Online self tests are not disruptive and can be run in NPAR mode
and in multi-host NIC as well.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-3-git-send-email-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If NVRAM resources are locked, NVM writes are not permitted. In such
scenarios, firmware returns HWRM_ERR_CODE_RESOURCE_LOCKED error to
firmware commands.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-2-git-send-email-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'linux-can-next-for-5.10-20201012' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
linux-can-next-for-5.10-20201012

Both patches are by Oliver Hartkopp, the first one addresses Jakub's review
comments of the ISOTP protocol, the other one removes version strings from
various CAN protocols.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use netdev_err for better device identification in syslog.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When the router is rebooted without a power cycle, the USB device
remains connected but its configuration is reset. This results in
a non-working ethernet connection with messages like this in syslog:
	usb 2-2: RX packet too long: 65535 B

Re-enable ethernet mode when receiving a packet with invalid size of
0xffff.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

As pointed out by Jakub Kicinski here:
http://lore.kernel.org/r/20201009175751.5c54097f@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com
this patch removes the obsolete version information of the different
CAN protocols and the AF_CAN core module.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201012074354.25839-2-socketcan@hartkopp.netSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

As pointed out by Jakub Kicinski here:
http://lore.kernel.org/r/20201009175751.5c54097f@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com
this patch addresses the remarked issues:

- remove empty line in comment
- remove default=y for CAN_ISOTP in Kconfig
- make use of pr_notice_once()
- use GFP_ATOMIC instead of gfp_any() in soft hrtimer context

The version strings in the CAN subsystem are removed by a separate patch.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201012074354.25839-1-socketcan@hartkopp.netSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Vladimir Oltean says:

====================
Offload tc-vlan mangle to mscc_ocelot switch

This series offloads one more action to the VCAP IS1 ingress TCAM, which
is to change the classified VLAN for packets, according to the VCAP IS1
keys (VLAN, source MAC, source IP, EtherType, etc).
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Create a test that changes a VLAN ID from 200 to 300.

We also need to modify the preferences of the filters installed for the
other rules so that they are unique, because we now install the "tc-vlan
modify" filter in VCAP IS1 only temporarily, and we need to perform the
deletion by filter preference number.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When the Extraction Frame Header contains a valid classified VLAN, use
that instead of the VLAN header present in the packet.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The VCAP_IS1_ACT_VID_REPLACE_ENA action, from the VCAP IS1 ingress TCAM,
changes the classified VLAN.

We are only exposing this ability for switch ports that are under VLAN
aware bridges. This is because in standalone ports mode and under a
bridge with vlan_filtering=0, the ocelot driver configures the switch to
operate as VLAN-unaware, so the classified VLAN is not derived from the
802.1Q header from the packet, but instead is always equal to the
port-based VLAN ID of the ingress port. We _can_ still change the
classified VLAN for packets when operating in this mode, but the end
result will most likely be a drop, since both the ingress and the egress
port need to be members of the modified VLAN. And even if we install the
new classified VLAN into the VLAN table of the switch, the result would
still not be as expected: we wouldn't see, on the output port, the
modified VLAN tag, but the original one, even though the classified VLAN
was indeed modified. This is because of how the hardware works: on
egress, what is pushed to the frame is a "port tag", which gives us the
following options:

- Tag all frames with port tag (derived from the classified VLAN)
- Tag all frames with port tag, except if the classified VLAN is 0 or
  equal to the native VLAN of the egress port
- No port tag

Needless to say, in VLAN-unaware mode we are disabling the port tag.
Otherwise, the existing VLAN tag would be ignored, and a second VLAN
tag (the port tag), holding the classified VLAN, would be pushed
(instead of replacing the existing 802.1Q tag). This is definitely not
what the user wanted when installing a "vlan modify" action.

So it is simply not worth bothering with VLAN modify rules under other
configurations except when the ports are fully VLAN-aware.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Claudiu Manoil says:

====================
enetc: Migrate to PHYLINK and PCS_LYNX

Transitioning the enetc driver from phylib to phylink.
Offloading the serdes configuration to the PCS_LYNX
module is a mandatory part of this transition. Aiming
for a cleaner, more maintainable design, and better
code reuse.
The first 2 patches are clean up prerequisites.

Tested on a p1028rdb board.

v2: validate() explicitly rejects now all interface modes not
supported by the driver instead of relying on the device tree
to provide only supported interfaces, and dropped redundant
activation of pcs_poll (addressing Ioana's findings)
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This is a methodical transition of the driver from phylib
to phylink, following the guidelines from sfp-phylink.rst.
The MAC register configurations based on interface mode
were moved from the probing path to the mac_config() hook.
MAC enable and disable commands (enabling Rx and Tx paths
at MAC level) were also extracted and assigned to their
corresponding phylink hooks.
As part of the migration to phylink, the serdes configuration
from the driver was offloaded to the PCS_LYNX module,
introduced in commit 0da4c3d3 ("net: phy: add Lynx PCS module"),
the PCS_LYNX module being a mandatory component required to
make the enetc driver work with phylink.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.cionei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

As part of the transition of the enetc ethernet driver from phylib
to phylink, the in-band operation mode of the SGMII interface
from enetc port 0 needs to be specified explicitly for phylink.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Decouple internal mdio bus creation from serdes
configuration, as a prerequisite to offloading
serdes configuration to a different module.
Group together mdio bus creation routines, cleanup.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Decouple level MAC configuration based on phy interface type
from general port configuration.
Group together MAC and link configuration code.
Decouple external mdio bus creation from interface type
parsing.  No longer return an (unhandled) error code when
phy_node not found, use phy_node to indicate whether the
port has a phy or not.  No longer fall-through when serdes
configuration fails for the link modes that require
internal link configuration.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Move the skb_headroom check out of fr_hard_header and into pvc_xmit.
This has two benefits:

1. Originally we only do this check for skbs sent by users on Ethernet-
emulating PVC devices. After the change we do this check for skbs sent on
normal PVC devices, too.
(Also add a comment to make it clear that this is only a protection
against upper layers that don't take dev->needed_headroom into account.
Such upper layers should be rare and I believe they should be fixed.)

2. After the change we can simplify the parameter list of fr_hard_header.
We no longer need to use a pointer to pointers (skb_p) because we no
longer need to replace the skb inside fr_hard_header.

Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The MTU setting for this DSA switch is global so we need
to keep track of the MTU set for each port, then as soon
as any MTU changes, roof the MTU to the biggest common
denominator and poke that into the switch MTU setting.

To achieve this we need a per-chip-variant state container
for the RTL8366RB to use for the RTL8366RB-specific
stuff. Other SMI switches does seem to have per-port
MTU setting capabilities.

Fixes: 5f4a8ef3 ("net: dsa: rtl8366rb: Support setting MTU")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Better place for of_mdio.c is drivers/net/mdio.
Move of_mdio.c from drivers/of to drivers/net/mdio
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When packets are received on the error queue, this function under
net_ratelimit():

netif_err(priv, hw, net_dev, "Err FD status = 0x%08x\n");

does not get printed. Instead we only see:

[ 3658.845592] net_ratelimit: 244 callbacks suppressed
[ 3663.969535] net_ratelimit: 230 callbacks suppressed
[ 3669.085478] net_ratelimit: 228 callbacks suppressed

Enabling NETIF_MSG_HW fixes this issue, and we can see some information
about the frame descriptors of packets.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Factor out handling the private packet/byte counters to new
functions rtl_get_priv_stats() and rtl_inc_priv_stats().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Obviously this driver version doesn't make sense. Go with the default
and let ethtool display the kernel version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Make use of the new struct_size() helper instead of the offsetof() idiom.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-drivers-next-2020-10-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.10

Fourth and last set of patches for v5.10. Most of these are iwlwifi
patches, but few small fixes to other drivers as well.

Major changes:

iwlwifi

* PNVM support (platform-specific phy config data)

* bump the FW API support to 59
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'mac80211-next-for-net-next-2020-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
A handful of changes:
 * fixes for the recent S1G work
 * a docbook build time improvement
 * API to pass beacon rate to lower-level driver
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Johannes Berg says:

====================
netlink: export policy on validation failures

Export the policy used for attribute validation when it fails,
so e.g. for an out-of-range attribute userspace immediately gets
the valid ranges back.

v2 incorporates the suggestion from Jakub to have a function to
estimate the size (netlink_policy_dump_attr_size_estimate()) and
check that it does the right thing on the *normal* policy dumps,
not (just) when calling it from the error scenario.

v3 only addresses a few minor style issues.

v4 fixes up a forgotten 'git add' ... sorry.

v5 is a resend, I messed up v4's cover letter subject (saying v3)
and apparently the second patch didn't go out at all.

Tested using nl80211/iw in a few scenarios, seems to work fine
and return the policy back, e.g.

kernel reports: integer out of range
policy: 04 00 0b 00 0c 00 04 00 01 00 00 00 00 00 00 00
        ^ padding
                    ^ minimum allowed value
policy: 04 00 0b 00 0c 00 05 00 ff ff ff ff 00 00 00 00
        ^ padding
                    ^ maximum allowed value
policy: 08 00 01 00 04 00 00 00
        ^ type 4 == U32

for an out-of-range case.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add a new attribute NLMSGERR_ATTR_POLICY to the extended ACK
to advertise the policy, e.g. if an attribute was out of range,
you'll know the range that's permissible.

Add new NL_SET_ERR_MSG_ATTR_POL() and NL_SET_ERR_MSG_ATTR_POL()
macros to set this, since realistically it's only useful to do
this when the bad attribute (offset) is also returned.

Use it in lib/nlattr.c which practically does all the policy
validation.

v2:
 - add and use netlink_policy_dump_attr_size_estimate()
v3:
 - remove redundant break
v4:
 - really remove redundant break ... sorry
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Refactor the per-attribute policy writing into a new
helper function, to be used later for dumping out the
policy of a rejected attribute.

v2:
 - fix some indentation
v3:
 - change variable order in netlink_policy_dump_write()
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Karsten Graul says:

====================
net/smc: updates 2020-10-07

Patch 1 and 2 address warnings from static code checkers, and patch 3
handles a case when all proposed ISM V2 devices fail to init and no V1
devices are tried afterwards.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Field ini->smcd_version is set to SMC_V2 before calling
smc_listen_ism_init(). This clears the V1 bit that may be set. When all
matching ISM V2 devices fail to initialize then the smcd_version field
needs to get restored to allow any possible V1 devices to initialize.
And be consistent, always go to the not_found label when no device was
found.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

coccinelle informs about
net/smc/af_smc.c:1770:10-11: WARNING: opportunity for kzfree/kvfree_sensitive

Its not that kzfree() would help here, the memset() is done to prepare
the buffer for another socket receive.
Fix that warning message by reordering the calls, while at it eliminate
the unneeded variable cclc2 and use sizeof(*buf) as above in the same
function. No functional changes.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Static code checkers warn of inconsistent returns because the lgr mutex
is locked in one function and unlocked in a function called by the
locking function:
net/smc/af_smc.c:823 smc_connect_rdma() warn: inconsistent returns 'smc_client_lgr_pending'.
net/smc/af_smc.c:897 smc_connect_ism() warn: inconsistent returns 'smc_server_lgr_pending'.

Make the code consistent by doing the unlock in the same function that
fetches the lock. No functional changes.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'linux-can-next-for-5.10-20201007' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
linux-can-next-for-5.10-20201007

The first 3 patches are by me and fix several warnings found
when compiling the  kernel with W=1.

Lukas Bulwahn's patch adjusts the MAINTAINERS file, to accommodate
the renaming of the mcp251xfd driver.

Vincent Mailhol contributes 3 patches for the CAN networking layer.
First error queue support is added the the CAN RAW protocol.
The second patch converts the get_can_dlc() and get_canfd_dlc()
in-Kernel-only macros from using __u8 to u8.
The third patch adds a helper function to calculate the length of
one bit in in multiple of time quanta.

Oliver Hartkopp's patch add support for the ISO 15765-2:2016
transport protocol to the CAN stack.

Three patches by Lad Prabhakar add documentation for various
new rcar controllers to the device tree bindings of the rcar_can
and rcan_canfd driver.

Michael Walle's patch adds various processors to the flexcan
driver binding documentation.

The next two patches are by me and target the flexcan driver aswell.
The remove the ack_grp and ack_bit from the fsl,stop-mode DT property
and the driver, as they are not used anymore. As these are the last
two arguments this change will not break existing device trees.

The last three patches are by Srinivas Neeli and target
the xilinx_can driver.
The first one increases the lower limit for the bit rate
prescaler to 2, the other two fix sparse and coverity findings.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2020-10-07

This series contains updates to ice driver only.

Andy Shevchenko changes usage to %*phD format to print small buffer as hex
string.

Bruce removes repeated words reported by checkpatch.

Ani changes ice_info_get_dsn() to return void as it always returns
success.

Jake adds devlink reporting of fw.app.bundle_id. Moves devlink_port
structure to ice_vsi to resolve issues with cleanup. Adds additional
debug info for firmware updates.

Bixuan Cui resolves -Wpointer-to-int-cast warnings.

Dan adds additional packet type masks and checks to prevent overwriting
existing Flow Director rules.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

A subsequent addition of an IP4 or IP6 rule after other rules would
overwrite any existing TCAM entries of related L4 protocols(ex: tcp4 or
udp6). This was due to the mask including too many TCAM entries. Add new
packet type masks with bits properly excluded so rules are not overwritten.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

pointers should be casted to unsigned long to avoid
-Wpointer-to-int-cast warnings:

drivers/net/ethernet/intel/ice/ice_flow.h:197:33: warning:
    cast from pointer to integer of different size
drivers/net/ethernet/intel/ice/ice_flow.h:198:32: warning:
    cast to pointer from integer of different size
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

While debugging a recent failure to update the flash of an ice device,
I found it helpful to add additional logging which helped determine the
root cause of the problem being a timeout issue.

Add some extra dev_dbg() logging messages which can be enabled using the
dynamic debug facility, including one for ice_aq_wait_for_event that
will use jiffies to capture a rough estimate of how long we waited for
the completion of a firmware command.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, the devlink_port structure is stored within the ice_pf. This
made sense because we create a single devlink_port for each PF. This
setup does not mesh with the abstractions in the driver very well, and
led to a flow where we accidentally call devlink_port_unregister twice
during error cleanup.

In particular, if devlink_port_register or devlink_port_unregister are
called twice, this leads to a kernel panic. This appears to occur during
some possible flows while cleaning up from a failure during driver
probe.

If register_netdev fails, then we will call devlink_port_unregister in
ice_cfg_netdev as it cleans up. Later, we again call
devlink_port_unregister since we assume that we must cleanup the port
that is associated with the PF structure.

This occurs because we cleanup the devlink_port for the main PF even
though it was not allocated. We allocated the port within a per-VSI
function for managing the main netdev, but did not release the port when
cleaning up that VSI, the allocation and destruction are not aligned.

Instead of attempting to manage the devlink_port as part of the PF
structure, manage it as part of the PF VSI. Doing this has advantages,
as we can match the de-allocation of the devlink_port with the
unregister_netdev associated with the main PF VSI.

Moving the port to the VSI is preferable as it paves the way for
handling devlink ports allocated for other purposes such as SR-IOV VFs.

Since we're changing up how we allocate the devlink_port, also change
the indexing. Originally, we indexed the port using the PF id number.
This came from an old goal of sharing a devlink for each physical
function. Managing devlink instances across multiple function drivers is
not workable. Instead, lets set the port number to the logical port
number returned by firmware and set the index using the VSI index
(sometimes referred to as VSI handle).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add "fw.app.bundle_id" to display the DDP Track ID of the active DDP
package. This id is similar to "fw.bundle_id" and is a unique identifier
for the DDP package that is loaded in the device. Each new DDP has
a unique Track ID generated for it, and the ID can be used to identify
and track the DDP package.

Add documentation for the new devlink info version.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ice_info_get_dsn always returns 0, so just make it void.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>