The 'reset' argument is clearly a boolean, so use bool instead
of u8 with 0/1 values.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If there's no LED on the system, it doesn't make a lot of sense
to include close to 4k of LED-related code (mostly in mac80211),
so instead of forcing LED support into the kernel, don't build
iwlwifi/mac80211 LED support if there's no LED class support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: EliadX Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The old code checks if hw_section_num is valid while the
right thing to do is to check if section[hw_section_num].data
is valid.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

For family 8000 products, the driver should take the MAC
address from the mac_override section and only if this
section is empty it should take it from the HW section.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Read first the nvm sections from the OTP, then read the nvm
sections from the external file and override the OTP values
(if there were any values in the OTP).
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

A few devices aren't allowed to be powered up at driver
load time. Add "power_up_nic_in_init" flag to iwl_cfg
structure to customize the load flow according to the
device.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

OTP size changed in family 7000 and in family 8000.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

There's no need to use a variable just to return the result
of another function call at the end of a function, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The expected throughput table used when estimating a new column
depends on the channel bandwidth. When switching from legacy to
siso or mimo the wrong expected throughput table was used as it
was chosen based on the the channel bandwidth in legacy which is
always 20Mhz. Instead it should be chosen based on the current sta
bandwidth which could be also 40Mhz or 80Mhz.
When enabling MCS9 this bug leads to a problem where the max
expected throughput of the siso or mimo column is 0 as MCS9 isn't
supported in 20Mhz. This in turns prevents switching to siso or mimo.

Fix this by using the sta bandwidth when deciding which table to choose.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

TPC is a power optimization which should only be attempted when
we're in the "stay in column" state after we've locked onto an optimal
rate.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently we were checking only if the driver power_scheme is set
to CAM. TPC shouldn't be enabled also when disabling powersave on the
interface (e.g. iw wlan0 set power_save off)
which may occur even if power_scheme wasn't set to CAM.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

rs_get_best_rate determines the optimal rate to try in a
new Tx column. Currently we were sometimes trying a too high
rate which would lead us to fail and avoid switching to the
new column despite it having a potential to be better.
Change the logic to try and find the first rate which would
exceed the current actual throughput or be more aggressive
if the success ratio is good.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Adding more options in the search cycle causes longer
search cycles with additional wondering off to non optimal Tx
configurations. Reduce the Tx configurations searched to
improve throughput in non optimal attenuations.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

My bad - I forgot to update this when sending the patch
upstream.

Fixes: 87d5e415 ("iwlwifi: mvm: rs: reinit rs if no tx for a long time")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The commit below introduced a bug in the validity bits in
init. Due to that, all the Coex mechanism stopped sending
kills to the BT side. Fix that.

Fixes: b9fae2d5 ("iwlwifi: mvm: BT Coex add support for Co-running block")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: Jahnavi Meher <jahnavi.meher@redpinesignals.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Adjust FIR filter co-efficients to improve EVM for 11b rates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * rfsat gainchange hysteresis of rf_gain stuck with large
   interference present.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I was reading ath5k power setting code and
noticed typing error in ath5k_hw_txpower function.
Invalid value was written to AR5K_PHY_TXPOWER_RATE_MAX
register.
Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use a newline character appropriately.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Coverity CID 986698 reports leakage of struct wlcore_platdev_data in the
probe functions of both the SPI/SDIO interfaces. The structure passed to
platform_device_add_data() is dynamically allocated and only freed in the
error paths, however, platform_device_add_data() adds a copy of the platform
specific data to the device. Move the temporary struct that is kmemdup'ed
to the stack. This issue exists since afb43e6d (wlcore: remove if_ops from
platform_data).
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

94010fa0 ("rtlwifi: add MSI interrupts
mode support") introduced MSI interrupts mode support, which seemed
safe enough with RTL8188EE and RTL8723BE as RealTek's testing results,
but some users reported their RTL8188EE modules could not connect to
any wireless network after the MSI mode was enabled by Ubuntu 14.04.

So, let's fallback to pin-based mode until rtlwifi's MSI support get
good compatibility.

BugLink: https://bugs.launchpad.net/bugs/1310512Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reverts commit 2a54eb5e
("rtlwifi: rtl8188ee: enable MSI interrupts mode").

94010fa0 ("rtlwifi: add MSI interrupts
mode support") introduced MSI interrupts mode support, which seemed
safe enough with RTL8188EE and RTL8723BE as RealTek's testing results,
but some users reported their RTL8188EE modules could not connect to
any wireless network after the MSI mode was enabled by Ubuntu 14.04.

So, let's fallback to pin-based mode until rtlwifi's MSI support get
good compatibility.

BugLink: https://bugs.launchpad.net/bugs/1310512Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Setting it to true during init doesn't seem to be any workaround while
it can cause problems (not enabling radio due to belief it's enabled).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This removes dealing with pointers directly and allows tracking radio
state with radio_on variable.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Conflicts:
	net/mac80211/chan.c

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

mac80211 takes care of all the needed steps for hwsim, so indicate
support for this capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Implement the new cfg80211 capability to enable mac80211-based drivers
to support for dynamic channel bandwidth changes (e.g., HT 20/40 MHz
changes).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This extends NL80211_CMD_SET_CHANNEL to allow dynamic channel bandwidth
changes in AP mode (including P2P GO) during a lifetime of the BSS. This
can be used to implement, e.g., HT 20/40 MHz co-existence rules on the
2.4 GHz band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

P2P_DEVICE doesn't support ieee80211_bss_info_change_notify() for now,
so it's not needed to set changed flags for P2P_DEVICE.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

ieee80211_assign_chanctx() checks if local->use_chanctx is true, so
the two code block related to ieee80211_assign_chanctx() can be moved
into above if clause, emphasize that these code are executed only if
local->use_chanctx is true.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
[change subject]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Current code checks if the 20MHz bandwidth is allowed for
particular channel -- if it is not, the channel is disabled.
Since we need to use 5/10 MHz channels, this code is modified in
the way that the default bandwidth to check is 5MHz. If the
maximum bandwidth allowed by the channel is smaller than 5MHz,
the channel is disabled. Otherwise the channel is used and the
flags are set according to the bandwidth allowed by the channel.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since there are frequency bands (e.g. 5.9GHz) allowing channels
with only 10 or 5 MHz bandwidth, this patch adds attributes that
allow keeping track about this information.

When channel attributes are reported to user-space, make sure to
not break old tools, i.e. if the 'split wiphy dump' is enabled,
report the extra attributes (if present) describing the bandwidth
restrictions.  If the 'split wiphy dump' is not enabled,
completely omit those channels that have flags set to either
IEEE80211_CHAN_NO_10MHZ or IEEE80211_CHAN_NO_20MHZ.

Add the check for new bandwidth restriction flags in
cfg80211_chandef_usable() to comply with the restrictions.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Return NOTIFY_DONE if we don't care this time's notification, return
NOTIFY_OK if we successfully handled this time's notification. That's
the formal way to do it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Return NOTIFY_DONE if we don't care this time's notification, return
NOTIFY_OK if we successfully handled this time's notification. That's
the formal way to do it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>