Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Recent experiments have shown many cores share 0x1E0 register used for
clock management.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some of the newer Broadcom chipsets have longe names like BCM43224,
BCM43225, etc. However Broadcom decided to keep using u16 for storing
them. Use %X or %d depending on chip_id value to avoid BCMA8D8, etc.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Scanning currently uses the TX rate mask to
restrict the rate set, which is bogus. Make
it use the new set of rates from userspace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some P2P scans are not allowed to advertise
11b rates, but that is a rather special case
so instead of having that, allow userspace
to request the rate sets (per band) that are
advertised in scan probe request frames.

Since it's needed in two places now, factor
out some common code parsing a rate array.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Old masks were causing ugly, delayed lock ups.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These are needed by ath6kl for parsing tspec status from an IE.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some cards do not use additional 0x30 offset for SPROM location. We do
not know the real condition for it yet, make it BCM4331 specific for
now.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Following operation was incorrectly translated:
 radio_read(0x0011) -> 0xffff
radio_write(0x0011) <- 0xfff7
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Also change the default channel to 11. This is the first channel closed
driver switches to.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

BCMA_IOCTL is register in agent (AKA wrapper) core, we need to use
special R/W ops for it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/hif_usb.c +135 hif_usb_mgmt_cb(6) warn:
variable dereferenced before check 'cmd'
drivers/net/wireless/ath/ath9k/btcoex.c +77 ath9k_hw_init_btcoex_hw(38)
error: buffer overflow 'ah->hw_gen_timers.gen_timer_index' 32 <=
2009813776
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Kalle Valo has asked me to take over the maintenance of the wl1251
driver.  Thanks Kalle for all his work on the wl1251 driver, I'll try
to keep up with his good work from now on.

At the same time, update the Web URL to something more specific.
There's not much in that page, but we will try to update it soon.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/init.c:199:21: warning: context imbalance
in 'ath9k_reg_rmw' - different lock contexts for basic block
drivers/net/wireless/ath/ath9k/xmit.c:1175:31: warning: context
imbalance in 'ath_drain_txq_list' - unexpected unlock
drivers/net/wireless/ath/ath9k/xmit.c:2047:23: warning: context
imbalance in 'ath_tx_process_buffer' - unexpected unlock
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3041:24: warning: cast to
restricted __le32
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We use all that functions by pointers only. This forces compiler to
create additional duplicated functions that are not inline.
Noticed by Michael in similar bcma code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Harshal Chhaya discovered during network tests, that
several of his clients dropped-off the network. The
captured packets shows that the beacons sent by the
AP are at a much lower power than the other data
packets.

The reason for this mishap: The driver never updated
the beacon phy register, so all beacons were always
sent at the lowest power.

Reference: http://marc.info/?l=linux-wireless&m=131067225105801Reported-by: Harshal Chhaya <harshal@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * reserves feature bit for CCA counters

 * extends hardware register file definitions
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

SPROM rev 9 was discovered on 14e4:4331, it seems to have very similar
layout to rev 8 one. Use the same extracting function until we find some
differences.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We use value supplied via SPROM, or default 10:90 as fallback.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add tx_conf array to save the current tx queues
configuration, and reconfig it on resume (ieee80211_reconfig).

On resume, the driver is being reconfigured. Without
reconfiguring the tx queues as well, the driver might
configure the device to use wrong ac params (e.g. ps-poll
instead of uapsd).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

tx start will start the tx queues: basically configure the SCD
Remove the IWLAGN prefix to SCD defines on the way.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>

Since the ICT is transport related, move all its functions to the transport
layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Since iwlagn_stop_device was the only caller to the rx_stop / tx_stop,
these two don't need to be API any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>

There are still a few functions here and there that should be
put in the transport layer. Mainly the functions that are related to the reclaim flow.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Also create a new file: iwl-trans-int-pcie.h which will include
the non static functions that are shared among the current pcie transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Not needed since the driver split.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Define bitmap for calibration
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

The driver should take the ownership of the uCode as default setting
for later operations after interface up.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>