According to hwmon ABI, in%d_enable is a sysfs interface that
allows user space to enable and disable the input sensor. So
this patch just simply adds the attribute to the list.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

When CONFIG_PM_SLEEP is disabled, we get a warning about unused
suspend/resume functions:

drivers/hwmon/ina3221.c:451:12: error: 'ina3221_resume' defined but not used [-Werror=unused-function]
 static int ina3221_resume(struct device *dev)
drivers/hwmon/ina3221.c:428:12: error: 'ina3221_suspend' defined but not used [-Werror=unused-function]
 static int ina3221_suspend(struct device *dev)

Picking the correct #ifdef check is hard, so let's remove
that check and instead mark the functions as __maybe_unused
to let the compiler silently drop them instead.

Fixes: 7de1ab9dac8e ("hwmon: (ina3221) Add suspend and resume functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

An ina3221 chip has three input ports. Each port is used
to measure the voltage and current of its input source.

The DT binding now has defined bindings for their input
sources, so the driver should read these information and
handle accordingly.

This patch adds a new structure of input source specific
information including input source label, shunt resistor
value and its connection status. It exposes these labels
via in[123]_label sysfs nodes upon available, and also
disables those channels where there are no input source
being connected. Meanwhile, it also adds in[123]_enable
sysfs nodes for users to get control of three channels,
and returns -ENODATA code for any sensor read according
to hwmon ABI.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Texas Instruments INA3221 is a triple-channel shunt and bus
voltage monitor. This patch adds a DT binding doc for it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Depending on the hardware design, an INA3221 chip might lose
its power during system suspend/resume. So this patch adds
a set of suspend and resume functions to cache the register
values including config register value and limit settings.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
[groeck: Moved call to dev_set_drvdata()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The three INA3221_CONFIG_MODE macros are not correctly defined here.
The MODE3-1 bits are located at BIT 2-0 according to the datasheet.

So this patch just fixes them by shifting all of them with a correct
offset. However, this isn't a crital bug fix as the driver does not
use any of them at this point.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The MSB (15th bit) of INA3221_CONFIG is a self-clear reset bit.
So this register should be added to the volatile_table of the
regmap_config. Otherwise, we will see this bit is sticky in the
regcache which might accidentally reset the chip when an actual
write happens to the register.

This might not be a severe bug for the current code line since
there's no second place touching the INA3221_CONFIG except the
reset routine in the probe().
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

MAX20751 is a PMBUS driver, which has its own maintainer entry.
On top of that, the entry for MAX20751 points to a non-existing file.
Drop it. Add various missing driver documentation files.
Reported-by: Joe Perches <joe@perches.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Technically this is not required because disabling the PWM should be
enough. However, when support for atomic operations was implemented in
the PWM subsystem, only actual changes to the PWM channel are applied
during pwm_config(), which means that during after resume from suspend
the old settings won't be applied.

One possible solution is for the PWM driver to implement its own PM
operations such that settings from before suspend get applied on resume.
This has the disadvantage of completely ignoring any particular ordering
requirements that PWM user drivers might have, so it is best to leave it
up to the user drivers to apply the settings that they want at the
appropriate time.

Another way to solve this would be to read back the current state of the
PWM at the time of resume. That way, in case the configuration was lost
during suspend, applying the old settings in PWM user drivers would
actually get them applied because they differ from the current settings.
However, not all PWM drivers support reading the hardware state, and not
all hardware may support it.

The best workaround at this point seems to be to let PWM user drivers
tell the PWM subsystem that the PWM is turned off by, in addition to
disabling it, also setting the duty cycle to 0. This causes the resume
operation to apply a configuration that is different from the current
configuration, resulting in the proper state from before suspend getting
restored.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Probe deferrals aren't actual errors, so silence the error message in
case the PWM cannot yet be acquired.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The continue will not truely skip any code. hence it is safe to
remove it.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

NCT6798D is, with the exception of fan and pwm channel configuration
registers, similar to other chips of the series. One interesting
difference is the chip ID, which is now extended to 13 bit (the 12-bit
chip ID value overlaps with the chip ID of NCT6797D).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Add support for NCT6797D. With the exception of fan/pwm configuration
registers, it is mostly compatible with NCT6795D.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

For NCT6795D and NCT6796D, the DIMM temperature sources are named
"Agent[01] Dimm [01]" per datasheet. Match names in datasheets to
avoid confusion.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Now that everything is separated, clean up fan and pwm configuration
for NCT6796D. While doing that, take the forgotten configuration register
cre0 into account to determine if AUXFANIN2 (fan5) and AUXFANOUT2 (pwm5)
are connected.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Separate fan/pwm configuration detection for NCT6795D into separate
case statement to make the code easier to read.

No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

While detecting the configuration for multiple chips in one go reduces
code size, it also increases code complexity. Separate chip detection
to improve code readability. As first step, separate detection for
NCT6793D.

No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Per datasheet, AUXFANIN3 (fan6) and AUXFANOUT3 (pwm6) are only connected
if DSW_EN is false.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

When determining support for a given fan or pwm control, the code is
easier to read if the necessary instructions are grouped together.

No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Use
	boolean |= <expression>;
instead of
	if (!boolean)
		boolean = <expression>;
to assign values to boolean variables.

No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Declare and initialize LDN / chip specific configuration variables
earlier. This simplifies re-using the configuration variables for
multiple chips and makes the code easier to read.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Group configuration variable declarations and initialization together.
While this results in reading more registers than necessary for a given
chip, it improves code readability and simplifies extending the code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Using variables named after configuration registers makes it more obvious
which configuration register value is used, especially if more than one
configuration register value is used to determine a configuration detail.

No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Use variable names from chip datasheets (crXX) instead of regval_XX
for configuration register variables. This is shorter and, together
with subsequent changes, makes the code easier to read.

No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

A fan speed tolerance only makes sense if a fan target speed has been
configured in the first place. Otherwise we get odd output such as

fan1_target:0
fan1_tolerance:337500

Only display values other than 0 if a fan target speed has been configured.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Smatch complains:

drivers/hwmon/lm92.c:209 set_temp_hyst() warn: inconsistent indenting

While at it, fix various other whitespace issues reported by checkpatch
(double empty lines, missing empty lines, whitespace at empty line).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Clang warns when the address of a pointer is used in a boolean context
as it will always return true.

drivers/hwmon/scmi-hwmon.c:59:24: warning: address of array
'sensor->name' will always evaluate to 'true'
[-Wpointer-bool-conversion]
        if (sensor && sensor->name)
                   ~~ ~~~~~~~~^~~~
1 warning generated.

Remove the check as it isn't doing anything currently; if validation
of the contents of the data structure was intended by the original
author (since this line has been present from the first version of
this driver), it can be added in a follow-up patch.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

PTR_ERR_OR_ZERO has implemented the same function. We prefer to use
inlined function rather than code-opened implementation.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

MAX31725/MAX31726 are local temperature sensors with +/- 0.5 degree
Celsius accuracy and 16-bit (0.00390625 degrees Celsius) resolution.
They have a register mapping and encoding compatible with the lm75
series drivers. Address scan and extended temperature range are
not supported by this patch.

Tested on real hardware and verified temperature readings are correct.
Signed-off-by: Kun Yi <kunyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

I removed the "dsw_en &&" chunk of the condition because we know that
"dsw_en" is set.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

BIOS developer guides refer to Family 15h Models 60h-6fh and Family 15h
Models 70h-7fh. So far the driver only checked for Models 60h and 70h.
However, there are now processors with other model numbers in the same
families. Example is A10-9620P family 15h model 65h. Follow the developer
guides and mask the lower 4 bit of the model number to determine the
registers to use for reading temperatures and temperature limits.
Reported-by: Guglielmo Fanini <g.fanini@gmail.com>
Cc: Guglielmo Fanini <g.fanini@gmail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Checking the child node names is pointless as the DT node name can
never be NULL, so remove it.

Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-hwmon@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Calling devm_kstrdup() on a fixed string is unnecessary, as is validating
its contents. Rearrange the code to avoid both.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.

Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Use the nxp.com URLs for the MC13783 and MC13892 datasheets.

The original URLs are still valid, but the nxp.com one is shorter
and more up-to-date.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

'Atlas' was an internal name for the MC13783 PMIC only and does not
apply to MC13892.

To avoid confusion, remove the 'Atlas' term from the description.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

This patch adds support for LTM4686 Ultrathin Dual 10A or
Single 20A uModule Regulator with Digital Power System Management.

Datasheet: http://www.analog.com/ltm4686Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>