This patch adds new iface type (NL80211_IFTYPE_OCB) representing
the OCB (Outside the Context of a BSS) mode.
When establishing a connection to the network a cfg80211_join_ocb
function is called (particular nl80211_command is added as well).
A mandatory parameters during the ocb_join operation are 'center
frequency' and 'channel width (5/10 MHz)'.

Changes done in mac80211 are minimal possible required to avoid
many warnings (warning: enumeration value 'NL80211_IFTYPE_OCB'
not handled in switch) during compilation. Full functionality
(where needed) is added in the following patch.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The configured tx power is often limited by hardware capabilities,
channel settings, antenna configuration, etc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix tracing compilation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Maximum length of AMPDU that an STA can receive in VHT.
length = 2 ^ (13 + max_ampdu_length_exp) - 1.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Most code avoids having a default case in interface type switch
statements already, to make it easier to find places that need
to be extended. Change the code in the __cfg80211_leave() and
nl80211_key_allowed() functions to not have a default case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When deleting old radio via HWSIM_CMD_DEL_RADIO then listeners on the
multicast group "config" are informed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When adding new radio via HWSIM_CMD_NEW_RADIO then listeners on the
multicast group "config" are informed.

While at it, refactor the configuration parameters to be able to
pass them directly and have fewer function arguments.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

A few recent additions to the netlink attributes neglected
to add policy entries, fix that now.
Reported-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Use codespell to find spelling errors.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This newline shouldn't be there, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This lets hostapd start if you have SGI-20 configured
as one of your HT capabilities.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The helper function can't ever create negative values, so use
u32 pointers as the function arguments as the caller does.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

radar_detect_width is unused since commit 97dc94f1
("cfg80211: remove channel_switch combination check")
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add frequency attribute when sending to user-space over
netlink socket.  The frequency is currently ignored when
receiving from user-space.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Using the name HWSIM_CMD_NEW_RADIO and HWSIM_CMD_DEL_RADIO is more
fitting on how other pieces of the wireless system work.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When CONFIG_MAC80211_RC_MINSTREL_VHT is set, the module param
minstrel_vht_only tells minstrel_ht whether to allow the mix of ht rates
with vht rates.
ATM, minstrel_ht skips ht rates when minstrel_vht_only is true, but it does
that even if vht is not supported, which makes the sta rates fallback to
legacy as no ht rate gets enabled.

Fixes: 9208247d ("mac80211: minstrel_ht: add basic support for VHT rates <= 3SS@80MHz")
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

All the callers of ieee80211_mgd_probe_ap_send return right
after they call the flush() callback. This means that calling
flush() is uneeded since its meaning is to wait until the
queues of the device are empty.

Devices that know how to report status on Tx will do so using
the regular path (ieee80211_tx_status) and this status will
trigger the continuation of the flow of the probe
(ieee80211_sta_tx_notify).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This is useful when creating virtual interfaces.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This is useful when creating virtual interfaces.
Keeps udev from mucking with things it shouldn't, since
the default MAC is never seen by udev when specified on
the cmd-line during creation.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[check for feature flag in nl80211 to force drivers to set it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Good for automated testing, where user can create wlan
interfaces with specified names.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This will be helpful when using the mac80211_hwsim
wiphys and automated testing.  Let user create the
vifs as needed, and named as expected.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Otherwise, it can be very difficult to know which is which
if you are trying to do detailed testing.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Support creating wiphy devices with an optional name.
This will be used by hwsim to have better automated control
over virtual radio creation/deletion.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Kernel will attempt to use the name if it is supplied,
but if name cannot be used for some reason, the default
phyX name will be used instead.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[while at it, use wiphy_name() instead of dev_name(),
 fix format string issue reported by Kees Cook]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

It is not always convenient to have to know the device-id,
so allow deleting by name as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[use wiphy_name() instead of dev_name()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This gives a view into packet activity at the virtual radio
level.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Allow drivers to iterate all stations currently uploaded to them.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

During reconfig the station list is traversed in order and station are
added back to the driver. Make sure the stations are added to the driver
in the same order they were added to mac80211.

This has a real side effect - some drivers (iwlwifi) require TDLS
stations to be added only after the AP station for the same network.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some drivers need to know which station is the TDLS link initiator.
Expose this value via the mac80211 ieee80211_sta structure.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When an IV is generated, only the MAC header is moved back. The network
header location remains the same relative to the skb head, as the new IV
is using headroom space that was reserved in advance.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Export ieee80211_ie_split function, so it can be reused by
drivers which need to insert additional elements.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When displaying a rate through debugfs minstrel_ht guesses its flags
comparing group indexes.  Since 3ec373c4 ("mac80211: minstrel_ht:
include type (cck/ht) in rates flag"), the rate flags of interest are
present in the mcs_group-s, so use it.
While improving the code, this also fixes a smatch false positive
"error: testing array offset 'i' after use" in minstrel_ht_stats_dump.
This warning only triggers after 9208247d ("mac80211: minstrel_ht:
add basic support for VHT rates <= 3SS@80MHz") with
CONFIG_MAC80211_RC_MINSTREL_VHT unset because then MINSTREL_VHT_GROUP_0
is above MINSTREL_GROUPS_NB and smatch only barks when the "testing
array offset" seems to prevent possible out of bonds accesses (which
does not happen here since i < ARRAY_SIZE(mi->groups)).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When a key is tainted during resume, it is no longer programmed
into the device; however, it's uploaded flag may (will) be set.
Clear the flag when not programming it because it's tainted to
avoid attempting to remove it again later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Use the currently existing APIs between mac80211 and the low
level driver to implement WMM admission control.

The low level driver needs to report the media time used by
each transmitted packet in ieee80211_tx_status. Based on that
information, mac80211 will modify the QoS parameters of the
admission controlled Access Category when the limit is
reached. Once the original QoS parameters can be restored,
mac80211 will do so.

One issue with this approach is that management frames will
also erroneously be downgraded, but the upside is that the
implementation is simple. In the future, it can be extended
to driver- or device-based implementations that are better.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's no reason to ever set invalid CW_min/CW_max to the
drivers, we should catch it in higher layers. However, the
consequences of setting it wrong can be quite severe, so
double-check at a low level and error out for invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

During the review of the corresponding wpa_supplicant patches we
noticed that the only way for it to detect that this functionality
is supported currently is to check for the command support. This
can be misleading though, as the command was also designed to, in
the future, support pure 802.11 TSPECs.

Expose the WMM-TSPEC feature flag to nl80211 so later we can also
expose an 802.11-TSPEC feature flag (if needed) to differentiate
the two cases.

Note: this change isn't needed in 3.18 as there's no driver there
yet that supports the functionality at all.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The debugfs_remove() function can safely take NULL parameters
so the additionally null test isn't required, and there's no
other reason to have it here, so remove it.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
[rewrite commit message, re-introduce blank line after assert]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When the new CONFIG_MAC80211_RC_MINSTREL_VHT is not set (default 'N'),
there is no behavioral change including in sampling and MCS_GROUP_RATES
remains 8.
Otherwise MCS_GROUP_RATES is 10, and a module parameter *vht_only*
(default 'true'), restricts the rates selection to VHT when VHT is
supported.

Regarding the debugfs stats buffer:
It is explicitly increased from 8k to 32k to fit every rates incl. when
both HT and VHT rates are enabled, as for the format, before:
type           rate     tpt eprob *prob ret  *ok(*cum)        ok(      cum)
HT20/LGI ABCDP MCS0     0.0   0.0   0.0   1    0(   0)         0(        0)
after:
 type           rate      tpt eprob *prob ret  *ok(*cum)        ok(      cum)
 HT20/LGI ABCDP MCS0      0.0   0.0   0.0   1    0(   0)         0(        0)
VHT40/LGI       MCS5/2    0.0   0.0   0.0   0    0(   0)         0(        0)
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

ATM, we grep cck rates idx with idx / MCS_GROUP_RATES ==
MINSTREL_CCK_GROUP.
Matching neither-cck-non-ht rates could be done by replacing '==' with
'>', however it would be less versatile or explicit.
This will allow to match VHT rates with IEEE80211_TX_RC_VHT_MCS.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

No functional change.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since 5935839a ("mac80211: improve minstrel_ht rate sorting by
throughput & probability"), the rate indexes are manipulated via u8's
and hence allow for a maximum of 256 mcs_group entries in
minstrel_mcs_groups.

ATM, minstrel_ht advertizes support up to 3HTSS@40MHz, consuming:
8(MCS_GROUP_RATES) * (3(SS)*2(GI)*2(BW)+1(CCK)), i.e. 104 entries.

Support for 3VHTSS@80MHz will require:
10(MCS_GROUP_RATES) * (3(SS)*2(GI)*2(BW)+1(CCK)) +
10(MCS_GROUP_RATES) * (3(SS)*2(GI)*3(BW)), i.e. 130 + 180 entries.

This change moves from u8s to u16s where necessary.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>