From Shawn Guo:
It's the second batch of fixes for 3.8, which includes one fixing for
!CONFIG_SMP build, two patches fixing broken imxfb driver caused by
multiplatform conversion, and a couple of pm/hotplug fixes.

* tag 'imx-fixes-3.8-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: imx: correct low-power mode setting
  ARM: imx: disable cpu in .cpu_kill hook
  video: imxfb: fix imxfb_info configuration order
  ARM: imx: platform-imx-fb: modifies platform device name
  ARM: imx: fix build error with !CONFIG_SMP
Signed-off-by: Olof Johansson <olof@lixom.net>

The hardware reset value of bit CCM_CLPCR_LPM enables WAIT mode
(WAIT_UNCLOCKED) by default.  However this is undesirable because
WAIT mode should only be enabled when there is a driver managing
ARM clock gating.  Correct the initial power mode to WAIT_CLOCKED
(disable WAIT mode).  While at it, the power mode after resuming
is also set back to WAIT_CLOCKED from STOP_POWER_OFF.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

It's buggy to disable the cpu that is being hot-unplugged in .cpu_die
hook which runs on the cpu itself.  Instead, it should be done in
.cpu_kill which runs on the thread (another cpu) that asks for shutting
down the cpu.  Move imx_enable_cpu(cpu, false) call into .cpu_kill
hook, and leave the cpu to be hot-unplugged in WFI within .cpu_die,
so that we can get a more stable cpu hot-plug operation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The devtype field for fbi (struct imxfb_info) must be set after memset call to
avoid some wrong behaviour (pixel size).
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Framebuffer platform device is now identified by a device id (imx1-fb or
imx21-fb) instead of by driver name (imx-fb).
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Some systems compile in both ARMv6 and ARMv7 into multiplatform
configurations. This means the default compiler flags are for ARMv6,
and we will get:

arch/arm/mach-mvebu/coherency_ll.S: Assembler messages:
arch/arm/mach-mvebu/coherency_ll.S:45: Error: selected processor does not support `dsb'

Fix this by specifying ARMv7 flags for coherency_ll.o.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The Integrator/AP syscon remapping was done in the .setup()
function rather than .preinit() which is wrong - .preinit()
is called before .setup() and the former also use the syscon
base and cause a crash since it was not yet remapped.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

From Jason Cooper:
mvebu fixes for v3.8-rc3
 - gpio fixes in mvebu, kirkwood, and dove
 - small DT fix for mvebu (correct RAM size)

* tag 'mvebu_fixes_for_v3.8-rc3' of git://git.infradead.org/users/jcooper/linux:
  arm: mvebu: Fix memory size for Armada 370 DB
  ARM: Dove: add Cubox sdhci card detect gpio
  ARM: Kirkwood: fix ns2 gpios by converting to pinctrl
  arm: mvebu: use global interrupts for GPIOs on Armada XP

Commit 68b25325 (ARM: imx: select HAVE_IMX_SRC when SMP is enabled)
introduces a build error with imx_v6_v7_defconfig when CONFIG_SMP is
deselected.

  LINK    vmlinux
  LD      vmlinux.o
  MODPOST vmlinux.o
  GEN     .version
  CHK     include/generated/compile.h
  UPD     include/generated/compile.h
  CC      init/version.o
  LD      init/built-in.o
arch/arm/mach-imx/built-in.o: In function `imx6q_restart':
platform-ahci-imx.c:(.text+0x448c): undefined reference to `imx_src_prepare_restart'
arch/arm/mach-imx/built-in.o: In function `imx6q_pm_enter':
platform-ahci-imx.c:(.text+0x4544): undefined reference to `imx_set_cpu_jump'
arch/arm/mach-imx/built-in.o: In function `imx6q_init_irq':
platform-ahci-imx.c:(.init.text+0xbef0): undefined reference to `imx_src_init'
make[1]: *** [vmlinux] Error 1

While the commit adds 'def_bool y if SMP' for HAVE_IMX_SRC, it should
not remove 'select HAVE_IMX_SRC' from SOC_IMX6Q, as the IMX6Q UP build
also needs HAVE_IMX_SRC.  Add the HAVE_IMX_SRC select back for SOC_IMX6Q
to fix above build error.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Actually the Armada 370 DB (aka DB-88F6710-BP-DDR3) come with 1GB and
not 512MB.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Card detect for sdhci on Cubox is connected to the wrong pin
(sdio1_cd instead of sdio0_cd). With support for cd-gpios and
pinctrl add the corresponding properties to DT for Cubox.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Note that the pinctrl conversion also fixes GPIO support for ns2 boards.
Since commit f9e75922: "ARM: Kirkwood: Make use of mvebu pincltl and
gpio", the mvbu_gpio driver is used for DT boards. As mvbu_gpio relies
on the pinctrl driver, then a pinctrl definition must be given to allow
the GPIO configuration.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Merge tag 'omap-for-v3.8-rc2/fixes-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

From Tony Lindgren:
The biggest change is a fix to deal with different power state
on omap2 registers that causes issues trying to use common PM code.
Also fix few incorrect registers, and an issue for omap1 USB, and
few sparse fixes for issues that sneaked in with all the clean-up.

* tag 'omap-for-v3.8-rc2/fixes-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
  ARM: OMAP1: fix USB configuration use-after-release
  ARM: OMAP2/3: PRM: fix bogus OMAP2xxx powerstate return values
  ARM: OMAP3: clock data: Add missing enable/disable for EMU clock
  ARM: OMAP4: PRM: Correct wrong instance usage for reading reset sources
  ARM: OMAP4: PRM: fix RSTTIME and RSTST offsets
  ARM: OMAP4: PRM: Correct reset source map
  ARM: OMAP: SRAM: resolve sparse warnings
  ARM: OMAP AM33xx: hwmod data: resolve sparse warnings
  ARM: OMAP: 32k counter: resolve sparse warnings
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge branch 'v3.8-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

From Kukjin Kim:
Most of them are EXYNOS5440 fixes which are for changing uart console,
cpu id (typo)  and silent complaining gpio error in kernel boot.

* 'v3.8-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: skip the clock initialization for exynos5440
  ARM: EXYNOS: enable PINCTRL for EXYNOS5440
  ARM: dts: use uart port1 for console on exynos4210-smdkv310
  ARM: dts: use uart port0 for console on exynos5440-ssdk5440
  ARM: SAMSUNG: fix the cpu id for EXYNOS5440
  ARM: EXYNOS: Revise HDMI resource size

From Shawn Guo:
I have to send one critical mxsfb fix through arm-soc, as FB maintainer
is unresponsive for quite a while.  People start complaining the missing
of such an important fix.

* tag 'mxs-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
  video: mxsfb: fix crash when unblanking the display
  ARM: dts: imx23-olinuxino: Fix IOMUX settings

From Shawn Guo:

It includes one critical fix - wrong flexcan2 clock will hang system
when the port gets brought up.  The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.

* tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: mx5: Fix MX53 flexcan2 clock
  ARM: dts: imx31-bug: Fix manufacturer compatible string
  clk: imx: Remove 'clock-output-names' from the examples

The Armada XP GPIO controller has two ways of notifying interrupts:
using global interrupts or using per-CPU interrupts. In an attempt to
use the best available features, the 'marvell,armadaxp-gpio'
compatible string selects a variant of the gpio-mvebu driver that
makes use of the per-CPU interrupts.

Unfortunately, this doesn't work properly in a SMP context, because we
fall into cases where the GPIO interrupt is enabled on CPU X at the
GPIO controller level, but on CPU Y at the interrupt controller
level. It is not yet clear how to fix that easily.

So for 3.8, our approach is to switch to global interrupts for GPIOs,
so that we do not fall into this per-CPU interrupts problem.

This patch therefore fixes GPIO interrupts on Armada XP
platforms. Without this patch, GPIO interrupts simply do not work
reliably, because their proper operation depends on which CPU the code
requesting the interrupt is running.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

From Jason Cooper:

fixes for mvebu/kirkwood v3.8
 - use correct uart driver for mvebu boards
 - add a missing DT clocks
 - gpio-poweroff level vs. edge triggering, use gpio_is_valid()
 - remove an inappropriate __init, modules need to access function.
 - various DT fixes
 - error handling in mv_xor

* tag 'mvebu_fixes_for_v3.8' of git://git.infradead.org/users/jcooper/linux:
  pinctrl: mvebu: make pdma clock on dove mandatory
  ARM: Dove: Add pinctrl clock to DT
  dma: mv_xor: fix error handling for clocks
  dma: mv_xor: fix error handling of mv_xor_channel_add()
  arm: mvebu: Add missing ; for cpu node.
  arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
  arm: mvebu: Armada XP MV78230 has two cores, not one
  clk: mvebu: Remove inappropriate __init tagging
  ARM: Kirkwood: Use fixed-regulator instead of board gpio call
  ARM: Kirkwood: Fix missing sdio clock
  ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
  Power: gpio-poweroff: Fix documentation and gpio_is_valid
  ARM: Kirkwood: Fix missing clk for USB device.
  arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
Signed-off-by: Olof Johansson <olof@lixom.net>

I mismerged a previous branch from Alexander, and accidentally left
in ARCH_USES_GETTIMEOFFSET. Remove it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Alexander Shiyan <shc_work@mail.ru>

Merge tag 'nomadik-fixes-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into fixes

From Linus Walleij:
Two fixes to the Nomadik:
- Delete a dangling include
- Bump IRQ numbers to offset at 32

* tag 'nomadik-fixes-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
  ARM: nomadik: bump the IRQ numbers again
  ARM: nomadik: delete dangling include

This fixes suspend to RAM adding necessary save and restore of L2 and GIC.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

When we fail to power down, we need to clear out the power request.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

With commit 384a2902 (ARM: gic: use a private mapping for CPU target
interfaces), wake-up IPIs now go to all cores as the gic cpu interface
numbering may not follow core numbering. This broke secondary boot on
highbank since the boot address was already set for all secondary cores,
this caused all cores to boot before the kernel was ready.

Fix this by moving the setting of the jump address to
highbank_boot_secondary instead of highbank_smp_prepare_cpus and
highbank_cpu_die. Also, clear the address when we boot. This prevents
cores from booting before they are actually triggered and is also necessary
to get suspend/resume to work.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

s/hignbank/highbank/
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

With the addition of commit a0ae0240 (ARM: kernel: add device tree init
map function), the cpu reg values must match the cpu mpidr register or we'll
get warnings. For some reason, the CLUSTERID on highbank is 9, so the reg
value needs to be 0x90n to quiet the warnings.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

While device_type is considered deprecated, it is still needed for tools
like lshw to identify cpu nodes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The second FlexCAN port uses different clock than the first one, configure
correct clock to prevent hanging of the system during bringing up of the port.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The IRQ array must be terminated by -1 and not by -1+OMAP_INTC_START
This led to having a resource list of 100s of IRQs.

Looks like this was caused by commit a2cfc509 (ARM: OMAP3+: hwmod: Add
AM33XX HWMOD data) that probably had some search and replace updates
done for the patch for sparse irq support.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated wit information about the breaking commit]
Signed-off-by: Tony Lindgren <tony@atomide.com>

With the ability to pass clocks through DT, now make the pdma
clock of dove pinctrl mandatory. Otherwise, pinctrl will hang
the system when accessing some registers.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

During merge of the mvebu patches a clock gate for pinctrl was
lost. This patch just readds the clock gate.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

When a channel fails to initialize, we release all ressources,
including clocks. However, a XOR unit is not necessarily associated to
a clock (some variants of Marvell SoCs have a clock for XOR units,
some don't), so we shouldn't unconditionally be releasing the clock.

Instead, just like we do in the mv_xor_remove() function, we should
check if one clock was found before releasing it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

When mv_xor_channel_add() fails for one XOR channel, we jump to the
err_channel_add label to clean up all previous channels that had been
initialized correctly. Unfortunately, while handling this error
condition, we were disposing the IRQ mapping before calling
mv_xor_channel_remove() (which does the free_irq()), which is
incorrect.

Instead, do things properly in the reverse order of the
initialization: first remove the XOR channel (so that free_irq() is
done), and then dispose the IRQ mapping.

This avoids ugly warnings when for some reason one of the XOR channel
fails to initialize.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Armada XP MV78230 DT include file is missing a ; at the
end of the cpu node.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

We originally thought that the MV78230 variant of the Armada XP had
four Ethernet interfaces, like the other variants MV78260 and
MV78460. In fact, this is not true, and the MV78230 has only three
Ethernet interfaces.

So, the definitions of the Ethernet interfaces is now done as follows:

 * armada-370-xp.dtsi: definitions of the first two interfaces, that
   are common to Armada 370 and Armada XP

 * armada-xp.dtsi: definition of the third interface, common to all
   Armada XP variants.

 * armada-xp-mv78260.dtsi and armada-xp-mv78460.dtsi: definition of
   the fourth interface.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Contrary to our understanding at the time armada-xp-mv78230.dtsi was
written, the MV78230 variant of the Armada XP SoC has two cores and
not one. This patch updates the .dtsi file to take into account this
reality.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

If the Orion WDT driver is built as a module, an opps occurs during
clk lookup when calling mvebu_clk_gating_get_src().  Remove the
inappropriate __init tag so the function is available for modules
after kernel init.
Signed-off-by: Joshua Coombs <josh.coombs@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

With the change to a DT based pinctrl/gpio driver, using gpio API
calls in board-*.c files no longer works, a dereferenced NULL pointer
exception occurs instead. By converting the GPIO code into a
fixed-regulator which gets probed later once pinctrl/gpio is
available, we avoid the exception.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mplch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

We moved to declaring clk gates in DT. However, device which do not
yet have a DT binding need to have a clkdev alias. This was missing
for SDIO.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mplch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Clock Management of kirkwood has moved to DT clock providers.
However, TWSI1 has not yet been done.
This switches TWSI1 of 88f6282 to DT clock providers.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Improve the documentation to clarify level vs edge triggered power off.
Improve the comments for level vs edge triggered power off.
Make use of gpio_is_valid().
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>