BLE based 6LoWPAN networks are highly constrained in bandwidth.
Do not take a short-cut, always check if the destination address is
known to belong to a peer.

As a side-effect this also removes any behavioral differences between
one, and two or more connected peers.
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Tested-by: Michael Scott <mike@foundries.io>
Signed-off-by: Josua Mayer <josua.mayer@jm0.eu>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Like any IPv6 capable device, 6LNs can have multiple addresses assigned
using SLAAC and made known through neighbour advertisements.
After checking the destination address against all peers link-local
addresses, consult the neighbour cache for additional known addresses.

RFC7668 defines the scope of Neighbor Advertisements in Section 3.2.3:
1. "A Bluetooth LE 6LN MUST NOT register its link-local address"
2. "A Bluetooth LE 6LN MUST register its non-link-local addresses with
the 6LBR by sending Neighbor Solicitation (NS) messages ..."

Due to these constranits both the link-local addresses tracked in the
list of 6lowpan peers, and the neighbour cache have to be used when
identifying the 6lowpan peer for a destination address.
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Tested-by: Michael Scott <mike@foundries.io>
Signed-off-by: Josua Mayer <josua.mayer@jm0.eu>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Handle overlooked case where the target address is assigned to a peer
and neither route nor gateway exist.

For one peer, no checks are performed to see if it is meant to receive
packets for a given address.

As soon as there is a second peer however, checks are performed
to deal with routes and gateways for handling complex setups with
multiple hops to a target address.
This logic assumed that no route and no gateway imply that the
destination address can not be reached, which is false in case of a
direct peer.
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Tested-by: Michael Scott <mike@foundries.io>
Signed-off-by: Josua Mayer <josua.mayer@jm0.eu>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Microsoft Surface Precision Mouse provides bogus identity address when
pairing. It connects with Static Random address but provides Public
Address in SMP Identity Address Information PDU. Address has same
value but type is different. Workaround this by dropping IRK if ID
address discrepancy is detected.

> HCI Event: LE Meta Event (0x3e) plen 19
      LE Connection Complete (0x01)
        Status: Success (0x00)
        Handle: 75
        Role: Master (0x00)
        Peer address type: Random (0x01)
        Peer address: E0:52:33:93:3B:21 (Static)
        Connection interval: 50.00 msec (0x0028)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Master clock accuracy: 0x00

....

> ACL Data RX: Handle 75 flags 0x02 dlen 12
      SMP: Identity Address Information (0x09) len 7
        Address type: Public (0x00)
        Address: E0:52:33:93:3B:21
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Tested-by: Maarten Fonville <maarten.fonville@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199461
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The spec defines PSM and LE_PSM as different domains so a listen on the
same PSM is valid if the address type points to a different bearer.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This makes use of controller sets when using Extended Advertising
feature thus offloading the scheduling to the controller.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Problem: The Linux Bluetooth stack yields complete control over the BLE
connection interval to the remote device.

The Linux Bluetooth stack provides access to the BLE connection interval
min and max values through /sys/kernel/debug/bluetooth/hci0/
conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval.
These values are used for initial BLE connections, but the remote device
has the ability to request a connection parameter update. In the event
that the remote side requests to change the connection interval, the Linux
kernel currently only validates that the desired value is within the
acceptable range in the Bluetooth specification (6 - 3200, corresponding to
7.5ms - 4000ms). There is currently no validation that the desired value
requested by the remote device is within the min/max limits specified in
the conn_min_interval/conn_max_interval configurations. This essentially
leads to Linux yielding complete control over the connection interval to
the remote device.

The proposed patch adds a verification step to the connection parameter
update mechanism, ensuring that the desired value is within the min/max
bounds of the current connection. If the desired value is outside of the
current connection min/max values, then the connection parameter update
request is rejected and the negative response is returned to the remote
device. Recall that the initial connection is established using the local
conn_min_interval/conn_max_interval values, so this allows the Linux
administrator to retain control over the BLE connection interval.

The one downside that I see is that the current default Linux values for
conn_min_interval and conn_max_interval typically correspond to 30ms and
50ms respectively. If this change were accepted, then it is feasible that
some devices would no longer be able to negotiate to their desired
connection interval values. This might be remedied by setting the default
Linux conn_min_interval and conn_max_interval values to the widest
supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same
behavior as the current implementation, where the remote device could
request to change the connection interval value to any value that is
permitted by the Bluetooth specification, and Linux would accept the
desired value.
Signed-off-by: Carey Sonsino <csonsino@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Changes made to add HCI Write Authenticated Payload timeout
command for LE Ping feature.

As per the Core Specification 5.0 Volume 2 Part E Section 7.3.94,
the following code changes implements
HCI Write Authenticated Payload timeout command for LE Ping feature.
Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Because of both sides doing L2CAP disconnection at the same time, it
was possible to receive L2CAP Disconnection Response with CID that was
already freed. That caused problems if CID was already reused and L2CAP
Connection Request with same CID was sent out. Before this patch kernel
deleted channel context regardless of the state of the channel.

Example where leftover Disconnection Response (frame #402) causes local
device to delete L2CAP channel which was not yet connected. This in
turn confuses remote device's stack because same CID is re-used without
properly disconnecting.

Btmon capture before patch:
** snip **
> ACL Data RX: Handle 43 flags 0x02 dlen 8                #394 [hci1] 10.748949
      Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
      RFCOMM: Disconnect (DISC) (0x43)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x53 poll/final 1
         Length: 0
         FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8                #395 [hci1] 10.749062
      Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
      RFCOMM: Unnumbered Ack (UA) (0x63)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x73 poll/final 1
         Length: 0
         FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #396 [hci1] 10.749073
      L2CAP: Disconnection Request (0x06) ident 17 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Packets (0x13) plen 5    #397 [hci1] 10.752391
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5    #398 [hci1] 10.753394
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #399 [hci1] 10.756499
      L2CAP: Disconnection Request (0x06) ident 26 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #400 [hci1] 10.756548
      L2CAP: Disconnection Response (0x07) ident 26 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #401 [hci1] 10.757459
      L2CAP: Connection Request (0x02) ident 18 len 4
        PSM: 1 (0x0001)
        Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #402 [hci1] 10.759148
      L2CAP: Disconnection Response (0x07) ident 17 len 4
        Destination CID: 65
        Source CID: 65
= bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o..   10.759447
> HCI Event: Number of Completed Packets (0x13) plen 5    #403 [hci1] 10.759386
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #404 [hci1] 10.760397
      L2CAP: Connection Request (0x02) ident 27 len 4
        PSM: 3 (0x0003)
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16               #405 [hci1] 10.760441
      L2CAP: Connection Response (0x03) ident 27 len 8
        Destination CID: 65
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27               #406 [hci1] 10.760449
      L2CAP: Configure Request (0x04) ident 19 len 19
        Destination CID: 65
        Flags: 0x0000
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 1013
        Option: Retransmission and Flow Control (0x04) [mandatory]
          Mode: Basic (0x00)
          TX window size: 0
          Max transmit: 0
          Retransmission timeout: 0
          Monitor timeout: 0
          Maximum PDU size: 0
> HCI Event: Number of Completed Packets (0x13) plen 5    #407 [hci1] 10.761399
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 16               #408 [hci1] 10.762942
      L2CAP: Connection Response (0x03) ident 18 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
*snip*

Similar case after the patch:
*snip*
> ACL Data RX: Handle 43 flags 0x02 dlen 8            #22702 [hci0] 1664.411056
      Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
      RFCOMM: Disconnect (DISC) (0x43)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x53 poll/final 1
         Length: 0
         FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8            #22703 [hci0] 1664.411136
      Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
      RFCOMM: Unnumbered Ack (UA) (0x63)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x73 poll/final 1
         Length: 0
         FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22704 [hci0] 1664.411143
      L2CAP: Disconnection Request (0x06) ident 11 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22705 [hci0] 1664.414009
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22706 [hci0] 1664.415007
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22707 [hci0] 1664.418674
      L2CAP: Disconnection Request (0x06) ident 17 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22708 [hci0] 1664.418762
      L2CAP: Disconnection Response (0x07) ident 17 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22709 [hci0] 1664.421073
      L2CAP: Connection Request (0x02) ident 12 len 4
        PSM: 1 (0x0001)
        Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22710 [hci0] 1664.421371
      L2CAP: Disconnection Response (0x07) ident 11 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22711 [hci0] 1664.424082
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22712 [hci0] 1664.425040
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22713 [hci0] 1664.426103
      L2CAP: Connection Request (0x02) ident 18 len 4
        PSM: 3 (0x0003)
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16           #22714 [hci0] 1664.426186
      L2CAP: Connection Response (0x03) ident 18 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27           #22715 [hci0] 1664.426196
      L2CAP: Configure Request (0x04) ident 13 len 19
        Destination CID: 65
        Flags: 0x0000
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 1013
        Option: Retransmission and Flow Control (0x04) [mandatory]
          Mode: Basic (0x00)
          TX window size: 0
          Max transmit: 0
          Retransmission timeout: 0
          Monitor timeout: 0
          Maximum PDU size: 0
> ACL Data RX: Handle 43 flags 0x02 dlen 16           #22716 [hci0] 1664.428804
      L2CAP: Connection Response (0x03) ident 12 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
*snip*

Fix is to check that channel is in state BT_DISCONN before deleting the
channel.

This bug was found while fuzzing Bluez's OBEX implementation using
Synopsys Defensics.
Reported-by: Matti Kamunen <matti.kamunen@synopsys.com>
Reported-by: Ari Timonen <ari.timonen@synopsys.com>
Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This change is similar to commit a1616a5a ("Bluetooth: hidp: fix
buffer overflow") but for the compat ioctl.  We take a string from the
user and forgot to ensure that it's NUL terminated.

I have also changed the strncpy() in to strscpy() in hidp_setup_hid().
The difference is the strncpy() doesn't necessarily NUL terminate the
destination string.  Either change would fix the problem but it's nice
to take a belt and suspenders approach and do both.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Without the QCA ROME setup routine this adapter fails to establish a SCO
connection.

T:  Bus=01 Lev=01 Prnt=01 Port=08 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3491 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Without the QCA ROME setup routine this adapter fails to establish a SCO
connection.

T:  Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3501 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Syzkaller found that it is possible to provoke a memory leak by
never freeing rx_skb in struct bcsp_struct.

Fix by freeing in bcsp_close()
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+98162c885993b72f19c4@syzkaller.appspotmail.com
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This device is functionally equivalent to the BT part of the RTL8723DE,
uses the same firmware, but the LMP subversion and HCI revision are unique.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Some board requires explicitily control external osscilator via GPIO.
So, add an implementation of a clock property for an external oscillator
to the device.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Not every platform has the pinctrl device integrates the GPIO the function
such as MT7621 whose pinctrl and GPIO are separate hardware so the driver
adds additional boot-gpios to let the MT766[3,8]U can enter the proper boot
mode by gpiod for such platform.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Some board requires explicitily control external osscilator via GPIO.
So, add a clock property for an external oscillator for the device.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Not every platform has the pinctrl device integrates the GPIO the function
such as MT7621 whose pinctrl and GPIO are separate hardware so adding an
additional boot-gpios property for such platform allows them to bring up
the device.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The BCM4359C0 BT/Wi-Fi compo chip needs an entry to be discovered
by the btbcm driver.

Tested using an AP6398S module from Ampak.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds an optional device property "firmware-name" to allow the
driver to load customized nvm firmware file based on this property.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

QCA BTSOC NVM is a customized firmware file and different vendors may
want to have different BTSOC configuration (e.g. Configure SCO over PCM
or I2S, Setting Tx power, etc.) via this file. This patch will allow
vendors to download different NVM firmware file by reading a device
property "firmware-name".
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Tested-by: Harish Bandi <c-hbandi@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This adds serdev support to the Marvell hci uart driver. Only basic
serdev support, none of the fancier features like regulator or enable
GPIO support is added for now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

For the Marvell HCI UART we have to upload two firmware files. The first
one is only for switching the baudrate of the device to a higher
baudrate. After the baudrate switching firmware has been uploaded the
device waits for a final ack (0x5a) before actually switching the
baudrate. To send this final ack with the old baudrate give the hci
ldisc workqueue a chance to run before switching the baudrate. Without
this the final ack will never be received by the device and firmware
upload fails.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The hci UART line discipline sends its characters in a workqueue. Some
devices like the Marvell Bluetooth chips need to make sure that all
queued characters are sent before switching the baudrate. This adds
a function to synchronize with the workqueue.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.

Because we don't care if debugfs works or not, this trickles back a bit
so we can clean things up by making some functions return void instead
of an error value that is never going to fail.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Firmware download to the WCN3990 often fails with a 'TLV response size
mismatch' error:

[  133.064659] Bluetooth: hci0: setting up wcn3990
[  133.489150] Bluetooth: hci0: QCA controller version 0x02140201
[  133.495245] Bluetooth: hci0: QCA Downloading qca/crbtfw21.tlv
[  133.507214] Bluetooth: hci0: QCA TLV response size mismatch
[  133.513265] Bluetooth: hci0: QCA Failed to download patch (-84)

This is caused by a vendor event that corresponds to an earlier command
to change the baudrate. The event is not processed in the context of the
baudrate change and is later interpreted as response to the firmware
download command (which is also a vendor command), but the driver detects
that the event doesn't have the expected amount of associated data.

More details:

For the WCN3990 the vendor command for a baudrate change isn't sent as
synchronous HCI command, because the controller sends the corresponding
vendor event with the new baudrate. The event is received and decoded
after the baudrate change of the host port.

Identify the 'unused' event when it is received and don't add it to
the queue of RX frames.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Latest qualcomm chips are not sending an command complete event for
every firmware packet sent to chip. They only respond with a vendor
specific event for the last firmware packet. This optimization will
decrease the BT ON time. Due to this we are seeing a timeout error
message logs on the console during firmware download. Now we are
injecting a command complete event once we receive an vendor specific
event for the last RAM firmware packet.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Fix some warnings and one error reported by checkpatch.pl:
- lines longer than 80 characters are wrapped
- empty lines inserted to separate variable declarations from the actual
  code
- line break inserted after if (...)
Co-developed-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de>
Signed-off-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de>
Signed-off-by: Fabian Schindlatz <fabian.schindlatz@fau.de>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Realtek RTL8822BE BT chip on ASUS X420FA cannot be turned on correctly
after on-off several times. Bluetooth daemon sets BT mode failed when
this issue happens. Scanning must be active while turning off for this
bug to be hit.

bluetoothd[1576]: Failed to set mode: Failed (0x03)

If BT is turned off, then turned on again, it works correctly again.

According to the vendor driver, the HCI_QUIRK_RESET_ON_CLOSE flag is set
during probing. So, this patch makes Realtek's BT reset on close to fix
this issue.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=203429Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Extract the new function send_command_from_firmware from
download_firmware, which helps with the readability of the switch
statement. This way the code is less deeply nested and also no longer
exceeds the 80 character limit.
Co-developed-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de>
Signed-off-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de>
Signed-off-by: Fabian Schindlatz <fabian.schindlatz@fau.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Uploading the firmware needs quite a few seconds if done at 115200 kbps. So set
the operational frequency, usually 3 MHz, before uploading the firmware.

I have successfully tested this with a wl1837mod.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

BCM4356 devices soldered onto the PCB (non-removable) use an UART
connection for bluetooth, such as the Rock960, but it also advertise
btsdio support as a sdio function.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
CC: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Tariq Toukan says:

====================
mlx5 TLS TX HW offload support

This series from Eran and me, adds TLS TX HW offload support to
the mlx5 driver.

This offloads the kTLS encryption process from kernel to the
Mellanox NIC, saving CPU cycles and improving utilization.

Upon a new TLS connection request, driver is responsible to create
a dedicated HW context and configure it according to the crypto info,
so HW can do the encryption itself.

When the HW context gets out-of-sync (i.e. due to packets retransmission),
driver is responsible for the re-sync process.
This is done by posting special resync descriptors to the HW.

Feature is supported on Mellanox Connect-X 6DX, and newer.
Series was tested on SimX simulator.

Series generated against net-next commit [1], with Saeed's request pulled [2]:

[1] c4cde580 Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
[2] git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux.git tags/mlx5-updates-2019-07-04-v2

Changes from last pull request:
Fixed comments from Jakub:
Patch 4:
- Replace zero  memset with a call to memzero_explicit().
Patch 11:
- Fix stats counters names.
- Drop TLS SKB with non-matching netdev.
====================
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for transmit side kernel-TLS acceleration.
Offload the crypto encryption to HW.

Per TLS connection:
- Use a separate TIS to maintain the HW context.
- Use a separate encryption key.
- Maintain static and progress HW contexts by posting the proper
  WQEs at creation time, or upon resync.
- Use a special DUMP opcode to replay the previous frags and sync
  the HW context.

To make sure the SQ is able to serve an xmit request, increase
SQ stop room to cover:
- static params WQE,
- progress params WQE, and
- resync DUMP per frag.

Currently supporting TLS 1.2, and key size 128bit.

Tested over SimX simulator.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to the existing mlx5e_post_nop(), but marks a fence
in the WQE control segment.

Added as a separate new function to not hurt the performance
of the common case.

To be used in a downstream patch of the series.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Let the EN TIS creation function (mlx5e_create_tis) be responsible
for applying common mdev related fields.
Other specific fields must be set by the caller and passed within
the inbox.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use an SQ field for stop_room, and use the larger value only if TLS
is supported.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When polling a CQE of an SKB-less WQE, don't assume it consumed only
one WQEBB. Use wi->num_wqebbs directly instead.
In the downstream patch, SKB-less WQEs might have more the one WQEBB,
thus this change is needed.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change mlx5e_sq_fetch_wqe to be agnostic to the Work Queue
Element (WQE) type.
Before this patch, it was specific for struct mlx5e_tx_wqe.

In order to allow the change, the function now returns the
generic void pointer, and gets the WQE size to do the zero
memset.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When ctrl->tisn field exists, this indicates an operation (HW offload)
on the TCP payload.
For such WQEs, inline the headers up to L4.

This is in preparation for kTLS HW offload support, added in
a downstream patch.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>