- 25 Jul, 2018 4 commits
-
-
Rob Clark authored
f9cb8d8d fixed various race conditions with CTL flush, in particular flushing and sending the START signal before encoder state was updated. But it did this a little too well in some cases that don't trigger encoder->enable(), and CTL[n].FLUSH would never be set. When page flips happen it would paper over the bug, since the first plag flip would flush out the state to the hardware. The issue could be reproduced with, for example, modetest (without the '-v' argument). Fixes: f9cb8d8d drm/msm/mdp5: rework CTL START signal handling Signed-off-by:
Rob Clark <robdclark@gmail.com> Reviewed-by:
Sean Paul <seanpaul@chromium.org>
-
Jordan Crouse authored
Experimentation shows that resuming power quickly after suspending ends up forcing a system hang for unknown reasons on 5xx targets. To avoid cycling the power too much (especially during init) turn up the autosuspend time for a5xx to 250ms and use pm_runtime_put_autosuspend() when applicable. Signed-off-by:
Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by:
-
Daniel Mack authored
When a msm8016 based system is woken up from suspend, the firmware in the adreno device hangs. [ 83.903416] qcom-iommu-ctx 1f09000.iommu-ctx: Unhandled context fault: fsr=0x202, iova=0x0000000000000000, fsynr=0x2, cb=1 [ 85.853633] msm 1a00000.mdss: A306: hangcheck detected gpu lockup rb 0! [ 85.853661] msm 1a00000.mdss: A306: completed fence: 370 [ 85.859073] msm 1a00000.mdss: A306: submitted fence: 372 [ 85.865113] msm 1a00000.mdss: A306: hangcheck recover! Fix this by adding pm_runtime_force_suspend/pm_runtime_force_resume as sleep ops. Signed-off-by:
Daniel Mack <daniel@zonque.org> Signed-off-by:
-
Daniel Mack authored
To make suspend and resume work on msm8916 platforms, call into the generic helpers and preserve the state across suspends. Signed-off-by:
-
- 20 Jul, 2018 4 commits
-
-
git://people.freedesktop.org/~agd5f/linuxDave Airlie authored
More features for 4.19: - Map processes to vmids for debugging GPUVM faults - Raven gfxoff fixes - Initial gfxoff support for vega12 - Use defines for interrupt sources rather than magic numbers - DC aux fixes - Finish DC logging TODO - Add more DC debugfs interfaces for conformance testing - Add CRC support for DCN - Scheduler rework in preparation for load balancing - Unify common smu9 code - Clean up UVD instancing support - ttm cleanups - Misc fixes and cleanups Signed-off-by:
Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180719194001.3488-1-alexander.deucher@amd.com
-
git://anongit.freedesktop.org/drm/drm-intelDave Airlie authored
On GEM side: - GuC related fixes (Chris, Michal) - GTT read-only pages support (Jon, Chris) - More selftests fixes (Chris) - More GPU reset improvements (Chris) - Flush caches after GGTT writes (Chris) - Handle recursive shrinker for vma->last_active allocation (Chris) - Other execlists fixes (Chris) On Display side: - GLK HDMI fix (Clint) - Rework and cleanup around HPD pin (Ville) - Preparation work for Display Stream Compression support coming on ICL (Anusha) - Nuke LVDS lid notification (Ville) - Assume eDP is always connected (Ville) - Kill intel panel detection (Ville) Signed-off-by:
-
git://anongit.freedesktop.org/drm/drm-miscDave Airlie authored
drm-misc-next for 4.19: Core Changes: - add support for DisplayPort CEC-Tunneling-over-AUX (Hans Verkuil) - more doc updates (Daniel Vetter) - fourcc: Add is_yuv field to drm_format_info (Ayan Kumar Halder) - dma-buf: correctly place BUG_ON (Michel Dänzer) Driver Changes: - more vkms support(Rodrigo Siqueira) - many fixes and small improments to all drivers Signed-off-by:
-
git://github.com/skeggsb/linuxDave Airlie authored
misc fixes and cleanups for next. Signed-off-by:
-
- 19 Jul, 2018 17 commits
-
-
Christian König authored
The whole handle, filp and entity handling is superfluous here. We should have reviewed that more thoughtfully. It looks like somebody just made the code instance aware without knowing the background. v2: fix one more missed case in amdgpu_uvd_suspend Reviewed-by:
Leo Liu <leo.liu@amd.com> Signed-off-by:
Christian König <christian.koenig@amd.com> Acked-by:
Chunming Zhou <david1.zhou@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Christian König authored
Not sure what that was every used for, but now it is completely unused. Reviewed-by:
-
Michel Dänzer authored
Allowing CONFIG_DRM_AMD_DC_DCN1_0 to be disabled on X86 was an opportunity for display with Raven Ridge accidentally not working. Reviewed-by:
Harry Wentland <harry.wentland@amd.com> Signed-off-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
-
Evan Quan authored
The 'result' is not initialized correctly. It causes the API return an error code even on success. Signed-off-by:
Evan Quan <evan.quan@amd.com> Acked-by:
Huang Rui <ray.huang@amd.com> Signed-off-by:
-
Alex Deucher authored
Use the newly added irq source defines rather than magic numbers for smu7 thermal interrupts. Rewiewed-by:
Rex Zhu <rezhu@amd.com> Signed-off-by:
-
Rodrigo Vivi authored
Signed-off-by:Rodrigo Vivi <rodrigo.vivi@intel.com>
-
Ville Syrjälä authored
With neither LVDS or eDP no longer using intel_panel_detect() we can kill it, and the accompanying modparam. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180717174216.22252-3-ville.syrjala@linux.intel.comReviewed-by:
-
Ville Syrjälä authored
We never registered any kind of lid notifier for eDP, so looking at the lid status is pretty much bonkers. Let's just consider eDP always connected instead. Signed-off-by:
-
Ville Syrjälä authored
We broke the LVDS notifier resume thing in (presumably) commit e2c8b870 ("drm/i915: Use atomic helpers for suspend, v2.") as we no longer duplicate the current state in the LVDS notifier and thus we never resume it properly either. Instead of trying to fix it again let's just kill off the lid notifier entirely. None of the machines tested thus far have apparently needed it. Originally the lid notifier was added to work around cases where the VBIOS was clobbering some of the hardware state behind the driver's back, mostly on Thinkpads. We now have a few report of Thinkpads working just fine without the notifier. So maybe it was misdiagnosed originally, or something else has changed (ACPI video stuff perhaps?). If we do end up finding a machine where the VBIOS is still causing problems I would suggest that we first try setting various bits in the VBIOS scratch registers. There are several to choose from that may instruct the VBIOS to steer clear. With the notifier gone we'll also stop looking at the panel status in ->detect(). v2: Nuke enum modeset_restore (Rodrigo) Cc: stable@vger.kernel.org Cc: Wolfgang Draxinger <wdraxinger.maillist@draxit.de> Cc: Vito Caputo <vcaputo@pengaru.com> Cc: kitsunyan <kitsunyan@airmail.cc> Cc: Joonas Saarinen <jza@saunalahti.fi> Tested-by: Vito Caputo <vcaputo@pengaru.com> # Thinkapd X61s Tested-by: kitsunyan <kitsunyan@airmail.cc> # ThinkPad X200 Tested-by: Joonas Saarinen <jza@saunalahti.fi> # Fujitsu Siemens U9210 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105902 References: https://lists.freedesktop.org/archives/intel-gfx/2018-June/169315.html References: https://bugs.freedesktop.org/show_bug.cgi?id=21230 Fixes: e2c8b870 ("drm/i915: Use atomic helpers for suspend, v2.") Signed-off-by:
-
Chris Wilson authored
There's a race between idling the engine and finishing off the last tasklet (as we may kick the tasklets after declaring an individual engine idle). However, since we do not need to access the device until we try to submit to the ELSP register (processing the CSB just requires normal CPU access to the HWSP, and when idle we should not need to submit!) we can defer the assertion unto that point. The assertion is still useful as it does verify that we do hold the longterm GT wakeref taken from request allocation until request completion. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107274 Fixes: 9512f985 ("drm/i915/execlists: Direct submission of new requests (avoid tasklet/ksoftirqd)") Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180719075029.28643-1-chris@chris-wilson.co.uk
-
Chris Wilson authored
If we call into the shrinker for direct relcaim inside kmalloc, it will retire the requests. If we retire the vma->last_active while processing a new i915_vma_move_to_active() we can upset the delicate bookkeeping required for the cache. After the possible invocation of the shrinker, we need to double check the vma->last_active is still valid. Fixes: 8b293eb5 ("drm/i915: Track the last-active inside the i915_vma") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105600#c39Signed-off-by:
-
Chris Wilson authored
We make a decision at module load whether to use the GuC backend or not, but lose that setup across set-wedge. Currently, the guc doesn't override the engine->set_default_submission hook letting execlists sneak back in temporarily on unwedging leading to an unbalanced park/unpark. v2: Remove comment about switching back temporarily to execlists on guc_submission_disable(). We currently only call disable on shutdown, and plan to also call disable before suspend and reset, in which case we will either restore guc submission or mark the driver as wedged, making the reset back to execlists pointless. v3: Move reset.prepare across Fixes: 63572937 ("drm/i915/execlists: Flush pending preemption events during reset") Testcase: igt/drv_module_reload/basic-reload-inject Testcase: igt/gem_eio Signed-off-by:
Michał Winiarski <michal.winiarski@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180717202932.1423-1-chris@chris-wilson.co.uk
-
Ben Skeggs authored
Workaround for issues seen on systems with large amounts of RAM, caused by display not supporting the same physical address limits as the other parts of the GPU. Signed-off-by:Ben Skeggs <bskeggs@redhat.com>
-
Anusha Srivatsa authored
RC model has these parameters that correspond with each of 15 ranges of RC buffer threshold value in the RC model. The three elements are range_min_qp, range_max_qp and range_bpg_offset. Add the Rate Control range values for eDP/MIPI and DP case. The actual values are calculated usung a helper function. This patch adds the shifts to registers where the value will be written during atomic commit. v2: - Use _MMIO_PIPE() instead of _MMIO(_PICK()) (Manasi) - Combine shifts (Manasi) Cc: Jose Souza <jose.souza@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
Anusha Srivatsa <anusha.srivatsa@intel.com> Reviewed-by:
Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
-
Anusha Srivatsa authored
Add register defines and shifts that control the RC buffer threshold between encoder and decoder for eDP/MIPI and DP cases. The actual values are calculated usung a helper function. This patch adds the shifts to registers where the value will be written during atomic commit. v2: - Use _MMIO_PIPE() instead of _MMIO_(_PICK()) (Manasi) - Combine shifts (Manasi) Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
-
Anusha Srivatsa authored
Display Stream Compression(DSC) has a set of Picture Parameter Set(PPS) components that the encoder must communicate to the decoder. This patch adds register definitions to the PPS parameters for eDP/MIPI case and Display Port. v2: - Use _MMIO_PIPE instead of _MMIO(_PICK()). (Manasi) - Use DSC constants as arguments. (Manasi) Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
-
Anusha Srivatsa authored
The Picture Parameter Set metadata for DSC has to be sent to the panel through secondary data packets. Add the error correction registers, data registers and control registers for the same. The control registers for transcoders A and B are already defined and will be reused for Icelake purpose. This patch adds Control register for EDP and transcoder C apart from adding the PPS data and error registers. v2: reuse MMIO_TRANS2 for _PPS_DATA and _PPS_ECC. The _MMIO_TRANS2(pipe, reg) macro definition takes care of the eDp case Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
-
- 18 Jul, 2018 15 commits
-
-
Kees Cook authored
In the quest to remove all stack VLA usage from the kernel[1], this uses the maximum sane buffer size and removes copy/paste code. [1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.comReviewed-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Huang Rui authored
BO ptr already be initialized at definition, we needn't use the complicated reference. v2: fix typo at subject line Signed-off-by:
-
Sonny Jiang authored
Remove internal/unused kernel module parameters Signed-off-by:
Sonny Jiang <sonny.jiang@amd.com> Reviewed-by:
-
Christian König authored
Pushing a job can change the ring assignment of an entity. v2: squash in: "drm/amdgpu: fix job priority handling" (Christian) Signed-off-by:
-
Christian König authored
Allow to call amdgpu_ring_priority_get() after pushing the ring to the scheduler. Signed-off-by:
-
Feifei Xu authored
Add some UTCL registers' golden settings. Signed-off-by:
Feifei Xu <Feifei.Xu@amd.com> Tested-by:
Kevin Wang <Kevin1.Wang@amd.com> Signed-off-by:
-
Rodrigo Vivi authored
It was originally introduced following the VESA spec in order to validate PSR. However we found so many issues around sink_crc that instead of helping PSR development it only brought another layer of trouble to the table. So, sink_crc has been a black whole for us in question of time, effort and hope. First of the problems is that HW statement is clear: "Do not attempt to use aux communication with PSR enabled". So the main reason behind sink_crc is already compromised. For a while we had hope on the aux-mutex could workaround this problem on SKL+ platforms, but that mutex was not reliable, not tested, and we shouldn't use according to HW engineers. Also, nor source, nor sink designed and implemented the sink_crc to be used like we are trying to use here. Well, the sink side of things is also apparently not prepared for this case. Each panel that we tried seemed to have a different behavior with same code and same source. So, for all the time we lost on trying to ducktape all these different issues I believe it is now time to move PSR to a more reliable validation. Maybe not a perfect one as we dreamed for this sink_crc, but at least more reliable. Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180705192528.30515-1-rodrigo.vivi@intel.com
-
git://anongit.freedesktop.org/drm/drm-intelDave Airlie authored
Higlights here goes to many PSR fixes and improvements; to the Ice lake work with power well support and begin of DSI support addition. Also there were many improvements on execlists and interrupts for minimal latency on command submission; and many fixes on selftests, mostly caught by our CI. General driver: - Clean-up on aux irq (Lucas) - Mark expected switch fall-through for dealing with static analysis tools (Gustavo) Gem: - Different fixes for GuC (Chris, Anusha, Michal) - Avoid self-relocation BIAS if no relocation (Chris) - Improve debugging cases in on EINVAL return and vma allocation (Chris) - Fixes and improvements on context destroying and freeing (Chris) - Wait for engines to idle before retiring (Chris) - Many improvements on execlists and interrupts for minimal latency on command submission (Chris) - Many fixes in selftests, specially on cases highlighted on CI (Chris) - Other fixes and improvements around GGTT (Chris) - Prevent background reaping of active objects (Chris) Display: - Parallel modeset cleanup to fix driver reset (Chris) - Get AUX power domain for DP main link (Imre) - Clean-up on PSR unused func pointers (Rodrigo) - Many PSR/PSR2 fixes and improvements (DK, Jose, Tarun) - Add a PSR1 live status (Vathsala) - Replace old drm_*_{un/reference} with put,get functions (Thomas) - FBC fixes (Maarten) - Abstract and document the usage of picking macros (Jani) - Remove unnecessary check for unsupported modifiers for NV12. (DK) - Interrupt fixes for display (Ville) - Clean up on sdvo code (Ville) - Clean up on current DSI code (Jani) - Remove support for legacy debugfs crc interface (Maarten) - Simplify get_encoder_power_domains (Imre) Icelake: - MG PLL fixes (Imre) - Add hw workaround for alpha blending (Vandita) - Add power well support (Imre) - Add Interrupt Support (Anusha) - Start to add support for DSI on Ice Lake (Madhav) Signed-off-by: -
Dave Airlie authored
Merge branch 'mediatek-drm-next-4.19' of https://github.com/ckhu-mediatek/linux.git-tags into drm-next This include MT2712 SoC support and removing struct mtk_drm_fb. Signed-off-by:
-
git://anongit.freedesktop.org/drm/drm-miscDave Airlie authored
drm-misc-next for 4.19: Cross-subsystem Changes: - many dt-bindings Doc changes Core Changes: - Encoder clean ups (Ville Syrjälä) - Connector Writeback improvements(Boris Brezillon) - Fake vblank support (Boris Brezillon) - API for in-kernel clients (Noralf Trønnes) - improvements to the path of finding panels(Boris Brezillon) Driver Changes: - initial support for the virtual display driver - vkms(Haneen Mohammed and Rodrigo Siqueira) - panel: add Rocktech RK070ER9427 LCD support (Jagan Teki) - panel: add support for the EDT ETM0700G0EDH6 and EDT ETM0700G0BDH6(Jan Tuerk) - panel: add DLC DLC0700YZG-1 (Philipp Zabel) - panel: add support for BOE HV070WSA-100 (Andrzej Hajda) - panel: add newhaven, nhd-4.3-480272ef-atxl LCD (Tomi Valkeinen) - panel: add support for Innolux G070Y2-L01 (Christoph Fritz) - panel: add support for DataImage SCF0700C48GGU18 (Michal Vokáč) - panel: add support for Sharp LQ035Q7DB03 (Vladimir Zapolskiy) - panel: p079zca: Refactor panel driver to support multiple panels (Lin Huang) - sun4i: Add R40 display engine compatible(Jernej Skrabec) Signed-off-by:
-
Ayan Kumar Halder authored
drm_format_info table has a field 'is_yuv' to denote if the format is yuv or not. The driver is expected to use this instead of having a function for the same purpose. Signed-off-by:
Ayan Kumar halder <ayan.halder@arm.com> Reviewed-by:
-
Ayan Kumar Halder authored
drm_format_info table has a field 'is_yuv' to denote if the format is yuv or not. The driver is expected to use this instead of having a function for the same purpose. Signed-off-by:
-
Ayan Kumar Halder authored
drm_format_info table has a field 'is_yuv' to denote if the format is yuv or not. The driver is expected to use this instead of having a function for the same purpose. Signed-off-by:
-
Ayan Kumar Halder authored
A lot of drivers duplicate the function to check if a format is yuv or not. If we add a field (to denote whether the format is yuv or not) in the drm_format_info table, all the drivers can use this field and it will prevent duplication of similar logic. Signed-off-by:
-
Chris Wilson authored
If the driver is wedged, we skip idling the GPU. However, we may still have a few requests still not retired following the wedging (since they will be waiting for a background worker trying to acquire struct_mutex). As we hold the struct_mutex, always do a quick request retirement in order to flush the wedged path. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107257Signed-off-by:
-
