In DQA mode, there is no need to wait for the TXQ to
clear out after getting a DELBA, since traffic can
continue running on the queue.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

ath.git patches for 4.13. Major changes:

wil6210

* add low level RF sector interface via nl80211 vendor commands

* add module parameter ftm_mode to load separate firmware for factory
  testing

* support devices with different PCIe bar size

* add support for PCIe D3hot in system suspend

* remove ioctl interface which should not be in a wireless driver

ath10k

* go back to using dma_alloc_coherent() for firmware scratch memory

* add per chain RSSI reporting

This fixes spin-forever in irq handler when IRQ is already asserted
at request_irq() time.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

To yield better user experience, have btcoex control LPS's parameters.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If LPS is controlled by btcoex, this function tell driver LPS is on or off.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If RX ampdu is too long, BT will have less time.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add btcoex record pwr mode to control LPS's parameters and share time
with BT.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We extend types of special packets to a enumeration from boolean value.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When using EAPOL to do a PTK rekey, there is a possible race condition.
When msg 3/4 is received, the supplicant will send msg 4/4 and install
the new key immediately; however, the driver must make sure that msg 4/4
is sent before installing the new key. We use TX report to ensure it is
sent.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The number of debugging conditions now exceeds the capabilities of a
32-bit word.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Since the driver itself will enter power saving mode dynamically
according to the traffic, we set hw capability SUPPORTS_PS and
SUPPORTS_DYNAMIC_PS in case of fwctrl_lps.

The process IEEE80211_CONF_CHANGE_PS in op_config is used by
SW-LPS only, so we add constraints to avoid errors.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: vincent_fann <vincent_fann@realtek.com>
Signed-off-by: shaofu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

To make ant_sel work, we should call power_on_setting to set antenna
correctly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This commit fixies two problems. The first one is interface types
(e.g. PCI) that are used to switch antenna, and the second is to add
wifi_only parameter to give correct state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

New btcoex add a function 'bind' to connect adapter, so we should call
it during initializing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

After successful loading of firmware, a CARD READY indication is
received by host. Common device configuration parameters are sent
to the device after this. It includes information like device
operating mode (Wi-Fi alone or BT coex), power save related
parameters, GPIO information etc. As device supports BT coex,
this frame is send in COEX queue initially. Based on the operating
mode, CARD READY indication is received from each protocol module
in firmware i.e. WLAN, BT.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Boot parameters are changed in new firmware. Also three
new sdio sleep parameters are added for ultra low power
save.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

RS9113 chipset supports Coex feature. Initial frame exchanges during
device initialization happens on coex queue. This patch adds the
handling for coex queue.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Before firmware load, sometimes false interrupts are received.
System hang is observed if interrupt handler is not registered
to receive these interrupts. Hence interrupt handler registration
is moved before firmware load. We will drop these false interrupts
as these are not from the device.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Currently macros are used for FSM states. We will replace
it with enum so that new state can be added easily without
worrying about macro value.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

usb device id and vendor id for RS9113 chipset are included.
So it can be used through usb interface.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

debugfs_remove already check mwifiex_dfs_dir, so remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch uses WARN level is not printed by default.

In some cases, some boards have always met the unused log be printed as
follows.
...
[23193.523182] mwifiex_pcie 0000:01:00.0: mwifiex_get_cfp:
cannot find cfp by band 2    & channel=13 freq=0
[23378.633684] mwifiex_pcie 0000:01:00.0: mwifiex_get_cfp:
cannot find cfp by band 2    & channel=13 freq=0

Due to we used the wifi default area was US and didn't support 12~14
channels. As Frequencies:
* 2412 MHz [1] (30.0 dBm)
* 2417 MHz [2] (30.0 dBm)
* 2422 MHz [3] (30.0 dBm)
* 2427 MHz [4] (30.0 dBm)
* 2432 MHz [5] (30.0 dBm)
* 2437 MHz [6] (30.0 dBm)
* 2442 MHz [7] (30.0 dBm)
* 2447 MHz [8] (30.0 dBm)
* 2452 MHz [9] (30.0 dBm)
* 2457 MHz [10] (30.0 dBm)
* 2462 MHz [11] (30.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)

Also, as the commit 1b499cb7
("mwifiex: disable channel filtering feature in firmware"), it proved to
be a feature to get better scan result from overlapping channel.

Even there could be AP from overlapping channel (might be 12/13/14
in this case), it will be filtered depend on reg domain rules.
e.g:
...
if (ch->flags & IEEE80211_CHAN_DISABLED)
        continue;

So it should not been an ERROR, use the WARN level to instead it for now.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The REG_USTIME_TSF (US Time Tuning for TSF) definition of Realtek chips
should be 0x55C.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The brcm43430 chip needs different firmware files for chip revision 0
and 1. The file currently in linux-firmware is for revision 1 only.

This commit makes brcmfmac request brcmfmac43430a0-sdio.bin instead
of brcmfmac43430-sdio.bin for revision 0 chips.

Note that the behavior for revision 1 chips is not changed, ideally those
would load brcmfmac43430a1-sdio.bin, but that will break existing setups.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Wireless drivers should not be using ioctl interface,
hence remove this interface for wil6210 driver.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In order to preserve the connection in suspend/resume flow,
wil6210 host allows going to PCIe D3hot state in suspend,
instead of performing a full wil6210 device reset. This
requires the platform ability to initiate wakeup in case of
RX data. To check that, a new platform API is added.
In addition, add cfg80211 suspend/resume callbacks
implementation.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

After calling platform_ops.uninit() it is still possible to invoke
platform callbacks.
To prevent this, zero platform_ops right after invoking uninit.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

QCA9888 supports VHT80 with 2x2. But it only support 1x1 with VHT160 or
VHT80+80. Inform userspace and the the QCA firmware about that limitation
whenever VHT80+80 or VHT160 is configured.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

QCA9984 hardware can do 4x4 at 80Mhz, but only 2x2 at 160Mhz.

First, report this to user-space by setting the max-tx-speed
and max-rx-speed vht capabilities.

Second, if the peer rx-speed is configured, and if we
are in 160 or 80+80 mode, and the peer rx-speed matches
the max speed for 2x2 or 1x1 at 160Mhz (long guard interval),
then use that info to set the peer_bw_rxnss_override appropriately.

Without this, a 9984 firmware will not use 2x2 ratesets when
transmitting to peer (it will be stuck at 1x1), because
the firmware would not have configured the rxnss_override.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: rebase, cleanup, drop 160Mhz workaround cleanup]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params, rename the title]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The ath10k firmware doesn't announce its VHT channel width capabilities in
the vht_cap information from the "service ready event" arguments. The
driver must therefore check whether the 160MHz short GI bit is set and
whether the driver still doesn't set the bits for the 160/80+80 MHz
capabilities.

The two bits for the channel width are a two bit integer and not two
separate bits which cannot be parsed without the knowledge of the other
bit. Using IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ (b10..) as a
mask for this task doesn't make any sense. The correct mask for the VHT
channel width should be used instead to make this check more readable.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: separate 160Mhz workaround cleanup, add commit
 message]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Trivial fix to spelling mistake in ath6kl_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Steve deRosier <derosier@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Report per chain RSSI to mac80211.
Signed-off-by: Norik Dzhandzhapanyan <norikd@gmail.com>
[kvalo@qca.qualcomm.com: fix conflicts and style]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Define structures for the copy engine ctrl/misc registers,
that includes CE CMD halt, watermark source, watermark destination,
host IE ring, source, destination and dmax ring.

This adds support to avoid the conditional compilation,
code optimization and dynamic configuration of the copy engine
register map for respective hardware bus interface.
Signed-off-by: Sarada Prasanna Garnayak <c_sgarna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Remove unnecessary variable and refactor the code.

Addresses-Coverity-ID: 1365000
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Motorola Droid 4 uses a WL 1285C. With differences between
chips not being public let's add explicit binding for wl1285
instead of relying on wl1283 being very similar.
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The semaphore 'async_sem' is used as a simple mutex, so
it should be written as one. Semaphores are going away in the future.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Instead of rssi status, the btcoex also needs to get the link status of
the wifi. In addition, some of the rssi status can be merged into link
status.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

These display functions are useless and will not be called in the
future.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When initializing, gather BT information in struct btcoexist and
provide them to wifi driver.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Hook the external functions for newer ICs such as 8821a and 8192e.

Rename ex_halbtc8192e2ant_halt_notify to ex_btc8192e2ant_halt_notify.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>