
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: dave.hansen@linux.intel.com
Cc: peterz@infradead.org
Cc: luto@kernel.org
Link: https://lkml.kernel.org/r/1546065252-97996-1-git-send-email-peng.hao2@zte.com.cnSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bddda606 ]

If all CPUs in the irq_default_affinity mask are offline when an interrupt
is initialized then irq_setup_affinity() can set an empty affinity mask for
a newly allocated interrupt.

Fix this by falling back to cpu_online_mask in case the resulting affinity
mask is zero.
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-msm@vger.kernel.org
Link: https://lkml.kernel.org/r/1545312957-8504-1-git-send-email-sramana@codeaurora.orgSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7b302772 ]

Unfortunately, some RTC don't have a second resolution for alarm so also
test for alarm on a minute boundary.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit fdac9448 ]

Return values for select are not checked properly and timeouts may not be
detected.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit df28169e ]

The source_sink_alloc_func() function is supposed to return error
pointers on error.  The function is called from usb_get_function() which
doesn't check for NULL returns so it would result in an Oops.

Of course, in the current kernel, small allocations always succeed so
this doesn't affect runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 88b1bb1f ]

Currently the link_state is uninitialized and the default value is 0(U0)
before the first time we start the udc, and after we start the udc then
 stop the udc, the link_state will be undefined.
We may have the following warnings if we start the udc again with
an undefined link_state:

WARNING: CPU: 0 PID: 327 at drivers/usb/dwc3/gadget.c:294 dwc3_send_gadget_ep_cmd+0x304/0x308
dwc3 100e0000.hidwc3_0: wakeup failed --> -22
[...]
Call Trace:
[<c010f270>] (unwind_backtrace) from [<c010b3d8>] (show_stack+0x10/0x14)
[<c010b3d8>] (show_stack) from [<c034a4dc>] (dump_stack+0x84/0x98)
[<c034a4dc>] (dump_stack) from [<c0118000>] (__warn+0xe8/0x100)
[<c0118000>] (__warn) from [<c0118050>](warn_slowpath_fmt+0x38/0x48)
[<c0118050>] (warn_slowpath_fmt) from [<c0442ec0>](dwc3_send_gadget_ep_cmd+0x304/0x308)
[<c0442ec0>] (dwc3_send_gadget_ep_cmd) from [<c0445e68>](dwc3_ep0_start_trans+0x48/0xf4)
[<c0445e68>] (dwc3_ep0_start_trans) from [<c0446750>](dwc3_ep0_out_start+0x64/0x80)
[<c0446750>] (dwc3_ep0_out_start) from [<c04451c0>](__dwc3_gadget_start+0x1e0/0x278)
[<c04451c0>] (__dwc3_gadget_start) from [<c04452e0>](dwc3_gadget_start+0x88/0x10c)
[<c04452e0>] (dwc3_gadget_start) from [<c045ee54>](udc_bind_to_driver+0x88/0xbc)
[<c045ee54>] (udc_bind_to_driver) from [<c045f29c>](usb_gadget_probe_driver+0xf8/0x140)
[<c045f29c>] (usb_gadget_probe_driver) from [<bf005424>](gadget_dev_desc_UDC_store+0xac/0xc4 [libcomposite])
[<bf005424>] (gadget_dev_desc_UDC_store [libcomposite]) from[<c023d8e0>] (configfs_write_file+0xd4/0x160)
[<c023d8e0>] (configfs_write_file) from [<c01d51e8>] (__vfs_write+0x1c/0x114)
[<c01d51e8>] (__vfs_write) from [<c01d5ff4>] (vfs_write+0xa4/0x168)
[<c01d5ff4>] (vfs_write) from [<c01d6d40>] (SyS_write+0x3c/0x90)
[<c01d6d40>] (SyS_write) from [<c0107400>] (ret_fast_syscall+0x0/0x3c)
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 01c10880 ]

We see dwc3 endpoint stopped by unwanted irq during
suspend resume test, which is caused dwc3 ep can't be started
with error "No Resource".

Here, add synchronize_irq before suspend to sync the
pending IRQ handlers complete.
Signed-off-by: Bo He <bo.he@intel.com>
Signed-off-by: Yu Wang <yu.y.wang@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 3fe931b3 ]

The intel_soc_dts_iosf_init() function doesn't return NULL, it returns
error pointers.

Fixes: 4d0dd6c1 ("Thermal/int340x/processor_thermal: Enable auxiliary DTS for Braswell")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2137a109 ]

In case the upstream clock are not set, which can happen in case the
VC5 has no valid upstream clock, the $src variable is used uninited
by regmap_update_bits(). Check for this condition and return -EINVAL
in such case.

Note that in case the VC5 has no valid upstream clock, the VC5 can
not operate correctly. That is a hardware property of the VC5. The
internal oscilator present in some VC5 models is also considered
upstream clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-renesas-soc@vger.kernel.org
[sboyd@kernel.org: Added comment about probe preventing this from
happening in the first place]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c6e90997 ]

Add a missing comma so that the output is valid JSON format again.

Fixes: 9fba738a ("clk: add duty cycle support")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d39eca54 ]

If tegra_dfll_unregister() fails then "soc" is an error pointer.  We
should just return instead of dereferencing it.

Fixes: 1752c9ee ("clk: tegra: dfll: Fix drvdata overwriting issue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8c3590de ]

Inside function rt274_i2c_probe(), if regmap_read() function
returns -EINVAL, then local variable "val" leaves uninitialized
but used in if statement. This is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 678e2b44 ]

The problem is seen in the q6asm_dai_compr_set_params() function:

	ret = q6asm_map_memory_regions(dir, prtd->audio_client, prtd->phys,
				       (prtd->pcm_size / prtd->periods),
                                        ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
				       prtd->periods);

In this code prtd->pcm_size is the buffer_size and prtd->periods comes
from params->buffer.fragments.  If we allow the number of fragments to
be zero then it results in a divide by zero bug.  One possible fix would
be to use prtd->pcm_count directly instead of using the division to
re-calculate it.  But I decided that it doesn't really make sense to
allow zero fragments.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 906a9abc ]

For some reason this field was set to zero when all other drivers use
.dynamic = 1 for front-ends. This change was tested on Dell XPS13 and
has no impact with the existing legacy driver. The SOF driver also works
with this change which enables it to override the fixed topology.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 99c66bc0 ]

Prevents deadlock when fifo is full and reader closes file.
Signed-off-by: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

commit ffeafdd2 upstream.

The sysfs phy_identifier attribute for a sas_end_device comes from the rphy
phy_identifier value.

Currently this is not being set for rphys with an end device attached, so
we see incorrect symlinks from systemd disk/by-path:

root@localhost:~# ls -l /dev/disk/by-path/
total 0
lrwxrwxrwx 1 root root  9 Feb 13 12:26 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy0-lun-0 -> ../../sdb
lrwxrwxrwx 1 root root 10 Feb 13 12:26 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy0-lun-0-part1 -> ../../sdb1
lrwxrwxrwx 1 root root 10 Feb 13 12:26 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy0-lun-0-part2 -> ../../sdb2
lrwxrwxrwx 1 root root 10 Feb 13 12:26 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy0-lun-0-part3 -> ../../sdc3

Indeed, each sas_end_device phy_identifier value is 0:

root@localhost:/# more sys/class/sas_device/end_device-0\:0\:2/phy_identifier
0
root@localhost:/# more sys/class/sas_device/end_device-0\:0\:10/phy_identifier
0

This patch fixes the discovery code to set the phy_identifier.  With this,
we now get proper symlinks:

root@localhost:~# ls -l /dev/disk/by-path/
total 0
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy10-lun-0 -> ../../sdg
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy11-lun-0 -> ../../sdh
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy2-lun-0 -> ../../sda
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy2-lun-0-part1 -> ../../sda1
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy3-lun-0 -> ../../sdb
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy3-lun-0-part1 -> ../../sdb1
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy3-lun-0-part2 -> ../../sdb2
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy4-lun-0 -> ../../sdc
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy4-lun-0-part1 -> ../../sdc1
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy4-lun-0-part2 -> ../../sdc2
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy4-lun-0-part3 -> ../../sdc3
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy5-lun-0 -> ../../sdd
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy7-lun-0 -> ../../sde
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy7-lun-0-part1 -> ../../sde1
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy7-lun-0-part2 -> ../../sde2
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy7-lun-0-part3 -> ../../sde3
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy8-lun-0 -> ../../sdf
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy8-lun-0-part1 -> ../../sdf1
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy8-lun-0-part2 -> ../../sdf2
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy8-lun-0-part3 -> ../../sdf3

Fixes: 2908d778 ("[SCSI] aic94xx: new driver")
Reported-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5c14a4d0 upstream.

When we did the original tests for the optimal value of sk_pacing_shift, we
came up with 6 ms of buffering as the default. Sadly, 6 is not a power of
two, so when picking the shift value I erred on the size of less buffering
and picked 4 ms instead of 8. This was probably wrong; those 2 ms of extra
buffering makes a larger difference than I thought.

So, change the default pacing shift to 7, which corresponds to 8 ms of
buffering. The point of diminishing returns really kicks in after 8 ms, and
so having this as a default should cut down on the need for extensive
per-device testing and overrides needed in the drivers.

Cc: stable@vger.kernel.org
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit e8da8794 ]

On large systems with multiple devices of the same class (e.g. NVMe disks,
using managed interrupts), the kernel can affinitize these interrupts to a
small subset of CPUs instead of spreading them out evenly.

irq_matrix_alloc_managed() tries to select the CPU in the supplied cpumask
of possible target CPUs which has the lowest number of interrupt vectors
allocated.

This is done by searching the CPU with the highest number of available
vectors. While this is correct for non-managed CPUs it can select the wrong
CPU for managed interrupts. Under certain constellations this results in
affinitizing the managed interrupts of several devices to a single CPU in
a set.

The book keeping of available vectors works the following way:

 1) Non-managed interrupts:

    available is decremented when the interrupt is actually requested by
    the device driver and a vector is assigned. It's incremented when the
    interrupt and the vector are freed.

 2) Managed interrupts:

    Managed interrupts guarantee vector reservation when the MSI/MSI-X
    functionality of a device is enabled, which is achieved by reserving
    vectors in the bitmaps of the possible target CPUs. This reservation
    decrements the available count on each possible target CPU.

    When the interrupt is requested by the device driver then a vector is
    allocated from the reserved region. The operation is reversed when the
    interrupt is freed by the device driver. Neither of these operations
    affect the available count.

    The reservation persist up to the point where the MSI/MSI-X
    functionality is disabled and only this operation increments the
    available count again.

For non-managed interrupts the available count is the correct selection
criterion because the guaranteed reservations need to be taken into
account. Using the allocated counter could lead to a failing allocation in
the following situation (total vector space of 10 assumed):

		 CPU0	CPU1
 available:	    2	   0
 allocated:	    5	   3   <--- CPU1 is selected, but available space = 0
 managed reserved:  3	   7

 while available yields the correct result.

For managed interrupts the available count is not the appropriate
selection criterion because as explained above the available count is not
affected by the actual vector allocation.

The following example illustrates that. Total vector space of 10
assumed. The starting point is:

		 CPU0	CPU1
 available:	    5	   4
 allocated:	    2	   3
 managed reserved:  3	   3

 Allocating vectors for three non-managed interrupts will result in
 affinitizing the first two to CPU0 and the third one to CPU1 because the
 available count is adjusted with each allocation:

		  CPU0	CPU1
 available:	     5	   4	<- Select CPU0 for 1st allocation
 --> allocated:	     3	   3

 available:	     4	   4	<- Select CPU0 for 2nd allocation
 --> allocated:	     4	   3

 available:	     3	   4	<- Select CPU1 for 3rd allocation
 --> allocated:	     4	   4

 But the allocation of three managed interrupts starting from the same
 point will affinitize all of them to CPU0 because the available count is
 not affected by the allocation (see above). So the end result is:

		  CPU0	CPU1
 available:	     5	   4
 allocated:	     5	   3

Introduce a "managed_allocated" field in struct cpumap to track the vector
allocation for managed interrupts separately. Use this information to
select the target CPU when a vector is allocated for a managed interrupt,
which results in more evenly distributed vector assignments. The above
example results in the following allocations:

		 CPU0	CPU1
 managed_allocated: 0	   0	<- Select CPU0 for 1st allocation
 --> allocated:	    3	   3

 managed_allocated: 1	   0	<- Select CPU1 for 2nd allocation
 --> allocated:	    3	   4

 managed_allocated: 1	   1	<- Select CPU0 for 3rd allocation
 --> allocated:	    4	   4

The allocation of non-managed interrupts is not affected by this change and
is still evaluating the available count.

The overall distribution of interrupt vectors for both types of interrupts
might still not be perfectly even depending on the number of non-managed
and managed interrupts in a system, but due to the reservation guarantee
for managed interrupts this cannot be avoided.

Expose the new field in debugfs as well.

[ tglx: Clarified the background of the problem in the changelog and
  	described it independent of NVME ]
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Michael Kelley <mikelley@microsoft.com>
Link: https://lkml.kernel.org/r/20181106040000.27316-1-longli@linuxonhyperv.comSigned-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 76f99ae5 ]

Linux spreads out the non managed interrupt across the possible target CPUs
to avoid vector space exhaustion.

Managed interrupts are treated differently, as for them the vectors are
reserved (with guarantee) when the interrupt descriptors are initialized.

When the interrupt is requested a real vector is assigned. The assignment
logic uses the first CPU in the affinity mask for assignment. If the
interrupt has more than one CPU in the affinity mask, which happens when a
multi queue device has less queues than CPUs, then doing the same search as
for non managed interrupts makes sense as it puts the interrupt on the
least interrupt plagued CPU. For single CPU affine vectors that's obviously
a NOOP.

Restructre the matrix allocation code so it does the 'best CPU' search, add
the sanity check for an empty affinity mask and adapt the call site in the
x86 vector management code.

[ tglx: Added the empty mask check to the core and improved change log ]
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/20180908175838.14450-2-dou_liyang@163.comSigned-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 8ffe4e61 ]

Linux finds the CPU which has the lowest vector allocation count to spread
out the non managed interrupts across the possible target CPUs, but does
not do so for managed interrupts.

Split out the CPU selection code into a helper function for reuse. No
functional change.
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/20180908175838.14450-1-dou_liyang@163.comSigned-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 87454b6e upstream.

During testing on Armada 388 platforms, it was found with a certain
module configuration that it was possible to trigger a kernel oops
during the module load process, caused by the phylink resolver being
triggered for a currently disabled interface.

This problem was introduced by changing the way the SFP registration
works, which now can result in the sfp link down notification being
called during phylink_create().

Fixes: b5bfc21a ("net: sfp: do not probe SFP module before we're attached")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1f60652d upstream.

Clang warns when one enumerated type is implicitly converted to another:

drivers/pinctrl/pinctrl-max77620.c:56:12: warning: implicit conversion
from enumeration type 'enum max77620_pinconf_param' to different
enumeration type 'enum pin_config_param' [-Wenum-conversion]
                .param = MAX77620_ACTIVE_FPS_SOURCE,
                         ^~~~~~~~~~~~~~~~~~~~~~~~~~

It is expected that pinctrl drivers can extend pin_config_param because
of the gap between PIN_CONFIG_END and PIN_CONFIG_MAX so this conversion
isn't an issue. Most drivers that take advantage of this define the
PIN_CONFIG variables as constants, rather than enumerated values. Do the
same thing here so that Clang no longer warns.

Link: https://github.com/ClangBuiltLinux/linux/issues/139Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 68a958a9 upstream.

The udlfb driver maintained an open count and cleaned up itself when the
count reached zero. But the console is also counted in the reference count
- so, if the user unplugged the device, the open count would not drop to
zero and the driver stayed loaded with console attached. If the user
re-plugged the adapter, it would create a device /dev/fb1, show green
screen and the access to the console would be lost.

The framebuffer subsystem has reference counting on its own - in order to
fix the unplug bug, we rely the framebuffer reference counting. When the
user unplugs the adapter, we call unregister_framebuffer unconditionally.
unregister_framebuffer will unbind the console, wait until all users stop
using the framebuffer and then call the fb_destroy method. The fb_destroy
cleans up the USB driver.

This patch makes the following changes:
* Drop dlfb->kref and rely on implicit framebuffer reference counting
  instead.
* dlfb_usb_disconnect calls unregister_framebuffer, the rest of driver
  cleanup is done in the function dlfb_ops_destroy. dlfb_ops_destroy will
  be called by the framebuffer subsystem when no processes have the
  framebuffer open or mapped.
* We don't use workqueue during initialization, but initialize directly
  from dlfb_usb_probe. The workqueue could race with dlfb_usb_disconnect
  and this racing would produce various kinds of memory corruption.
* We use usb_get_dev and usb_put_dev to make sure that the USB subsystem
  doesn't free the device under us.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
cc: Dave Airlie <airlied@redhat.com>
Cc: Bernie Thompson <bernie@plugable.com>,
Cc: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>