- 17 Mar, 2012 3 commits
-
-
Stefan Roese authored
This patch adds support to configure the STMMAC ethernet driver via device-tree instead of platform_data. Currently, only the properties needed on SPEAr600 are provided. All other properties should be added once needed on other platforms. Signed-off-by:
Stefan Roese <sr@denx.de> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Santosh Nayak authored
Change the datatype of "ip_addr" to __be32 as 'ip' should be in big endian format. Adapter needs "ip address" in big endian format stored at lower 32bit of req.word[1]. netxen_config_ipaddr() now receives 'ip' in big endian format. To satisfy adapter's need, use memcpy() to copy byte by byte of 'ip' into lower 32bit of req.word[1]. Mac address and serial number of adapter need to be in little endian format. Change the data type of the related variables to __le32 / __le64 or cast it explicitly to __le32 / __le64 depending upon the requirement. Signed-off-by:
Santosh Nayak <santoshprasadnayak@gmail.com> Signed-off-by:
-
Rami Rosen authored
The patch removes unused stats member in pxa168 network driver. Signed-off-by:
Rami Rosen <ramirose@gmail.com> Signed-off-by:
-
- 16 Mar, 2012 5 commits
-
-
John W. Linville authored
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem Conflicts: drivers/net/wireless/ath/ath9k/hw.c
-
Alexey Orishko authored
Changes: - removed a limit for amount of datagrams for IN NTB - using pointer to traverse NTB in rx_fixup() - renamed "temp" to "len" in rx_fixup() - do NTB sequence number check in rx path Tested on Intel/ARM. Reviewed-by:
Sjur Brændeland <sjur.brandeland@stericsson.com> Tested-by:
Dmitry Tarnyagin <Dmitry.Tarnyagin@stericsson.com> Signed-off-by:
Alexey Orishko <alexey.orishko@stericsson.com> Signed-off-by:
-
Alexey Orishko authored
Changes/fixes: - inform device if max_datagram_size was changed by host - max_datagram_size can't be bigger MTU in ETH func descr - fix constants definitions to enable running CAIF service over NCM Tested on Intel/ARM. Reviewed-by:
-
Alexey Orishko authored
Changes: - use high resolution timer latency became approx. 10-15 times less than before - use taklet for sending remaining data in tx path Tested on Intel/ARM. Reviewed-by:
-
Eric Dumazet authored
asix_rx_fixup() is complex, and does some unnecessary memory copies (at least on x86 where NET_IP_ALIGN is 0) Also, it tends to provide skbs with a big truesize (4096+256 with MTU=1500) to upper stack, so incoming trafic consume a lot of memory and I noticed early packet drops because we hit socket rcvbuf too fast. Switch to a different strategy, using copybreak so that we provide nice skbs to upper stack (including the NET_SKB_PAD to avoid future head reallocations in some paths) With this patch, I no longer see packets drops or tcp collapses on various tcp workload with a AX88772 adapter. Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> Cc: Aurelien Jacobs <aurel@gnuage.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Trond Wuellner <trond@chromium.org> Cc: Grant Grundler <grundler@chromium.org> Cc: Paul Stewart <pstew@chromium.org> Reviewed-by:
Grant Grundler <grundler@chromium.org> Reviewed-by:
-
- 15 Mar, 2012 31 commits
-
-
-
Daniel Drake authored
libertas provides a dump_survey implementation based on reading of a RSSI value. However, this RSSI value is calculated based on the last received beacon from the associated AP - it is not a good way of surveying a channel in general, and even causes an error if the card is not associated to a network. As this is not appropriate as a survey, remove it. This fixes an issue where something in userspace is repeatedly calling site-survey during boot, resulting in many repeated errors as the RSSI value cannot be read before associating. Signed-off-by:
Daniel Drake <dsd@laptop.org> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Felix Fietkau authored
Makes them more readable and reduces code size Signed-off-by:
-
Felix Fietkau authored
Program tx gain through iniModesTxGain like on AR9287 Signed-off-by:
-
Felix Fietkau authored
use iniModesFastClock for 5 ghz fast clock specific settings, and iniAdditional for clock/chip specific initval overrides Signed-off-by:
-
Felix Fietkau authored
Program the ah->ini_japan2484 INI values which were left out by accident Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
These arrays are unused Signed-off-by:
-
Felix Fietkau authored
The ATH9K_HW_CAP_AUTOSLEEP check is bogus, the rx status area needs to be cleared on all non-EDMA PCI/AHB based chipsets anyway. Limit the memset to the rx status area to improve performance. Signed-off-by:
-
Felix Fietkau authored
The driver can just check the mask directly Signed-off-by:
-
Felix Fietkau authored
By checking for NR_CPUS, the compiler can optimize out register access serialization code on non-SMP kernels Signed-off-by:
-
Felix Fietkau authored
The default antenna (as programmed by the INI file) is always 0 anyway. Signed-off-by:
-
Felix Fietkau authored
Automatically set the ah->htc_reset_init on init and after PHY disable. Signed-off-by:
-
Felix Fietkau authored
TXQ_FLAG_TXOKINT_ENABLE and TXQ_FLAG_TXERRINT_ENABLE are always set and used together, and they share the same bitmask in enum ath9k_tx_queue_flags. Simplify the code that tests for these flags. Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Eliad Peller authored
uapsd_queues and uapsd_max_sp_len are relevant only for managed interfaces, and can be configured differently for each vif. Move them from the local struct to sdata->u.mgd, and update the debugfs functions accordingly. Signed-off-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
-
Eliad Peller authored
Some debugfs write functions call kstrto* functions, which assume the string is null-terminated. Make it valid by changing ieee80211_if_write() to use static buffer instead of allocating one, and set the last char to NULL. (The write functions try to parse some integer/mac address, so 64 bytes buffer should be enough) Signed-off-by:
-
Helmut Schaa authored
The current max throughput rate is known to be good as otherwise it wouldn't be the max throughput rate. Since rate sampling can introduce some overhead (by adding RTS for example or due to not aggregating the frame) don't sample the max throughput rate. Signed-off-by:
Helmut Schaa <helmut.schaa@googlemail.com> Acked-by:
-
Stanislaw Gruszka authored
TX status fifo is limited to 16 elements. When we send more frames than that, we can easily loose status, what is not good for rate scaling algorithm. On my testing the change does not degrade performance, actually make is slightly better. Additionally with the patch I can see much less various rt2x00 warnings in dmesg. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Acked-by:
-
Stanislaw Gruszka authored
Tx statuses of aggregated subframes contain packetid of first subframe in the AMPDU. We can not identify AMPDU subframes based on packedid, so simply assume that status match first pending frame in the queue. Thats mostly the same what 2800pci do. Signed-off-by:
-
Stanislaw Gruszka authored
Currently we read tx status register after each urb data transfer. As callback procedure also trigger reading, that causing we have many "threads" of reading status. To prevent that introduce TX_STATUS_READING flags, and check if we are already in process of sequential reading TX_STA_FIFO, before requesting new reads. Change timer to hrtimer, that make TX_STA_FIFO overruns less possible. Use 200 us for initial timeout, and then reschedule in 100 us period, this values probably have to be tuned. Make changes on txdone work. Schedule it from rt2800usb_tx_sta_fifo_read_completed() callback when first valid status show up. Check in callback if tx status timeout happens, and schedule work on that condition too. That make possible to remove tx status timeout from generic watchdog. I moved that to rt2800usb. Loop in txdone work, that should prevent situation when we queue work, which is already processed, and after finish work is not rescheduled again. Signed-off-by:
-
Stanislaw Gruszka authored
Patch change txdone code to make it similar like txdone in rt2800pci, process only one entry from queue matching tx status. Before we processed all pending entries from queue until PACKEDID match, that caused that we do not report tx statuses correctly. Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Sujith Manoharan authored
mac80211 provides short preamble information and ERP protection information on a per-BSS basis, which can be used. Remove flags stored in the driver, which was incorrect since they were being used in a global manner. Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Sujith Manoharan authored
SC_OP_TXAGGR and SC_OP_RXAGGR are not really needed. The HT capabilities of the station and HW can be used instead. Signed-off-by:
-
Sujith Manoharan authored
The logic to determine whether to use FCC is a bit convoluted. Use a small helper function to decide whether FCC is to be used. Signed-off-by:
-
Sujith Manoharan authored
It is not needed and will not be used anyway since unsupported interfaces are not allowed to be created. Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
There is no need to mask out SWBA/BMISS from the interrupt mask in start(). Signed-off-by:
-
Helmut Schaa authored
rt2800 already reports the tx ack status of each frame back to mac80211. Advertise this by setting IEEE80211_HW_REPORTS_TX_ACK_STATUS for rt2800. This allows some mac80211 features like frame loss notifications to work with rt2800. Signed-off-by:
-
- 14 Mar, 2012 1 commit
-
-
Amitkumar Karwar authored
"hscfg" is declared as struct mwifiex_ds_hs_cfg. Use same structure name for calculating it's size. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
