Distinguish between rx_drops and xdp_drops since the latter is already
reported in rx_packets. Report xdp_drops in ethtool statistics
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce xdp_tx, xdp_redirect and rx_drops counters in veth_stats data
structure. Move stats accounting in veth_poll. Remove xdp_xmit variable
in veth_xdp_rcv_one/veth_xdp_rcv_skb and rely on veth_stats counters.
This is a preliminary patch to align veth xdp statistics to mlx, intel
and marvell xdp implementation
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move xdp stats in veth_stats data structure. This is a preliminary patch
to align xdp statistics to mlx5, ixgbe and mvneta drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The CONFIG_SYSFS declaration of sysfs_group_change_owner() is different
from the !CONFIG_SYSFS version and thus causes build failurs when
!CONFIG_SYSFS is set.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 303a4276 ("sysfs: add sysfs_group{s}_change_owner()")
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
net: phy: mscc: add support for RGMII MAC mode

This series adds support for the RGMII MAC mode for the VSC8584 PHY
family and for RGMII_ID modes (Tx and/or Rx).

I decided to drop the custom delay for now. I made some tests and it
seemed to be working quite well. If we find out we really need to lower
the delay, which I doubt, I'll send support for it.

Since v2:
  - Dropped support for custom dt bindings.
  - Add the 2ns delay based on the interface mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for configuring the RGMII skew delays in Rx and
Tx. The Rx and Tx skews are set based on the interface mode. By default
their configuration is set to the default value in hardware (0.2ns);
this means the driver do not rely anymore on the bootloader
configuration.

Then based on the interface mode being used, a 2ns delay is added:
- RGMII_ID adds it for both Rx and Tx.
- RGMII_RXID adds it for Rx.
- RGMII_TXID adds it for Tx.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for connecting VSC8584 PHYs to the MAC using
RGMII.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Offload TC action skbedit priority

Petr says:

The TC action "skbedit priority P" has the effect of assigning skbprio of P
to SKBs that it's applied on. In HW datapath of a switch, the corresponding
action is assignment of internal switch priority. Spectrum switches allow
setting of packet priority based on an ACL action, which is good match for
the skbedit priority gadget. This patchset therefore implements offloading
of this action to the Spectrum ACL engine.

After a bit of refactoring in patch #1, patch #2 extends the skbedit action
to support offloading of "priority" subcommand.

On mlxsw side, in patch #3, the QOS_ACTION flexible action is added, with
fields necessary for priority adjustment. In patch #4, "skbedit priority"
is connected to that action.

Patch #5 implements a new forwarding selftest, suitable for both SW- and
HW-datapath testing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test that runs traffic through a port such that skbedit priority
action acts on it during forwarding. Test that at egress, it is classified
correctly according to the new priority at a PRIO qdisc.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Offload action skbedit priority when keyed to a flower classifier. The
skb->priority field in Linux is very generic, so only allow setting the
bottom 8 priorities and bounce anything else.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The QOS_ACTION is used for manipulating the QoS attributes of a packet.
Add the corresponding defines and helpers, in particular for the
switch_priority override.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skbedit action "priority" is used for adjusting SKB priority. Allow
drivers to offload the action by introducing two new skbedit getters and a
new flow action, and initializing appropriately in tc_setup_flow_action().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The two functions is_tcf_skbedit_mark() and is_tcf_skbedit_ptype() have a
very similar structure. A follow-up patch will add one more such function.
Instead of more cut'n'pasting, extract a helper function that checks
whether a TC action is an skbedit with the required flag. Convert the two
existing functions into thin wrappers around the helper.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

it will check the return value of dwmac_dma_reset() in the
stmmac_init_dma_engine() function and report an error if the
return value is not zero. so don't need check here.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit a5afc167 ("net: phy: mscc: add support for VSC8584 PHY")
introduced a call to 'phy_write' storing its return value to a variable
called 'ret'. But 'ret' never was checked for a possible error being
returned, and hence was not used at all. Fix this by checking the return
value and exiting the function if an error was returned.

As this does not fix a known bug, this commit is mostly cosmetic and not
sent as a fix.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_chip_specific_setup':
drivers/net/ethernet/cavium/liquidio/lio_main.c:1378:8: warning:
 variable 's' set but not used [-Wunused-but-set-variable]

It's not used since commit b6334be6 ("net/liquidio: Delete driver version assignment")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The cited commit removed RTNL from tc_setup_flow_action(), but the
function calls two tunnel key action helpers that use rtnl_dereference()
to fetch the action's parameters. This leads to "suspicious RCU usage"
warnings [1][2].

Change the helpers to use rcu_dereference_protected() while requiring
the action's lock to be held. This is safe because the two helpers are
only called from tc_setup_flow_action() which acquires the lock.

[1]
[  156.950855] =============================
[  156.955463] WARNING: suspicious RCU usage
[  156.960085] 5.6.0-rc5-custom-47426-gdfe43878d573 #2409 Not tainted
[  156.967116] -----------------------------
[  156.971728] include/net/tc_act/tc_tunnel_key.h:31 suspicious rcu_dereference_protected() usage!
[  156.981583]
[  156.981583] other info that might help us debug this:
[  156.981583]
[  156.990675]
[  156.990675] rcu_scheduler_active = 2, debug_locks = 1
[  156.998205] 1 lock held by tc/877:
[  157.002187]  #0: ffff8881cbf7bea0 (&(&p->tcfa_lock)->rlock){+...}, at: tc_setup_flow_action+0xbe/0x4f78
[  157.012866]
[  157.012866] stack backtrace:
[  157.017886] CPU: 2 PID: 877 Comm: tc Not tainted 5.6.0-rc5-custom-47426-gdfe43878d573 #2409
[  157.027253] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016
[  157.037389] Call Trace:
[  157.040170]  dump_stack+0xfd/0x178
[  157.044034]  lockdep_rcu_suspicious+0x14a/0x153
[  157.049157]  tc_setup_flow_action+0x89f/0x4f78
[  157.054227]  fl_hw_replace_filter+0x375/0x640
[  157.064348]  fl_change+0x28ec/0x4f6b
[  157.088843]  tc_new_tfilter+0x15e2/0x2260
[  157.176801]  rtnetlink_rcv_msg+0x8d6/0xb60
[  157.190915]  netlink_rcv_skb+0x177/0x460
[  157.208884]  rtnetlink_rcv+0x21/0x30
[  157.212925]  netlink_unicast+0x5d0/0x7f0
[  157.227728]  netlink_sendmsg+0x981/0xe90
[  157.245416]  ____sys_sendmsg+0x76d/0x8f0
[  157.255348]  ___sys_sendmsg+0x10f/0x190
[  157.320308]  __sys_sendmsg+0x115/0x1f0
[  157.342553]  __x64_sys_sendmsg+0x7d/0xc0
[  157.346987]  do_syscall_64+0xc1/0x600
[  157.351142]  entry_SYSCALL_64_after_hwframe+0x49/0xbe

[2]
[  157.432346] =============================
[  157.436937] WARNING: suspicious RCU usage
[  157.441537] 5.6.0-rc5-custom-47426-gdfe43878d573 #2409 Not tainted
[  157.448559] -----------------------------
[  157.453204] include/net/tc_act/tc_tunnel_key.h:43 suspicious rcu_dereference_protected() usage!
[  157.463042]
[  157.463042] other info that might help us debug this:
[  157.463042]
[  157.472112]
[  157.472112] rcu_scheduler_active = 2, debug_locks = 1
[  157.479529] 1 lock held by tc/877:
[  157.483442]  #0: ffff8881cbf7bea0 (&(&p->tcfa_lock)->rlock){+...}, at: tc_setup_flow_action+0xbe/0x4f78
[  157.494119]
[  157.494119] stack backtrace:
[  157.499114] CPU: 2 PID: 877 Comm: tc Not tainted 5.6.0-rc5-custom-47426-gdfe43878d573 #2409
[  157.508485] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016
[  157.518628] Call Trace:
[  157.521416]  dump_stack+0xfd/0x178
[  157.525293]  lockdep_rcu_suspicious+0x14a/0x153
[  157.530425]  tc_setup_flow_action+0x993/0x4f78
[  157.535505]  fl_hw_replace_filter+0x375/0x640
[  157.545650]  fl_change+0x28ec/0x4f6b
[  157.570204]  tc_new_tfilter+0x15e2/0x2260
[  157.658199]  rtnetlink_rcv_msg+0x8d6/0xb60
[  157.672315]  netlink_rcv_skb+0x177/0x460
[  157.690278]  rtnetlink_rcv+0x21/0x30
[  157.694320]  netlink_unicast+0x5d0/0x7f0
[  157.709129]  netlink_sendmsg+0x981/0xe90
[  157.726813]  ____sys_sendmsg+0x76d/0x8f0
[  157.736725]  ___sys_sendmsg+0x10f/0x190
[  157.801721]  __sys_sendmsg+0x115/0x1f0
[  157.823967]  __x64_sys_sendmsg+0x7d/0xc0
[  157.828403]  do_syscall_64+0xc1/0x600
[  157.832558]  entry_SYSCALL_64_after_hwframe+0x49/0xbe

Fixes: b15e7a6e ("net: sched: don't take rtnl lock during flow_action setup")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for vlan stats to be included when dumping vlan
information. We have to dump them only when explicitly requested (thus the
flag below) because that disables the vlan range compression and will make
the dump significantly larger. In order to request the stats to be
included we add a new dump attribute called BRIDGE_VLANDB_DUMP_FLAGS which
can affect dumps with the following first flag:
  - BRIDGE_VLANDB_DUMPF_STATS
The stats are intentionally nested and put into separate attributes to make
it easier for extending later since we plan to add per-vlan mcast stats,
drop stats and possibly STP stats. This is the last missing piece from the
new vlan API which makes the dumped vlan information complete.

A dump request which should include stats looks like:
 [BRIDGE_VLANDB_DUMP_FLAGS] |= BRIDGE_VLANDB_DUMPF_STATS

A vlandb entry attribute with stats looks like:
 [BRIDGE_VLANDB_ENTRY] = {
     [BRIDGE_VLANDB_ENTRY_STATS] = {
         [BRIDGE_VLANDB_STATS_RX_BYTES]
         [BRIDGE_VLANDB_STATS_RX_PACKETS]
         ...
     }
 }
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The name is misleading, it actually tracks the 'fully established'
status.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2020-03-17

1) Compiler warnings and cleanup for the connection tracking series
2) Bug fixes for the connection tracking series
3) Fix devlink port register sequence
4) Last five patches in the series, By Eli cohen
   Add the support for forwarding traffic between two eswitch uplink
   representors (Hairpin for eswitch), using mlx5 termination tables
   to change the direction of a packet in hw from RX to TX pipeline.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

At least some integrated PHY's in RTL8168/RTL8125 chip versions support
downshift, and the actual link speed can be read from a vendor-specific
register. Info about this register was provided by Realtek.
More details about downshift configuration (e.g. number of attempts)
aren't available, therefore the downshift tunable is not implemented.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the commit referenced below, hw_stats_type of an entry is set for every
entry that corresponds to a pedit action. However, the assignment is only
done after the entry pointer is bumped, and therefore could overwrite
memory outside of the entries array.

The reason for this positioning may have been that the current entry's
hw_stats_type is already set above, before the action-type dispatch.
However, if there are no more actions, the assignment is wrong. And if
there are, the next round of the for_each_action loop will make the
assignment before the action-type dispatch anyway.

Therefore fix this issue by simply reordering the two lines.

Fixes: 74522e7b ("net: sched: set the hw_stats_type in pedit loop")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: spectrum_cnt: Expose counter resources

Jiri says:

Capacity and utilization of existing flow and RIF counters are currently
unavailable to be seen by the user. Use the existing devlink resources
API to expose the information:

$ sudo devlink resource show pci/0000:00:10.0 -v
pci/0000:00:10.0:
  name kvd resource_path /kvd size 524288 unit entry dpipe_tables none
  name span_agents resource_path /span_agents size 8 occ 0 unit entry dpipe_tables none
  name counters resource_path /counters size 79872 occ 44 unit entry dpipe_tables none
    resources:
      name flow resource_path /counters/flow size 61440 occ 4 unit entry dpipe_tables none
      name rif resource_path /counters/rif size 18432 occ 40 unit entry dpipe_tables none
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add tests for mlxsw hw_stats types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement occupancy counting for counters and expose over devlink
resource API.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Put all init operations related to subpools into
mlxsw_sp_counter_sub_pools_init().
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the validation of subpools configuration, to avoid possible over
commitment to resource registration. Add WARN_ON to indicate bug
in the code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement devlink resources support for counter pools. Move the subpool
sizes calculations into the new resources register function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new field to subpool struct that would indicate which
resource id should be used to query the entry size for
the subpool from the device.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the global static array of subpools is used. Make it
per-instance as multiple instances of the mlxsw driver can have
different values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the change that made the code to query counter bank size from device
instead of using hard-coded value, the number of available counters
changed for Spectrum-2. Adjust the limit in the selftests.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bank size is different between Spectrum versions. Also it is
a resource that can be queried. So instead of hard coding the value in
code, query it from the firmware.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Chelsio NICs have 3 filter regions, in following order of priority:
1. High Priority (HPFILTER) region (Highest Priority).
2. HASH region.
3. Normal FILTER region (Lowest Priority).

Currently, there's a 1-to-1 mapping between the prio value passed
by TC and the filter region index. However, it's possible to have
multiple TC rules with the same prio value. In this case, if a region
is exhausted, no attempt is made to try inserting the rule in the
next available region.

So, rework and remove the 1-to-1 mapping. Instead, dynamically select
the region to insert the filter rule, as long as the new rule's prio
value doesn't conflict with existing rules across all the 3 regions.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts the following commits:

  8537f786 ("netfilter: Introduce egress hook")
  5418d388 ("netfilter: Generalize ingress hook")
  b030f194 ("netfilter: Rename ingress hook include file")

>From the discussion in [0], the author's main motivation to add a hook
in fast path is for an out of tree kernel module, which is a red flag
to begin with. Other mentioned potential use cases like NAT{64,46}
is on future extensions w/o concrete code in the tree yet. Revert as
suggested [1] given the weak justification to add more hooks to critical
fast-path.

  [0] https://lore.kernel.org/netdev/cover.1583927267.git.lukas@wunner.de/
  [1] https://lore.kernel.org/netdev/20200318.011152.72770718915606186.davem@davemloft.net/Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Miller <davem@davemloft.net>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Nacked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2020-03-18

please apply the following patch series for qeth to netdev's net-next
tree.

This consists of three parts:
1) support for __GFP_MEMALLOC,
2) several ethtool enhancements (.set_channels, SW Timestamping),
3) the usual cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

To check whether a netdevice has already been registered, look at
NETREG_REGISTERED to replace some hacks I added a while ago.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth_do_ioctl() is only reached through our own net_device_ops, so we
can trust that dev->ml_priv still contains what we put there earlier.

qeth_bridgeport_an_set() is an internal function that doesn't require
such sanity checks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Data addresses in the AOB are absolute, and need to be translated before
being fed into kmem_cache_free(). Currently this phys_to_virt() is a no-op.
Also see commit 2db01da8 ("s390/qdio: fill SBALEs with absolute addresses").
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>