Add support for these two new cards.

Based upon Devin's initial patch made for an older kernel which I
cleaned up and rebased. Thanks to Kernel Labs for that work.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add simple support for this 8 channel volume control driver.
Currently all it does is to unmute all 8 channels.

Based upon Devin's initial patch made for an older kernel which I
cleaned up and rebased. Thanks to Kernel Labs for that work.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This is necessary since the *_std_setup functions rely on a valid state->std
field.

Also fix the cx23888_std_setup() to test for 60Hz instead of NTSC, just like
cx25840_std_setup() does.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

For those two devices the code wrote to addresses 0x115/6, but on
those devices those addresses have nothing to do with power controls.
So clearly this never worked. Rather than writing to bogus addresses,
just do nothing for the cx2388x and cx231xx.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The cx23888 reports a slightly different Vsrc value than the other
chip variants do. Relax the check by 1, otherwise cx25840_set_fmt()
would fail for the cx23888.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The cx23888 also moves the following registers around:

!cx23888	cx23888
--------	-------
0x418, 0x41c	0x434, 0x438
0x420		0x418 (expect for bit 29 which has a different meaning)
0x478		0x454

Also drop the set_input code where the scaler is changed: this does not
belong here, changing the input should not change the scaler.

And that's besides the fact that that code is plain wrong.

After this change the cx23888 behaves much better. In particular, calling
set_input no longer changes the saturation to 0, causing a grayscale
image.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The cx23888 has the VBI registers at different addresses compared to
the other variants. In most cases it is a fixed offset, but not always.

Update the code so the right registers are written for the cx23888.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

These two drivers reported the pixel aspect ratio the wrong way around.
This caused qv4l2 to scale the image incorrectly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The pixelaspect ratio was set incorrectly for 60Hz formats.
And since cropcap wasn't implemented at all for the -417 (compressed
video) the pixelaspect was unknown for compressed video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

While testing the cx23885 driver with various TV standards I found
a number of bugs:

1) norm_maxw() returned 768 instead of 720 for PAL formats. This should
   always be 720, so drop this inline function and just always use 720.
2) cropcap() was missing, so the pixelaspect was never known and qv4l2 would
   scale the image incorrectly. Add cropcap support.
3) cx23885_set_tvnorm() should just return 0 if the same standard was
   set again. If another standard is set, then reset the width/height and
   call set_fmt for the subdevs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This reverts commit 120c41d3.

The patch doesn't add the corresponding documentation bits to the
media infrastructure uAPI DocBook. Also, they're for 3D formats,
with requre further discussions.
Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Requested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

While https was always supported on linuxtv.org, only in
Dec 3 2015 the website is using valid certificates.

As we're planning to drop pure http support on some
future, change all references at the media subsystem
to point to the https URL instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

While https was always supported on linuxtv.org, only in
Dec 3 2015 the website is using valid certificates.

As we're planning to drop pure http support on some
future, change the references at DRM include and at
the ipu-v3 driver to point to the https://linuxtv.org
URL instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

While https was always supported on linuxtv.org, only in
Dec 3 2015 the website is using valid certificates.

As we're planning to drop pure http support on some
future, change the http://linuxtv.org references at firmware/WHENCE
file to point to https://linuxtv.org instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

While https was always supported on linuxtv.org, only in
Dec 3 2015 the website is using valid certificates.

As we're planning to drop pure http support on some
future, change all references at MAINTAINERS file
to point to the https URL instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

'struct timeval tv' and 'struct timeval now' is used to calculate the
elapsed time. 'LIRC_SFH506_DELAY' is a delay t_phl in usecs.

32-bit systems using 'struct timeval' will break in the year 2038,
so we have to replace that code with more appropriate types.
This patch changes the lirc_parallel.c file of  media: lirc driver
to use ktime_t.

ktime_get() is  better than using do_gettimeofday(),
because it uses the monotonic clock. ktime_sub is used
to subtract two ktime variables. ktime_to_us() is used to
convert ktime to microsecond.

New ktime_t variable timeout, is added in lirc_off(),to improve
clarity. Introduced a new ktime_t variable in lirc_lirc_irq_handler()
function, to avoid the use of signal variable for storing
seconds in the first part of this function as later it uses
a time unit that is defined by the global "timer" variable.
This makes it more clear.

ktime_set() is used to set a value in seconds to a value in
nanosecond so that ktime_compare() can be used appropriately.
ktime_compare() is used to compare two ktime values.
ktime_add_ns() is used to increment a ktime value by 1 sec.

One comment is also shifted a line up, as it was creating a 80
character warning.

Build tested it. Also tested it with sparse.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

'struct timeval presstime' and 'struct timeval tv' is used to
calculate the time since the last button press.

32-bit systems using 'struct timeval' will break in the year 2038,
so we have to replace that code with more appropriate types.
This patch changes the media: lirc driver to use ktime_t.

ktime_get() is  better than using do_gettimeofday(), because it uses
the monotonic clock. ktime_sub() are used to subtract two ktime
variables. 'ms' is only used to check how much time has passed by comparing
to 250. So instead of using expensive ktime_to_ms() call, it has been
changed to hold nanoseconds by using ktime_to_ns().

Build tested it. Tested with sparse too.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

'struct timeval tv' is used to get current time.
'static struct timeval lasttv' is used to get last interrupt time.

32-bit systems using 'struct timeval' will break in the year 2038,
so we have to replace that code with more appropriate types.
This patch changes the lirc_serial.c file of media: lirc to use
ktime_t.

ktime_get() is  better than using do_gettimeofday(),
because it uses the monotonic clock. ktime_sub is used
to subtract two ktime variables. The check to test time
going backwards is also removed. Intialization to static
variable is also removed. ktime_to_us() is used to convert
ktime_t to microsecond value. deltv is changed to delkt, a
ktime_t type varibale from long to assign the ktime_sub value
directly. ktime_compare is used to compare delkt with 15
seconds, which is changed to a nanosecond value by using
ktime_set().

Build tested it.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Fixes a warning message found by checkpatch.pl WARNING:
	suspect code indent for conditional statements
Signed-off-by: Joseph Marrero <jmarrero@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Without I get this error for by dvb-card:
  tda10071: Unknown symbol devm_regmap_init_i2c (err 0)
  cx23885_dvb_register() dvb_register failed err = -22
  cx23885_dev_setup() Failed to register dvb adapters on VID_B
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.

Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
 free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Now that that the decoder modules are loaded on-demand we can move
loading the lirc module to rc_register_device directly and remove
unneeded functions and comments.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

It works only for HVR-4400/HVR-5500.
For WinTV-HVR-930C-HD it fails with bad/no reception
for unknown reasons.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The current si2165_set_frontend() function actually works only for DVB-T.
Split it into two functions, preparing the code to support DVB-C.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Use si2165_write_reg_list() to do the DVB-T mode initialization altogether.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

si2165_set_if_freq_shift() needs to call get_if_frequency() in order to do
the right shift. Add such logic inside the function, simplifying the logic
for the callers.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The TS config is fixed, so no need to write it for each tune.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Datasheet says they must be rewritten after reset.
But it only makes sense to write them when trying to tune afterwards.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

It is common the need of writing a table of values. Add a function to provide a
helper to address such case. This will allow further code cleanups.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

No functional changes.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

No functional changes.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add support for Intel DS4 depth camera in uvc driver.
This includes adding new uvc GUIDs for the new pixel formats,
adding new V4L pixel format definition to user api headers,
and updating the uvc driver GUID-to-4cc tables with the new formats.

Change-Id: If240d95a7d4edc8dcc3e02d58cd8267a6bbf6fcb
Tested-by: Greenberg, Aviv D <aviv.d.greenberg@intel.com>
Signed-off-by: Aviv Greenberg <aviv.d.greenberg@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The cx2341x_handler_ops structures are never modified, so declare them as
const.

Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The snd_tea575x_ops structures are never modified, so declare them as
const.

Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add the new match_reduced_fps argument to v4l2_match_dv_timings().
Depending on the situation you may or may not desire to match the
reduced_fps flag. Typically only HDMI transmitters will need to
check for this flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Linux 4.4-rc2

Several PCI media drivers got broken on Kernel 4.4-rc1, due to
pci_set_dma_mask() regressions. So, we need to add those fixes back
for the media drivers to work again.

* tag 'v4.4-rc2': (335 commits)
  Linux 4.4-rc2
  slab/slub: adjust kmem_cache_alloc_bulk API
  slub: add missing kmem cgroup support to kmem_cache_free_bulk
  slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
  slub: optimize bulk slowpath free by detached freelist
  slub: support for bulk free with SLUB freelists
  parisc: Map kernel text and data on huge pages
  parisc: Add Huge Page and HUGETLBFS support
  parisc: Use long branch to do_syscall_trace_exit
  parisc: Increase initial kernel mapping to 32MB on 64bit kernel
  parisc: Initialize the fault vector earlier in the boot process.
  parisc: Add defines for Huge page support
  parisc: Drop unused MADV_xxxK_PAGES flags from asm/mman.h
  serial: export fsl8250_handle_irq
  serial: 8250_mid: Add missing dependency
  tty: audit: Fix audit source
  serial: etraxfs-uart: Fix crash
  serial: fsl_lpuart: Fix earlycon support
  bcm63xx_uart: Use the device name when registering an interrupt
  tty: Fix direct use of tty buffer work
  ...

Merge slub bulk allocator updates from Andrew Morton:
 "This missed the merge window because I was waiting for some repairs to
  come in.  Nothing actually uses the bulk allocator yet and the changes
  to other code paths are pretty small.  And the net guys are waiting
  for this so they can start merging the client code"

More comments from Jesper Dangaard Brouer:
 "The kmem_cache_alloc_bulk() call, in mm/slub.c, were included in
  previous kernel.  The present version contains a bug.  Vladimir
  Davydov noticed it contained a bug, when kernel is compiled with
  CONFIG_MEMCG_KMEM (see commit 03ec0ed5: "slub: fix kmem cgroup
  bug in kmem_cache_alloc_bulk").  Plus the mem cgroup counterpart in
  kmem_cache_free_bulk() were missing (see commit 03374518 "slub:
  add missing kmem cgroup support to kmem_cache_free_bulk").

  I don't consider the fix stable-material because there are no in-tree
  users of the API.

  But with known bugs (for memcg) I cannot start using the API in the
  net-tree"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  slab/slub: adjust kmem_cache_alloc_bulk API
  slub: add missing kmem cgroup support to kmem_cache_free_bulk
  slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
  slub: optimize bulk slowpath free by detached freelist
  slub: support for bulk free with SLUB freelists

Pull tty/serial fixes from Greg KH:
 "Here are a few small tty/serial driver fixes for 4.4-rc2 that resolve
  some reported problems.

  All have been in linux-next, full details are in the shortlog below"

* tag 'tty-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: export fsl8250_handle_irq
  serial: 8250_mid: Add missing dependency
  tty: audit: Fix audit source
  serial: etraxfs-uart: Fix crash
  serial: fsl_lpuart: Fix earlycon support
  bcm63xx_uart: Use the device name when registering an interrupt
  tty: Fix direct use of tty buffer work
  tty: Fix tty_send_xchar() lock order inversion

Pull staging/IIO fixes from Greg KH:
 "Here are some staging and iio driver fixes for 4.4-rc2.  All of these
  are in response to issues that have been reported and have been in
  linux-next for a while"

* tag 'staging-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Revert "Staging: wilc1000: coreconfigurator: Drop unneeded wrapper functions"
  iio: adc: xilinx: Fix VREFN scale
  iio: si7020: Swap data byte order
  iio: adc: vf610_adc: Fix division by zero error
  iio:ad7793: Fix ad7785 product ID
  iio: ad5064: Fix ad5629/ad5669 shift
  iio:ad5064: Make sure ad5064_i2c_write() returns 0 on success
  iio: lpc32xx_adc: fix warnings caused by enabling unprepared clock
  staging: iio: select IRQ_WORK for IIO_DUMMY_EVGEN
  vf610_adc: Fix internal temperature calculation