This kind of hacks disturbs the refactoring of the gpiolib.

The descriptor table belongs to the gpiolib, if we want to know
something about something in it, use or define the proper accessor
functions. Let's add this gpiochip_lins_is_irq() to do what the
sunxi driver is trying at so we can privatize the descriptors
properly.

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We need gpio_device to hold the descriptors so that they can
be lifecycled with the struct gpio_device held from userspace.
Move the descriptor array into gpio_device. Also rename it from
"desc" (singularis) to "descs" (pluralis) to reflect the fact
that it is an array.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Since gpio_device is the struct that survives if the backing
gpio_chip is removed, move the sysfs mock device to this state
container so it becomes part of the dangling state of the
GPIO device on removal.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

When the device core reference count for the device goes to
0 and it calls .release() we free resources and so can also
finally free up the GPIO state container, struct gpio_device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Driver for the GPIO block found in ti's tps65218 pmics.

The device has two GPIOs and one GPO pin which can be configured as follows:
GPIO1:
	-general-purpose, open-drain output controlled by GPO1 user bit and/or
	 sequencer
	-DDR3 reset input signal from SOC. Signal is either latched or
	 passed-trough to GPO2 pin. See below for details.
GPO2:
	-general-purpose output controlled by GPO2 user bit
	-DDR3 reset output signal. Signal is controlled by GPIO1 and PGOOD.
	 See below for details.
	-Output buffer can be configured as open-drain or push-pull.
GPIO3:
	-general-purpose, open-drain output controlled by GPO3 user bit and/or
	 sequencer
	-reset input-signal for DCDC1 and DCDC2.

The input configurations are not meant to be used by the user so the driver
only offers GPOs.

v2: Added request routine that evaluates the fw config flags and removed module
    owner
v3: Added .direction_input() routine, and took care of all Linus Walleij
suggestions (clamp to bool, use proper include)
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add driver for TI TPIC2810 8-Bit LED Driver with I2C Interface.

The TPIC2810 has 8 open-drain outputs that can but used to drive
LEDs and other low-side switched resistive loads.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add generic parallel-in/serial-out shift register GPIO driver.

This includes SPI compatible devices like SN74165 serial-out shift
registers and the SN65HVS88x series of industrial serializers that can
be read over the SPI bus and used for GPI (General Purpose Input).
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add myself to the copyright list and remove the reference to Atheros'
BSP as nothing is left of this code.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add support for the interrupt controller using GPIOLIB_IRQCHIP.
Both edges isn't supported by the chip and has to be emulated
by switching the polarity on each interrupt.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

As we now allow the driver to be built as a module it should be
removable.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

To allow building the driver in compile tests we must drop the
dependency on asm/mach-ath79/ar71xx_regs.h. For this we replace the
include with local definition of the registers needed for this driver.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Drop most of the code in favor of the generic MMIO GPIO driver.
As the driver now depend on CONFIG_GPIO_GENERIC also add a Kconfig
entry to make the driver optional.

We leave the base pointer and lock in the data struct because they are
needed for the IRQ support.
Signed-off-by: Alban Bedel <albeu@free.fr>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This marks the (optional) sysfs GPIO ABI as obsolete and schedules
it for removal in 2020.

Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Put in some documentation for the new character device ABI
so we can properly etch it in stone.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This creates GPIO tools under tools/gpio/* and adds a single
example program to list the GPIOs on a system. When proper
devices are created it provides this minimal output:

Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

A new chardev that is to be used for userspace GPIO access is
added in this patch. It is intended to gradually replace the
horribly broken sysfs ABI.

Using a chardev has many upsides:

- All operations are per-gpiochip, which is the actual
  device underlying the GPIOs, making us tie in to the
  kernel device model properly.

- Hotpluggable GPIO controllers can come and go, as this
  kind of problem has been know to userspace for character
  devices since ages, and if a gpiochip handle is held in
  userspace we know we will break something, whereas the
  sysfs is stateless.

- The one-value-per-file rule of sysfs is really hard to
  maintain when you want to twist more than one knob at a time,
  for example have in-kernel APIs to switch several GPIO
  lines at the same time, and this will be possible to do
  with a single ioctl() from userspace, saving a lot of
  context switching.

We also need to add a new bus type for GPIO. This is
necessary for example for userspace coldplug, where sysfs is
traversed to find the boot-time device nodes and create the
character devices in /dev.

This new chardev ABI is *non* *optional* and can be counted
on to be present in the future, emphasizing the preference
of this ABI.

The ABI only implements one single ioctl() to get the name
and number of GPIO lines of a chip. Even this is debatable:
see it as a minimal example for review. This ABI shall be
ruthlessly reviewed and etched in stone.

The old /sys/class/gpio is still optional to compile in,
but will be deprecated.

Unique device IDs are created using IDR, which is overkill
and insanely scalable, but also well tested.

Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We use the new struct device inside gpio_chip to related debug
prints and warnings, and we also add it to the debugfs dump.

Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

GPIO chips have been around for years, but were never real devices,
instead they were piggy-backing on a parent device (such as a
platform_device or amba_device) but this was always optional.
GPIO chips could also exist without any device at all, with its
struct device *parent (ex *dev) pointer being set to null.

When sysfs was in use, a mock device would be created, with the
optional parent assigned, or just floating orphaned with NULL
as parent.

If sysfs is active, it will use this device as parent.

We now create a gpio_device struct containing a real
struct device and move the subsystem over to using that. The
list of struct gpio_chip:s is augmented to hold struct
gpio_device:s and we find gpio_chips:s by first looking up
the struct gpio_device.

The struct gpio_device is designed to stay around even if the
gpio_chip is removed, so as to satisfy users in userspace
that need a backing data structure to hold the state of the
session initiated with e.g. a character device even if there is
no physical chip anymore.

From this point on, gpiochips are devices.

Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The new Layerscape platforms has the same ip block/controller
as GPIO on PowerPC platforms(MPC8XXX), but the GPIO registers
may be big or little endian. So the code needs to get the
endian property from DTB, then make additional functions to
fit all the PowerPC/Layerscape GPIO register read/write
operations.

gpio-generic.c provides an universal infrastructure for both
big and little endian register operations. So switch the
gpio-mpc8xxx to use gpio-generic can simplify the driver and
reduce a lot of code.

The IRQ and some workaround parts in gpio-mpc8xxx.c will be
updated with the new API interfaces but following the
original functionalities.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The TS-4800 GPIO driver provide support for the GPIOs available
on the Technologic Sytems board FPGA. It allows to set
direction and read/write states.

It uses the generic gpio driver.
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Device tree binding documentation for the TS-4800
GPIO controller.
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
[Point ngpios to gpio.txt]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use irq_data_get_chip_type() instead of container_of().
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The gpio-mpc8xxx.c should can support qoriq and
Layerscape platforms.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add F81866 GPIO supports

Fintek F81866 is a SuperIO. It contains HWMON/GPIO/Serial Ports.
and it has totally 72(9x8 sets) gpio pins.

Here is the PDF spec:
http://www.alldatasheet.com/datasheet-pdf/pdf/459085/FINTEK/F81866AD-I.html

The control method is the same with F7188x, but we should care the address
of GPIO8x.

GPIO address is below:
    GPIO0x based: 0xf0
    GPIO1x based: 0xe0
    GPIO2x based: 0xd0
    GPIO3x based: 0xc0
    GPIO4x based: 0xb0
    GPIO5x based: 0xa0
    GPIO6x based: 0x90
    GPIO7x based: 0x80
    GPIO8x based: 0x88 <-- not 0x70.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The ACCES 104-DIO-48E device provides 48 lines digital I/O via two
Programmable Peripheral Interface (PPI) chips of type 82C55. Bit C3 at
each 24-bit Group can be used as an external interrupt, triggered by a
rising edge.

This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the dio_48e_base module parameter. The interrupt line number for the
device may be configured via the dio_48e_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The WinSystems WS16C48 device provides 48 lines of digital I/O. In
addition, the first 24 lines may be used for interrupt-handled edge
detection; rising edge detection and falling edge detection are
supported.

This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the ws16c48_base module parameter. The interrupt line number for the
device may be configured via the ws16c48_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The ACCES 104-IDI-48 can differentiate between its own and other
devices' interrupt requests. Therefore, IRQ sharing is possible and
should be permitted.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Steven Miao <realmz6@gmail.com>
Cc: adi-buildroot-devel@lists.sourceforge.net
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.

  The executive summary:

   - ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
   - Avoid useless rebuilds for zboot.
   - jz4780: Add NEMC, BCH and NAND device tree nodes
   - Initial support for the MicroChip's DT platform.  As all the device
     drivers are missing this is still of limited use.
   - Some Loongson3 cleanups.
   - The unavoidable whitespace polishing.
   - Reduce clock skew when synchronizing the CPU cycle counters on CPU
     startup.
   - Add MIPS R6 fixes.
   - Lots of cleanups across arch/mips as fallout from KVM.
   - Lots of minor fixes and changes for IEEE 754-2008 support to the
     FPU emulator / fp-assist software.
   - Minor Ralink, BCM47xx and bcm963xx platform support improvments.
   - Support SMP on BCM63168"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
  MIPS: zboot: Add support for serial debug using the PROM
  MIPS: zboot: Avoid useless rebuilds
  MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
  MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
  MIPS: bcm963xx: Update bcm_tag field image_sequence
  MIPS: bcm963xx: Move extended flash address to bcm_tag header file
  MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
  MIPS: bcm63xx: nvram: Use nvram structure definition from header file
  MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
  MAINTAINERS: Add KVM for MIPS entry
  MIPS: KVM: Add missing newline to kvm_err()
  MIPS: Move KVM specific opcodes into asm/inst.h
  MIPS: KVM: Use cacheops.h definitions
  MIPS: Break down cacheops.h definitions
  MIPS: Use EXCCODE_ constants with set_except_vector()
  MIPS: Update trap codes
  MIPS: Move Cause.ExcCode trap codes to mipsregs.h
  MIPS: KVM: Make kvm_mips_{init,exit}() static
  MIPS: KVM: Refactor added offsetof()s
  MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
  ...

Merge tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform driver updates from Darren Hart:
 "Emergency travel prevented me from completing my final testing on this
  until today.  Nothing here that couldn't wait until RC1 fixes, but I
  thought it best to get it out sooner rather than later as it does
  contain a build warning fix.

  Summary:

  A build warning fix, MAINTAINERS cleanup, and a new DMI quirk:

  ideapad-laptop:
   - Add Lenovo Yoga 700 to no_hw_rfkill dmi list

  MAINTAINERS:
   - Combine multiple telemetry entries

  intel_telemetry_debugfs:
   - Fix unused warnings in telemetry debugfs"

* tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
  MAINTAINERS: Combine multiple telemetry entries
  intel_telemetry_debugfs: Fix unused warnings in telemetry debugfs

Pull thermal management updates from Zhang Rui:
 "The top merge commit was re-generated yesterday because two topic
  branches were dropped from this pull request in the last minute due to
  some unaddressed comments.  All the other material has been in
  linux-next for quite a while.

  Specifics:

   - Enhance thermal core to handle unexpected device cooling states
     after fresh boot and system resume.  From Zhang Rui and Chen Yu.

   - Several fixes and cleanups on Rockchip and RCAR thermal drivers.
     From Caesar Wang and Kuninori Morimoto.

   - Add Broxton support for Intel processor thermal reporting device
     driver.  From Amy Wiles"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: trip_point_temp_store() calls thermal_zone_device_update()
  thermal: rcar: rcar_thermal_get_temp() return error if strange temp
  thermal: rcar: check irq possibility in rcar_thermal_irq_xxx()
  thermal: rcar: check every rcar_thermal_update_temp() return value
  thermal: rcar: move rcar_thermal_dt_ids to upside
  thermal: rockchip: Support the RK3399 SoCs in thermal driver
  thermal: rockchip: Support the RK3228 SoCs in thermal driver
  dt-bindings: rockchip-thermal: Support the RK3228/RK3399 SoCs compatible
  thermal: rockchip: fix a trivial typo
  Thermal: Enable Broxton SoC thermal reporting device
  thermal: constify pch_dev_ops structure
  Thermal: do thermal zone update after a cooling device registered
  Thermal: handle thermal zone device properly during system sleep
  Thermal: initialize thermal zone device correctly

Pull 9p updates from Eric Van Hensbergen:
 "Sorry for the last minute pull request, there's was a change that
  didn't get pulled into for-next until two weeks ago and I wanted to
  give it some bake time.

  Summary:

  Rework and error handling fixes, primarily in the fscatch and fd
  transports"

* tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  fs/9p: use fscache mutex rather than spinlock
  9p: trans_fd, bail out if recv fcall if missing
  9p: trans_fd, read rework to use p9_parse_header
  net/9p: Add device name details on error

Pull Ceph updates from Sage Weil:
 "The two main changes are aio support in CephFS, and a series that
  fixes several issues in the authentication key timeout/renewal code.

  On top of that are a variety of cleanups and minor bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: remove outdated comment
  libceph: kill off ceph_x_ticket_handler::validity
  libceph: invalidate AUTH in addition to a service ticket
  libceph: fix authorizer invalidation, take 2
  libceph: clear messenger auth_retry flag if we fault
  libceph: fix ceph_msg_revoke()
  libceph: use list_for_each_entry_safe
  ceph: use i_size_{read,write} to get/set i_size
  ceph: re-send AIO write request when getting -EOLDSNAP error
  ceph: Asynchronous IO support
  ceph: Avoid to propagate the invalid page point
  ceph: fix double page_unlock() in page_mkwrite()
  rbd: delete an unnecessary check before rbd_dev_destroy()
  libceph: use list_next_entry instead of list_entry_next
  ceph: ceph_frag_contains_value can be boolean
  ceph: remove unused functions in ceph_frag.h