- 23 Jan, 2020 37 commits
-
-
Finn Thain authored
Section 5.5.3.2 of the datasheet says, If FIFO Underrun, Byte Count Mismatch, Excessive Collision, or Excessive Deferral (if enabled) errors occur, transmission ceases. In this situation, the chip asserts a TXER interrupt rather than TXDN. But the handler for the TXDN is the only way that the transmit queue gets restarted. Hence, an aborted transmission can result in a watchdog timeout. This problem can be reproduced on congested link, as that can result in excessive transmitter collisions. Another way to reproduce this is with a FIFO Underrun, which may be caused by DMA latency. In event of a TXER interrupt, prevent a watchdog timeout by restarting transmission. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Tested-by:Stan Johnson <userm57@yahoo.com> Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Finn Thain authored
Section 4.3.1 of the datasheet says, This bit [TXP] must not be set if a Load CAM operation is in progress (LCAM is set). The SONIC will lock up if both bits are set simultaneously. Testing has shown that the driver sometimes attempts to set LCAM while TXP is set. Avoid this by waiting for command completion before and after giving the LCAM command. After issuing the Load CAM command, poll for !SONIC_CR_LCAM rather than SONIC_INT_LCD, because the SONIC_CR_TXP bit can't be used until !SONIC_CR_LCAM. When in reset mode, take the opportunity to reset the CAM Enable register. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Tested-by: -
Finn Thain authored
There are several issues relating to command register usage during chip initialization. Firstly, the SONIC sometimes comes out of software reset with the Start Timer bit set. This gets logged as, macsonic macsonic eth0: sonic_init: status=24, i=101 Avoid this by giving the Stop Timer command earlier than later. Secondly, the loop that waits for the Read RRA command to complete has the break condition inverted. That's why the for loop iterates until its termination condition. Call the helper for this instead. Finally, give the Receiver Enable command after clearing interrupts, not before, to avoid the possibility of losing an interrupt. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Tested-by: -
Finn Thain authored
Make sure the SONIC's DMA engine is idle before altering the transmit and receive descriptors. Add a helper for this as it will be needed again. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Tested-by:
-
Finn Thain authored
As soon as the driver is finished with a receive buffer it allocs a new one and overwrites the corresponding RRA entry with a new buffer pointer. Problem is, the buffer pointer is split across two word-sized registers. It can't be updated in one atomic store. So this operation races with the chip while it stores received packets and advances its RRP register. This could result in memory corruption by a DMA write. Avoid this problem by adding buffers only at the location given by the RWP register, in accordance with the National Semiconductor datasheet. Re-factor this code into separate functions to calculate a RRA pointer and to update the RWP. Fixes: efcce839 ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by:
-
Finn Thain authored
After sonic_tx_timeout() calls sonic_init(), it can happen that sonic_rx() will subsequently encounter a receive descriptor with no flags set. Remove the comment that says that this can't happen. When giving a receive descriptor to the SONIC, clear the descriptor status field. That way, any rx descriptor with flags set can only be a newly received packet. Don't process a descriptor without the LPKT bit set. The buffer is still in use by the SONIC. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Tested-by:
-
Finn Thain authored
The while loop in sonic_rx() traverses the rx descriptor ring. It stops when it reaches a descriptor that the SONIC has not used. Each iteration advances the EOL flag so the SONIC can keep using more descriptors. Therefore, the while loop has no definite termination condition. The algorithm described in the National Semiconductor literature is quite different. It consumes descriptors up to the one with its EOL flag set (which will also have its "in use" flag set). All freed descriptors are then returned to the ring at once, by adjusting the EOL flags (and link pointers). Adopt the algorithm from datasheet as it's simpler, terminates quickly and avoids a lot of pointless descriptor EOL flag changes. Fixes: efcce839 ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by:
-
Finn Thain authored
The SONIC can sometimes advance its rx buffer pointer (RRP register) without advancing its rx descriptor pointer (CRDA register). As a result the index of the current rx descriptor may not equal that of the current rx buffer. The driver mistakenly assumes that they are always equal. This assumption leads to incorrect packet lengths and possible packet duplication. Avoid this by calling a new function to locate the buffer corresponding to a given descriptor. Fixes: efcce839 ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by:
-
Finn Thain authored
The tx_aborted_errors statistic should count packets flagged with EXD, EXC, FU, or BCM bits because those bits denote an aborted transmission. That corresponds to the bitmask 0x0446, not 0x0642. Use macros for these constants to avoid mistakes. Better to leave out FIFO Underruns (FU) as there's a separate counter for that purpose. Don't lump all these errors in with the general tx_errors counter as that's used for tx timeout events. On the rx side, don't count RDE and RBAE interrupts as dropped packets. These interrupts don't indicate a lost packet, just a lack of resources. When a lack of resources results in a lost packet, this gets reported in the rx_missed_errors counter (along with RFO events). Don't double-count rx_frame_errors and rx_crc_errors. Don't use the general rx_errors counter for events that already have special counters. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Tested-by:
-
Finn Thain authored
The driver accesses descriptor memory which is simultaneously accessed by the chip, so the compiler must not be allowed to re-order CPU accesses. sonic_buf_get() used 'volatile' to prevent that. sonic_buf_put() should have done so too but was overlooked. Fixes: efcce839 ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by:
-
Finn Thain authored
The chip can change a packet's descriptor status flags at any time. However, an active interrupt flag gets cleared rather late. This allows a race condition that could theoretically lose an interrupt. Fix this by clearing asserted interrupt flags immediately. Fixes: efcce839 ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by:
-
Finn Thain authored
The netif_stop_queue() call in sonic_send_packet() races with the netif_wake_queue() call in sonic_interrupt(). This causes issues like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out". Fix this by disabling interrupts when accessing tx_skb[] and next_tx. Update a comment to clarify the synchronization properties. Fixes: efcce839 ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by:
-
Madalin Bucur authored
As the only 10G PHY interface type defined at the moment the code was developed was XGMII, although the PHY interface mode used was not XGMII, XGMII was used in the code to denote 10G. This patch renames the 10G interface mode to remove the ambiguity. Signed-off-by:
Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by:
-
David S. Miller authored
Madalin Bucur says: ==================== net: fsl/fman: address erratum A011043 This addresses a HW erratum on some QorIQ DPAA devices. MDIO reads to internal PCS registers may result in having the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no error and read data (MDIO_DATA[MDIO_DATA]) is correct. Software may get false read error when reading internal PCS registers through MDIO. As a workaround, all internal MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit. When the issue was present, one could see such errors during boot: mdio_bus ffe4e5000: Error while reading PHY0 reg at 3.3 ==================== Signed-off-by: -
Madalin Bucur authored
When fsl,erratum-a011043 is set, adjust for erratum A011043: MDIO reads to internal PCS registers may result in having the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no error and read data (MDIO_DATA[MDIO_DATA]) is correct. Software may get false read error when reading internal PCS registers through MDIO. As a workaround, all internal MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit. Signed-off-by:
-
Madalin Bucur authored
Add fsl,erratum-a011043 to internal MDIO buses. Software may get false read error when reading internal PCS registers through MDIO. As a workaround, all internal MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit. Signed-off-by:
-
Madalin Bucur authored
Add an entry for erratum A011043: the MDIO_CFG[MDIO_RD_ER] bit may be falsely set when reading internal PCS registers. MDIO reads to internal PCS registers may result in having the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no error and read data (MDIO_DATA[MDIO_DATA]) is correct. Software may get false read error when reading internal PCS registers through MDIO. As a workaround, all internal MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit. Signed-off-by:
-
Manish Chopra authored
Driver while collecting firmware dump takes longer time to collect/process some of the firmware dump entries/memories. Bigger capture masks makes it worse as it results in larger amount of data being collected and results in CPU soft lockup. Place cond_resched() in some of the driver flows that are expectedly time consuming to relinquish the CPU to avoid CPU soft lockup panic. Signed-off-by:
Shahed Shaikh <shshaikh@marvell.com> Tested-by:
Yonggen Xu <Yonggen.Xu@dell.com> Signed-off-by:
Manish Chopra <manishc@marvell.com> Signed-off-by:
-
Kristian Evensen authored
When submitting v2 of "fou: Support binding FoU socket" (1713cb37), I accidentally sent the wrong version of the patch and one fix was missing. In the initial version of the patch, as well as the version 2 that I submitted, I incorrectly used ".type" for the two V6-attributes. The correct is to use ".len". Reported-by:
Dmitry Vyukov <dvyukov@google.com> Fixes: 1713cb37 ("fou: Support binding FoU socket") Signed-off-by:
Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-2020-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for v5.5 Second set of fixes for v5.5. There are quite a few patches, especially on iwlwifi, due to me being on a long break. Libertas also has a security fix and mt76 a build fix. iwlwifi * don't send the PPAG command when PPAG is disabled, since it can cause problems * a few fixes for a HW bug * a fix for RS offload; * a fix for 3168 devices where the NVM tables where the wrong tables were being read * fix a couple of potential memory leaks in TXQ code * disable L0S states in all hardware since our hardware doesn't officially support them anymore (and older versions of the hardware had instability in these states) * remove lar_disable parameter since it has been causing issues for some people who erroneously disable it * force the debug monitor HW to stop also when debug is disabled, since it sometimes stays on and prevents low system power states * don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems libertas * fix two buffer overflows mt76 * build fix related to CONFIG_MT76_LEDS * fix off by one in bitrates handling ==================== Signed-off-by:
-
Eric Dumazet authored
If both IFF_NAPI_FRAGS mode and XDP are enabled, and the XDP program consumes the skb, we need to clear the napi.skb (or risk a use-after-free) and release the mutex (or risk a deadlock) WARNING: lock held when returning to user space! 5.5.0-rc6-syzkaller #0 Not tainted ------------------------------------------------ syz-executor.0/455 is leaving the kernel with locks still held! 1 lock held by syz-executor.0/455: #0: ffff888098f6e748 (&tfile->napi_mutex){+.+.}, at: tun_get_user+0x1604/0x3fc0 drivers/net/tun.c:1835 Fixes: 90e33d45 ("tun: enable napi_gro_frags() for TUN/TAP driver") Signed-off-by:Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Cc: Petar Penkov <ppenkov@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Ido Schimmel authored
During reload (or module unload), the router block is de-initialized. Among other things, this results in the removal of a default multicast route from each active virtual router (VRF). These default routes are configured during initialization to trap packets to the CPU. In Spectrum-2, unlike Spectrum-1, multicast routes are implemented using ACL rules. Since the router block is de-initialized before the ACL block, it is possible that the ACL rules corresponding to the default routes are deleted while being accessed by the ACL delayed work that queries rules' activity from the device. This can result in a rare use-after-free [1]. Fix this by protecting the rules list accessed by the delayed work with a lock. We cannot use a spinlock as the activity read operation is blocking. [1] [ 123.331662] ================================================================== [ 123.339920] BUG: KASAN: use-after-free in mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0 [ 123.349381] Read of size 8 at addr ffff8881f3bb4520 by task kworker/0:2/78 [ 123.357080] [ 123.358773] CPU: 0 PID: 78 Comm: kworker/0:2 Not tainted 5.5.0-rc5-custom-33108-gf5df95d3ef41 #2209 [ 123.368898] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018 [ 123.378456] Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work [ 123.385970] Call Trace: [ 123.388734] dump_stack+0xc6/0x11e [ 123.392568] print_address_description.constprop.4+0x21/0x340 [ 123.403236] __kasan_report.cold.8+0x76/0xb1 [ 123.414884] kasan_report+0xe/0x20 [ 123.418716] mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0 [ 123.444034] process_one_work+0xb06/0x19a0 [ 123.453731] worker_thread+0x91/0xe90 [ 123.467348] kthread+0x348/0x410 [ 123.476847] ret_from_fork+0x24/0x30 [ 123.480863] [ 123.482545] Allocated by task 73: [ 123.486273] save_stack+0x19/0x80 [ 123.490000] __kasan_kmalloc.constprop.6+0xc1/0xd0 [ 123.495379] mlxsw_sp_acl_rule_create+0xa7/0x230 [ 123.500566] mlxsw_sp2_mr_tcam_route_create+0xf6/0x3e0 [ 123.506334] mlxsw_sp_mr_tcam_route_create+0x5b4/0x820 [ 123.512102] mlxsw_sp_mr_table_create+0x3b5/0x690 [ 123.517389] mlxsw_sp_vr_get+0x289/0x4d0 [ 123.521797] mlxsw_sp_fib_node_get+0xa2/0x990 [ 123.526692] mlxsw_sp_router_fib4_event_work+0x54c/0x2d60 [ 123.532752] process_one_work+0xb06/0x19a0 [ 123.537352] worker_thread+0x91/0xe90 [ 123.541471] kthread+0x348/0x410 [ 123.545103] ret_from_fork+0x24/0x30 [ 123.549113] [ 123.550795] Freed by task 518: [ 123.554231] save_stack+0x19/0x80 [ 123.557958] __kasan_slab_free+0x125/0x170 [ 123.562556] kfree+0xd7/0x3a0 [ 123.565895] mlxsw_sp_acl_rule_destroy+0x63/0xd0 [ 123.571081] mlxsw_sp2_mr_tcam_route_destroy+0xd5/0x130 [ 123.576946] mlxsw_sp_mr_tcam_route_destroy+0xba/0x260 [ 123.582714] mlxsw_sp_mr_table_destroy+0x1ab/0x290 [ 123.588091] mlxsw_sp_vr_put+0x1db/0x350 [ 123.592496] mlxsw_sp_fib_node_put+0x298/0x4c0 [ 123.597486] mlxsw_sp_vr_fib_flush+0x15b/0x360 [ 123.602476] mlxsw_sp_router_fib_flush+0xba/0x470 [ 123.607756] mlxsw_sp_vrs_fini+0xaa/0x120 [ 123.612260] mlxsw_sp_router_fini+0x137/0x384 [ 123.617152] mlxsw_sp_fini+0x30a/0x4a0 [ 123.621374] mlxsw_core_bus_device_unregister+0x159/0x600 [ 123.627435] mlxsw_devlink_core_bus_device_reload_down+0x7e/0xb0 [ 123.634176] devlink_reload+0xb4/0x380 [ 123.638391] devlink_nl_cmd_reload+0x610/0x700 [ 123.643382] genl_rcv_msg+0x6a8/0xdc0 [ 123.647497] netlink_rcv_skb+0x134/0x3a0 [ 123.651904] genl_rcv+0x29/0x40 [ 123.655436] netlink_unicast+0x4d4/0x700 [ 123.659843] netlink_sendmsg+0x7c0/0xc70 [ 123.664251] __sys_sendto+0x265/0x3c0 [ 123.668367] __x64_sys_sendto+0xe2/0x1b0 [ 123.672773] do_syscall_64+0xa0/0x530 [ 123.676892] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 123.682552] [ 123.684238] The buggy address belongs to the object at ffff8881f3bb4500 [ 123.684238] which belongs to the cache kmalloc-128 of size 128 [ 123.698261] The buggy address is located 32 bytes inside of [ 123.698261] 128-byte region [ffff8881f3bb4500, ffff8881f3bb4580) [ 123.711303] The buggy address belongs to the page: [ 123.716682] page:ffffea0007ceed00 refcount:1 mapcount:0 mapping:ffff888236403500 index:0x0 [ 123.725958] raw: 0200000000000200 dead000000000100 dead000000000122 ffff888236403500 [ 123.734646] raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000 [ 123.743315] page dumped because: kasan: bad access detected [ 123.749562] [ 123.751241] Memory state around the buggy address: [ 123.756620] ffff8881f3bb4400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 123.764716] ffff8881f3bb4480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 123.772812] >ffff8881f3bb4500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 123.780904] ^ [ 123.785697] ffff8881f3bb4580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 123.793793] ffff8881f3bb4600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 123.801883] ================================================================== Fixes: cf7221a4 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2") Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
David S. Miller authored
Hayes Wang says: ==================== r8152: serial fixes v3: 1. Fix the typos for patch #5 and #6. 2. Modify the commit message of patch #9. v2: For patch #2, move declaring the variable "ocp_data". v1: These patches are used to fix some issues for RTL8153. ==================== Signed-off-by: -
Hayes Wang authored
When enabling this, the device would wait an internal signal which wouldn't be triggered. Then, the device couldn't enter P3 mode, so the power consumption is increased. Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
Hayes Wang authored
Avoid the MCU to clear the lanwake after suspending. It may cause the WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it and reset the lanwake status when resuming or initializing. Signed-off-by:
-
Hayes Wang authored
For certain platforms, it causes USB reset periodically. Signed-off-by:
-
Hayes Wang authored
For RTL8153B with QFN32, disable test IO. Otherwise, it may cause abnormal behavior for the device randomly. Signed-off-by:
-
Hayes Wang authored
PLA MCU clock speed down could only be enabled when tx/rx are disabled. Otherwise, the packet loss may occur. Signed-off-by:
-
Hayes Wang authored
Enable U2P3 may miss zero packet for bulk-in. Signed-off-by:
-
Hayes Wang authored
Initailization would reset runtime suspend by tp->saved_wolopts, so the tp->saved_wolopts should be set before initializing. Signed-off-by:
-
Hayes Wang authored
When linking ON, the patch of flow control has to be reset. This makes sure the patch works normally. Signed-off-by:
-
Hayes Wang authored
Fix the runtime resume doesn't work normally for linking change. 1. Reset the settings and status of runtime suspend. 2. Sync the linking status. 3. Poll the linking change. Signed-off-by:
-
Eric Dumazet authored
A malicious user could use RAW sockets and fool GTP using them as standard SOCK_DGRAM UDP sockets. BUG: KMSAN: uninit-value in udp_tunnel_encap_enable include/net/udp_tunnel.h:174 [inline] BUG: KMSAN: uninit-value in setup_udp_tunnel_sock+0x45e/0x6f0 net/ipv4/udp_tunnel.c:85 CPU: 0 PID: 11262 Comm: syz-executor613 Not tainted 5.5.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1c9/0x220 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215 udp_tunnel_encap_enable include/net/udp_tunnel.h:174 [inline] setup_udp_tunnel_sock+0x45e/0x6f0 net/ipv4/udp_tunnel.c:85 gtp_encap_enable_socket+0x37f/0x5a0 drivers/net/gtp.c:827 gtp_encap_enable drivers/net/gtp.c:844 [inline] gtp_newlink+0xfb/0x1e50 drivers/net/gtp.c:666 __rtnl_newlink net/core/rtnetlink.c:3305 [inline] rtnl_newlink+0x2973/0x3920 net/core/rtnetlink.c:3363 rtnetlink_rcv_msg+0x1153/0x1570 net/core/rtnetlink.c:5424 netlink_rcv_skb+0x451/0x650 net/netlink/af_netlink.c:2477 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5442 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0xf9e/0x1100 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x1248/0x14d0 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x451/0x5f0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x441359 Code: e8 ac e8 ff ff 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fff1cd0ac28 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000441359 RDX: 0000000000000000 RSI: 0000000020000100 RDI: 0000000000000003 RBP: 00000000006cb018 R08: 00000000004002c8 R09: 00000000004002c8 R10: 00000000004002c8 R11: 0000000000000246 R12: 00000000004020d0 R13: 0000000000402160 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags+0x3c/0x90 mm/kmsan/kmsan.c:144 kmsan_internal_alloc_meta_for_pages mm/kmsan/kmsan_shadow.c:307 [inline] kmsan_alloc_page+0x12a/0x310 mm/kmsan/kmsan_shadow.c:336 __alloc_pages_nodemask+0x57f2/0x5f60 mm/page_alloc.c:4800 alloc_pages_current+0x67d/0x990 mm/mempolicy.c:2207 alloc_pages include/linux/gfp.h:534 [inline] alloc_slab_page+0x111/0x12f0 mm/slub.c:1511 allocate_slab mm/slub.c:1656 [inline] new_slab+0x2bc/0x1130 mm/slub.c:1722 new_slab_objects mm/slub.c:2473 [inline] ___slab_alloc+0x1533/0x1f30 mm/slub.c:2624 __slab_alloc mm/slub.c:2664 [inline] slab_alloc_node mm/slub.c:2738 [inline] slab_alloc mm/slub.c:2783 [inline] kmem_cache_alloc+0xb23/0xd70 mm/slub.c:2788 sk_prot_alloc+0xf2/0x620 net/core/sock.c:1597 sk_alloc+0xf0/0xbe0 net/core/sock.c:1657 inet_create+0x7c7/0x1370 net/ipv4/af_inet.c:321 __sock_create+0x8eb/0xf00 net/socket.c:1420 sock_create net/socket.c:1471 [inline] __sys_socket+0x1a1/0x600 net/socket.c:1513 __do_sys_socket net/socket.c:1522 [inline] __se_sys_socket+0x8d/0xb0 net/socket.c:1520 __x64_sys_socket+0x4a/0x70 net/socket.c:1520 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 459aa660 ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by:
-
Eric Dumazet authored
rtnl_create_link() needs to apply dev->min_mtu and dev->max_mtu checks that we apply in do_setlink() Otherwise malicious users can crash the kernel, for example after an integer overflow : BUG: KASAN: use-after-free in memset include/linux/string.h:365 [inline] BUG: KASAN: use-after-free in __alloc_skb+0x37b/0x5e0 net/core/skbuff.c:238 Write of size 32 at addr ffff88819f20b9c0 by task swapper/0/0 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.5.0-rc1-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x197/0x210 lib/dump_stack.c:118 print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374 __kasan_report.cold+0x1b/0x41 mm/kasan/report.c:506 kasan_report+0x12/0x20 mm/kasan/common.c:639 check_memory_region_inline mm/kasan/generic.c:185 [inline] check_memory_region+0x134/0x1a0 mm/kasan/generic.c:192 memset+0x24/0x40 mm/kasan/common.c:108 memset include/linux/string.h:365 [inline] __alloc_skb+0x37b/0x5e0 net/core/skbuff.c:238 alloc_skb include/linux/skbuff.h:1049 [inline] alloc_skb_with_frags+0x93/0x590 net/core/skbuff.c:5664 sock_alloc_send_pskb+0x7ad/0x920 net/core/sock.c:2242 sock_alloc_send_skb+0x32/0x40 net/core/sock.c:2259 mld_newpack+0x1d7/0x7f0 net/ipv6/mcast.c:1609 add_grhead.isra.0+0x299/0x370 net/ipv6/mcast.c:1713 add_grec+0x7db/0x10b0 net/ipv6/mcast.c:1844 mld_send_cr net/ipv6/mcast.c:1970 [inline] mld_ifc_timer_expire+0x3d3/0x950 net/ipv6/mcast.c:2477 call_timer_fn+0x1ac/0x780 kernel/time/timer.c:1404 expire_timers kernel/time/timer.c:1449 [inline] __run_timers kernel/time/timer.c:1773 [inline] __run_timers kernel/time/timer.c:1740 [inline] run_timer_softirq+0x6c3/0x1790 kernel/time/timer.c:1786 __do_softirq+0x262/0x98c kernel/softirq.c:292 invoke_softirq kernel/softirq.c:373 [inline] irq_exit+0x19b/0x1e0 kernel/softirq.c:413 exiting_irq arch/x86/include/asm/apic.h:536 [inline] smp_apic_timer_interrupt+0x1a3/0x610 arch/x86/kernel/apic/apic.c:1137 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:829 </IRQ> RIP: 0010:native_safe_halt+0xe/0x10 arch/x86/include/asm/irqflags.h:61 Code: 98 6b ea f9 eb 8a cc cc cc cc cc cc e9 07 00 00 00 0f 00 2d 44 1c 60 00 f4 c3 66 90 e9 07 00 00 00 0f 00 2d 34 1c 60 00 fb f4 <c3> cc 55 48 89 e5 41 57 41 56 41 55 41 54 53 e8 4e 5d 9a f9 e8 79 RSP: 0018:ffffffff89807ce8 EFLAGS: 00000286 ORIG_RAX: ffffffffffffff13 RAX: 1ffffffff13266ae RBX: ffffffff8987a1c0 RCX: 0000000000000000 RDX: dffffc0000000000 RSI: 0000000000000006 RDI: ffffffff8987aa54 RBP: ffffffff89807d18 R08: ffffffff8987a1c0 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: dffffc0000000000 R13: ffffffff8a799980 R14: 0000000000000000 R15: 0000000000000000 arch_cpu_idle+0xa/0x10 arch/x86/kernel/process.c:690 default_idle_call+0x84/0xb0 kernel/sched/idle.c:94 cpuidle_idle_call kernel/sched/idle.c:154 [inline] do_idle+0x3c8/0x6e0 kernel/sched/idle.c:269 cpu_startup_entry+0x1b/0x20 kernel/sched/idle.c:361 rest_init+0x23b/0x371 init/main.c:451 arch_call_rest_init+0xe/0x1b start_kernel+0x904/0x943 init/main.c:784 x86_64_start_reservations+0x29/0x2b arch/x86/kernel/head64.c:490 x86_64_start_kernel+0x77/0x7b arch/x86/kernel/head64.c:471 secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:242 The buggy address belongs to the page: page:ffffea00067c82c0 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 raw: 057ffe0000000000 ffffea00067c82c8 ffffea00067c82c8 0000000000000000 raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88819f20b880: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff88819f20b900: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >ffff88819f20b980: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ^ ffff88819f20ba00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff88819f20ba80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Fixes: 61e84623 ("net: centralize net_device min/max MTU checking") Signed-off-by: -
Michael Ellerman authored
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c), implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl(). The ioctl handler copies an aironet_ioctl struct from userspace, which includes a command. Some of the commands are handled in readrids(), where the user controlled command is converted into a driver-internal value called "ridcode". There are two command values, AIROGWEPKTMP and AIROGWEPKNV, which correspond to ridcode values of RID_WEP_TEMP and RID_WEP_PERM respectively. These commands both have checks that the user has CAP_NET_ADMIN, with the comment that "Only super-user can read WEP keys", otherwise they return -EPERM. However there is another command value, AIRORRID, that lets the user specify the ridcode value directly, with no other checks. This means the user can bypass the CAP_NET_ADMIN check on AIROGWEPKTMP and AIROGWEPKNV. Fix it by moving the CAP_NET_ADMIN check out of the command handling and instead do it later based on the ridcode. That way regardless of whether the ridcode is set via AIROGWEPKTMP or AIROGWEPKNV, or passed in using AIRORID, we always do the CAP_NET_ADMIN check. Found by Ilja by code inspection, not tested as I don't have the required hardware. Reported-by:
Ilja Van Sprundel <ivansprundel@ioactive.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Michael Ellerman authored
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c), implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl(). The ioctl handler copies an aironet_ioctl struct from userspace, which includes a command and a length. Some of the commands are handled in readrids(), which kmalloc()'s a buffer of RIDSIZE (2048) bytes. That buffer is then passed to PC4500_readrid(), which has two cases. The else case does some setup and then reads up to RIDSIZE bytes from the hardware into the kmalloc()'ed buffer. Here len == RIDSIZE, pBuf is the kmalloc()'ed buffer: // read the rid length field bap_read(ai, pBuf, 2, BAP1); // length for remaining part of rid len = min(len, (int)le16_to_cpu(*(__le16*)pBuf)) - 2; ... // read remainder of the rid rc = bap_read(ai, ((__le16*)pBuf)+1, len, BAP1); PC4500_readrid() then returns to readrids() which does: len = comp->len; if (copy_to_user(comp->data, iobuf, min(len, (int)RIDSIZE))) { Where comp->len is the user controlled length field. So if the "rid length field" returned by the hardware is < 2048, and the user requests 2048 bytes in comp->len, we will leak the previous contents of the kmalloc()'ed buffer to userspace. Fix it by kzalloc()'ing the buffer. Found by Ilja by code inspection, not tested as I don't have the required hardware. Reported-by: -
Andrew Lunn authored
phylink and phylib are interconnected. It makes sense for phylib and phy driver patches to be also reviewed by the phylink maintainer. So add Russell King as a designed reviewer of phylib. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
- 22 Jan, 2020 3 commits
-
-
William Dauchy authored
in the same manner as commit d0f41851 ("net, ip_tunnel: fix namespaces move"), fix namespace moving as it was broken since commit 8d79266b ("ip6_tunnel: add collect_md mode to IPv6 tunnel"), but for ipv6 this time; there is no reason to keep it for ip6_tunnel. Fixes: 8d79266b ("ip6_tunnel: add collect_md mode to IPv6 tunnel") Signed-off-by:
William Dauchy <w.dauchy@criteo.com> Acked-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Eric Dumazet authored
sysbot found another issue in tc_new_tfilter(). We probably should use @name which contains the sanitized version of TCA_KIND. BUG: KMSAN: uninit-value in string_nocheck lib/vsprintf.c:608 [inline] BUG: KMSAN: uninit-value in string+0x522/0x690 lib/vsprintf.c:689 CPU: 1 PID: 10753 Comm: syz-executor.1 Not tainted 5.5.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1c9/0x220 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215 string_nocheck lib/vsprintf.c:608 [inline] string+0x522/0x690 lib/vsprintf.c:689 vsnprintf+0x207d/0x31b0 lib/vsprintf.c:2574 __request_module+0x2ad/0x11c0 kernel/kmod.c:143 tcf_proto_lookup_ops+0x241/0x720 net/sched/cls_api.c:139 tcf_proto_create net/sched/cls_api.c:262 [inline] tc_new_tfilter+0x2a4e/0x5010 net/sched/cls_api.c:2058 rtnetlink_rcv_msg+0xcb7/0x1570 net/core/rtnetlink.c:5415 netlink_rcv_skb+0x451/0x650 net/netlink/af_netlink.c:2477 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5442 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0xf9e/0x1100 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x1248/0x14d0 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x451/0x5f0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x45b349 Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f88b3948c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007f88b39496d4 RCX: 000000000045b349 RDX: 0000000000000000 RSI: 00000000200001c0 RDI: 0000000000000003 RBP: 000000000075bfc8 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff R13: 000000000000099f R14: 00000000004cb163 R15: 000000000075bfd4 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline] kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127 kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:82 slab_alloc_node mm/slub.c:2774 [inline] __kmalloc_node_track_caller+0xb40/0x1200 mm/slub.c:4382 __kmalloc_reserve net/core/skbuff.c:141 [inline] __alloc_skb+0x2fd/0xac0 net/core/skbuff.c:209 alloc_skb include/linux/skbuff.h:1049 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1174 [inline] netlink_sendmsg+0x7d3/0x14d0 net/netlink/af_netlink.c:1892 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x451/0x5f0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 6f96c3c6 ("net_sched: fix backward compatibility for TCA_KIND") Signed-off-by:
-
Paolo Abeni authored
This reverts commit 0d4a6608. Williem reported that after commit 0d4a6608 ("udp: do rmem bulk free even if the rx sk queue is empty") the memory allocated by an almost idle system with many UDP sockets can grow a lot. For stable kernel keep the solution as simple as possible and revert the offending commit. Reported-by:
Willem de Bruijn <willemdebruijn.kernel@gmail.com> Diagnosed-by:
Eric Dumazet <eric.dumazet@gmail.com> Fixes: 0d4a6608 ("udp: do rmem bulk free even if the rx sk queue is empty") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Acked-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
