- 15 Feb, 2019 40 commits
-
-
Greg Kroah-Hartman authored
-
Chuck Lever authored
commit e248aa7b upstream. Two and a half years ago, the client was changed to use gathered Send for larger inline messages, in commit 655fec69 ("xprtrdma: Use gathered Send for large inline messages"). Several fixes were required because there are a few in-kernel device drivers whose max_sge is 3, and these were broken by the change. Apparently my memory is going, because some time later, I submitted commit 25fd86ec ("svcrdma: Don't overrun the SGE array in svc_rdma_send_ctxt"), and after that, commit f3c1fd0e ("svcrdma: Reduce max_send_sges"). These too incorrectly assumed in-kernel device drivers would have more than a few Send SGEs available. The fix for the server side is not the same. This is because the fundamental problem on the server is that, whether or not the client has provisioned a chunk for the RPC reply, the server must squeeze even the most complex RPC replies into a single RDMA Send. Failing in the send path because of Send SGE exhaustion should never be an option. Therefore, instead of failing when the send path runs out of SGEs, switch to using a bounce buffer mechanism to handle RPC replies that are too complex for the device to send directly. That allows us to remove the max_sge check to enable drivers with small max_sge to work again. Reported-by:
Don Dutile <ddutile@redhat.com> Fixes: 25fd86ec ("svcrdma: Don't overrun the SGE array in ...") Cc: stable@vger.kernel.org Signed-off-by:
Chuck Lever <chuck.lever@oracle.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Chuck Lever authored
commit f3c1fd0e upstream. There's no need to request a large number of send SGEs because the inline threshold already constrains the number of SGEs per Send. Signed-off-by:
Sagi Grimberg <sagi@grimberg.me> Signed-off-by:
-
Sven Eckelmann authored
commit 9114daa8 upstream. The caller of ndo_start_xmit may not already have called skb_reset_mac_header. The returned value of skb_mac_header/eth_hdr therefore can be in the wrong position and even outside the current skbuff. This for example happens when the user binds to the device using a PF_PACKET-SOCK_RAW with enabled qdisc-bypass: int opt = 4; setsockopt(sock, SOL_PACKET, PACKET_QDISC_BYPASS, &opt, sizeof(opt)); Since eth_hdr is used all over the codebase, the batadv_interface_tx function must always take care of resetting it. Fixes: c6c8fea2 ("net: Add batman-adv meshing protocol") Reported-by: syzbot+9d7405c7faa390e60b4e@syzkaller.appspotmail.com Reported-by: syzbot+7d20bc3f1ddddc0f9079@syzkaller.appspotmail.com Signed-off-by:
Sven Eckelmann <sven@narfation.org> Signed-off-by:
Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by:
-
Sven Eckelmann authored
commit 955d3411 upstream. It is not allowed to use WARN* helpers on potential incorrect input from the user or transient problems because systems configured as panic_on_warn will reboot due to such a problem. A NULL return value of __dev_get_by_index can be caused by various problems which can either be related to the system configuration or problems (incorrectly returned network namespaces) in other (virtual) net_device drivers. batman-adv should not cause a (harmful) WARN in this situation and instead only report it via a simple message. Fixes: b7eddd0b ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface") Reported-by: syzbot+c764de0fcfadca9a8595@syzkaller.appspotmail.com Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Florian Westphal authored
commit 35e61038 upstream. The check assumes that in transport mode, the first templates family must match the address family of the policy selector. Syzkaller managed to build a template using MODE_ROUTEOPTIMIZATION, with ipv4-in-ipv6 chain, leading to following splat: BUG: KASAN: stack-out-of-bounds in xfrm_state_find+0x1db/0x1854 Read of size 4 at addr ffff888063e57aa0 by task a.out/2050 xfrm_state_find+0x1db/0x1854 xfrm_tmpl_resolve+0x100/0x1d0 xfrm_resolve_and_create_bundle+0x108/0x1000 [..] Problem is that addresses point into flowi4 struct, but xfrm_state_find treats them as being ipv6 because it uses templ->encap_family is used (AF_INET6 in case of reproducer) rather than family (AF_INET). This patch inverts the logic: Enforce 'template family must match selector' EXCEPT for tunnel and BEET mode. In BEET and Tunnel mode, xfrm_tmpl_resolve_one will have remote/local address pointers changed to point at the addresses found in the template, rather than the flowi ones, so no oob read will occur. Reported-by: 3ntr0py1337@gmail.com Reported-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Ilya Dryomov authored
commit 4aac9228 upstream. con_fault() can transition the connection into STANDBY right after ceph_con_keepalive() clears STANDBY in clear_standby(): libceph user thread ceph-msgr worker ceph_con_keepalive() mutex_lock(&con->mutex) clear_standby(con) mutex_unlock(&con->mutex) mutex_lock(&con->mutex) con_fault() ... if KEEPALIVE_PENDING isn't set set state to STANDBY ... mutex_unlock(&con->mutex) set KEEPALIVE_PENDING set WRITE_PENDING This triggers warnings in clear_standby() when either ceph_con_send() or ceph_con_keepalive() get to clearing STANDBY next time. I don't see a reason to condition queue_con() call on the previous value of KEEPALIVE_PENDING, so move the setting of KEEPALIVE_PENDING into the critical section -- unlike WRITE_PENDING, KEEPALIVE_PENDING could have been a non-atomic flag. Reported-by: syzbot+acdeb633f6211ccdf886@syzkaller.appspotmail.com Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Tested-by:
Myungho Jung <mhjungk@gmail.com> Signed-off-by:
-
Theodore Ts'o authored
commit 8fdd60f2 upstream. This reverts commit ad211f3e. As Jan Kara pointed out, this change was unsafe since it means we lose the call to sync_mapping_buffers() in the nojournal case. The original point of the commit was avoid taking the inode mutex (since it causes a lockdep warning in generic/113); but we need the mutex in order to call sync_mapping_buffers(). The real fix to this problem was discussed here: https://lore.kernel.org/lkml/20181025150540.259281-4-bvanassche@acm.org The proposed patch was to fix a syzbot complaint, but the problem can also demonstrated via "kvm-xfstests -c nojournal generic/113". Multiple solutions were discused in the e-mail thread, but none have landed in the kernel as of this writing. Anyway, commit ad211f3e is absolutely the wrong way to suppress the lockdep, so revert it. Fixes: ad211f3e ("ext4: use ext4_write_inode() when fsyncing w/o a journal") Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Reported: Jan Kara <jack@suse.cz> Signed-off-by:
-
Benedict Wong authored
commit e2612cd4 upstream. Fixes 9b42c1f1, which changed the default route lookup behavior for tunnel mode SAs in the outbound direction to use the skb mark, whereas previously mark=0 was used if the output mark was unspecified. In mark-based routing schemes such as Android’s, this change in default behavior causes routing loops or lookup failures. This patch restores the default behavior of using a 0 mark while still incorporating the skb mark if the SET_MARK (and SET_MARK_MASK) is specified. Tested with additions to Android's kernel unit test suite: https://android-review.googlesource.com/c/kernel/tests/+/860150 Fixes: 9b42c1f1 ("xfrm: Extend the output_mark to support input direction and masking") Signed-off-by:
Benedict Wong <benedictwong@google.com> Signed-off-by:
-
Benjamin Coddington authored
This patch is only appropriate for stable kernels v4.16 - v4.19 Since commit 9b30889c ("SUNRPC: Ensure we always close the socket after a connection shuts down"), and until commit c544577d ("SUNRPC: Clean up transport write space handling"), it is possible for the NFS client to spin in the following tight loop: 269.964083: rpc_task_run_action: task:43@0 flags=5a81 state=0005 status=0 action=call_bind [sunrpc] 269.964083: rpc_task_run_action: task:43@0 flags=5a81 state=0005 status=0 action=call_connect [sunrpc] 269.964083: rpc_task_run_action: task:43@0 flags=5a81 state=0005 status=0 action=call_transmit [sunrpc] 269.964085: xprt_transmit: peer=[10.0.1.82]:2049 xid=0x761d3f77 status=-32 269.964085: rpc_task_run_action: task:43@0 flags=5a81 state=0005 status=-32 action=call_transmit_status [sunrpc] 269.964085: rpc_task_run_action: task:43@0 flags=5a81 state=0005 status=-32 action=call_status [sunrpc] 269.964085: rpc_call_status: task:43@0 status=-32 The issue is that the path through call_transmit_status does not release the XPRT_LOCK when the transmit result is -EPIPE, so the socket cannot be properly shut down. The below commit fixed things up in mainline by unconditionally calling xprt_end_transmit() and releasing the XPRT_LOCK after every pass through call_transmit. However, the entirety of this commit is not appropriate for stable kernels because its original inclusion was part of a series that modifies the sunrpc code to use a different queueing model. As a result, there are machinations within this patch that are not needed for a stable fix and will not make sense without a larger backport of the mainline series. In this patch, we take the slightly modified bit of the mainline patch below, which is to release the XPRT_LOCK on transmission error should we detect that the transport is waiting to close. commit c544577d upstream Author: Trond Myklebust <trond.myklebust@hammerspace.com> Date: Mon Sep 3 23:39:27 2018 -0400 SUNRPC: Clean up transport write space handling Treat socket write space handling in the same way we now treat transport congestion: by denying the XPRT_LOCK until the transport signals that it has free buffer space. Signed-off-by:
Trond Myklebust <trond.myklebust@hammerspace.com> The original discussion of the problem is here: https://lore.kernel.org/linux-nfs/20181212135157.4489-1-dwysocha@redhat.com/T/#t This passes my usual cthon and xfstests on NFS as applied on v4.19 mainline. Reported-by:
Dave Wysochanski <dwysocha@redhat.com> Suggested-by:
Trond Myklebust <trondmy@hammerspace.com> Signed-off-by:
Benjamin Coddington <bcodding@redhat.com> Signed-off-by:
-
Thomas Hellstrom authored
commit 728354c0 upstream. The function was unconditionally returning 0, and a caller would have to rely on the returned fence pointer being NULL to detect errors. However, the function vmw_execbuf_copy_fence_user() would expect a non-zero error code in that case and would BUG otherwise. So make sure we return a proper non-zero error code if the fence pointer returned is NULL. Cc: <stable@vger.kernel.org> Fixes: ae2a1040: ("vmwgfx: Implement fence objects") Signed-off-by:
Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by:
Deepak Rawat <drawat@vmware.com> Signed-off-by:
-
Thomas Hellstrom authored
commit 4cbfa1e6 upstream. Previously we set only the dma mask and not the coherent mask. Fix that. Also, for clarity, make sure both are initially set to 64 bits. Cc: <stable@vger.kernel.org> Fixes: 0d00c488: ("drm/vmwgfx: Fix the driver for large dma addresses") Signed-off-by:
-
Lucas De Marchi authored
commit 2a121030 upstream. Even if we don't have the correct clock and get a warning, we should not skip the return. v2: improve commit message (from Joonas) Fixes: 1fa11ee2 ("drm/i915/icl: start adding the TBT pll") Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: <stable@vger.kernel.org> # v4.19+ Signed-off-by:
Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by:
Mika Kahola <mika.kahola@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190125222444.19926-3-lucas.demarchi@intel.com (cherry picked from commit 7a61a6de) Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Gustavo A. R. Silva authored
commit 2f10d823 upstream. Add missing break statement in order to prevent the code from falling through to the default case. The resoning for this is that pclk_vol_table is an automatic variable. So, it makes no sense to update it just before falling through to the default case and return -EINVAL. This bug was found thanks to the ongoing efforts to enabling -Wimplicit-fallthrough. Fixes: cd70f3d6 ("drm/amd/powerplay: PP/DAL interface changes for dynamic clock switch") Cc: stable@vger.kernel.org Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Tina Zhang authored
commit a2fcd5c8 upstream. This patch prevents division by zero htotal. In a follow-up mail Tina writes: > > How did you manage to get here with htotal == 0? This needs backtraces (or if > > this is just about static checkers, a mention of that). > > -Daniel > > In GVT-g, we are trying to enable a virtual display w/o setting timings for a pipe > (a.k.a htotal=0), then we met the following kernel panic: > > [ 32.832048] divide error: 0000 [#1] SMP PTI > [ 32.833614] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.18.0-rc4-sriov+ #33 > [ 32.834438] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.10.1-0-g8891697-dirty-20180511_165818-tinazhang-linux-1 04/01/2014 > [ 32.835901] RIP: 0010:drm_mode_hsync+0x1e/0x40 > [ 32.836004] Code: 31 c0 c3 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 8b 87 d8 00 00 00 85 c0 75 22 8b 4f 68 85 c9 78 1b 69 47 58 e8 03 00 00 99 <f7> f9 b9 d3 4d 62 10 05 f4 01 00 00 f7 e1 89 d0 c1 e8 06 f3 c3 66 > [ 32.836004] RSP: 0000:ffffc900000ebb90 EFLAGS: 00010206 > [ 32.836004] RAX: 0000000000000000 RBX: ffff88001c67c8a0 RCX: 0000000000000000 > [ 32.836004] RDX: 0000000000000000 RSI: ffff88001c67c000 RDI: ffff88001c67c8a0 > [ 32.836004] RBP: ffff88001c7d03a0 R08: ffff88001c67c8a0 R09: ffff88001c7d0330 > [ 32.836004] R10: ffffffff822c3a98 R11: 0000000000000001 R12: ffff88001c67c000 > [ 32.836004] R13: ffff88001c7d0370 R14: ffffffff8207eb78 R15: ffff88001c67c800 > [ 32.836004] FS: 0000000000000000(0000) GS:ffff88001da00000(0000) knlGS:0000000000000000 > [ 32.836004] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 > [ 32.836004] CR2: 0000000000000000 CR3: 000000000220a000 CR4: 00000000000006f0 > [ 32.836004] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 > [ 32.836004] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 > [ 32.836004] Call Trace: > [ 32.836004] intel_mode_from_pipe_config+0x72/0x90 > [ 32.836004] intel_modeset_setup_hw_state+0x569/0xf90 > [ 32.836004] intel_modeset_init+0x905/0x1db0 > [ 32.836004] i915_driver_load+0xb8c/0x1120 > [ 32.836004] i915_pci_probe+0x4d/0xb0 > [ 32.836004] local_pci_probe+0x44/0xa0 > [ 32.836004] ? pci_assign_irq+0x27/0x130 > [ 32.836004] pci_device_probe+0x102/0x1c0 > [ 32.836004] driver_probe_device+0x2b8/0x480 > [ 32.836004] __driver_attach+0x109/0x110 > [ 32.836004] ? driver_probe_device+0x480/0x480 > [ 32.836004] bus_for_each_dev+0x67/0xc0 > [ 32.836004] ? klist_add_tail+0x3b/0x70 > [ 32.836004] bus_add_driver+0x1e8/0x260 > [ 32.836004] driver_register+0x5b/0xe0 > [ 32.836004] ? mipi_dsi_bus_init+0x11/0x11 > [ 32.836004] do_one_initcall+0x4d/0x1eb > [ 32.836004] kernel_init_freeable+0x197/0x237 > [ 32.836004] ? rest_init+0xd0/0xd0 > [ 32.836004] kernel_init+0xa/0x110 > [ 32.836004] ret_from_fork+0x35/0x40 > [ 32.836004] Modules linked in: > [ 32.859183] ---[ end trace 525608b0ed0e8665 ]--- > [ 32.859722] RIP: 0010:drm_mode_hsync+0x1e/0x40 > [ 32.860287] Code: 31 c0 c3 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 8b 87 d8 00 00 00 85 c0 75 22 8b 4f 68 85 c9 78 1b 69 47 58 e8 03 00 00 99 <f7> f9 b9 d3 4d 62 10 05 f4 01 00 00 f7 e1 89 d0 c1 e8 06 f3 c3 66 > [ 32.862680] RSP: 0000:ffffc900000ebb90 EFLAGS: 00010206 > [ 32.863309] RAX: 0000000000000000 RBX: ffff88001c67c8a0 RCX: 0000000000000000 > [ 32.864182] RDX: 0000000000000000 RSI: ffff88001c67c000 RDI: ffff88001c67c8a0 > [ 32.865206] RBP: ffff88001c7d03a0 R08: ffff88001c67c8a0 R09: ffff88001c7d0330 > [ 32.866359] R10: ffffffff822c3a98 R11: 0000000000000001 R12: ffff88001c67c000 > [ 32.867213] R13: ffff88001c7d0370 R14: ffffffff8207eb78 R15: ffff88001c67c800 > [ 32.868075] FS: 0000000000000000(0000) GS:ffff88001da00000(0000) knlGS:0000000000000000 > [ 32.868983] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 > [ 32.869659] CR2: 0000000000000000 CR3: 000000000220a000 CR4: 00000000000006f0 > [ 32.870599] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 > [ 32.871598] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 > [ 32.872549] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b > > Since drm_mode_hsync() has the logic to check mode->htotal, I just extend it to cover the case htotal==0. Signed-off-by:
Tina Zhang <tina.zhang@intel.com> Cc: Adam Jackson <ajax@redhat.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Daniel Vetter <daniel@ffwll.ch> [danvet: Add additional explanations + cc: stable.] Cc: stable@vger.kernel.org Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/1548228539-3061-1-git-send-email-tina.zhang@intel.comSigned-off-by:
-
Felix Fietkau authored
commit 9d0f50b8 upstream. Some drivers use IEEE80211_KEY_FLAG_SW_MGMT_TX to indicate that management frames need to be software encrypted. Since normal data packets are still encrypted by the hardware, crypto_tx_tailroom_needed_cnt gets decremented after key upload to hw. This can lead to passing skbs to ccmp_encrypt_skb, which don't have the necessary tailroom for software encryption. Change the code to add tailroom for encrypted management packets, even if crypto_tx_tailroom_needed_cnt is 0. Cc: stable@vger.kernel.org Signed-off-by:
Felix Fietkau <nbd@nbd.name> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Vincent Whitchurch authored
commit 70ed7148 upstream. KASAN detects a use-after-free when vop devices are removed. This problem was introduced by commit 0063e8bb ("virtio_vop: don't kfree device on register failure"). That patch moved the freeing of the struct _vop_vdev to the release function, but failed to ensure that vop holds a reference to the device when it doesn't want it to go away. A kfree() was replaced with a put_device() in the unregistration path, but the last reference to the device is already dropped in unregister_virtio_device() so the struct is freed before vop is done with it. Fix it by holding a reference until cleanup is done. This is similar to the fix in virtio_pci in commit 2989be09 ("virtio_pci: fix use after free on release"). ================================================================== BUG: KASAN: use-after-free in vop_scan_devices+0xc6c/0xe50 [vop] Read of size 8 at addr ffff88800da18580 by task kworker/0:1/12 CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.0.0-rc4+ #53 Workqueue: events vop_hotplug_devices [vop] Call Trace: dump_stack+0x74/0xbb print_address_description+0x5d/0x2b0 ? vop_scan_devices+0xc6c/0xe50 [vop] kasan_report+0x152/0x1aa ? vop_scan_devices+0xc6c/0xe50 [vop] ? vop_scan_devices+0xc6c/0xe50 [vop] vop_scan_devices+0xc6c/0xe50 [vop] ? vop_loopback_free_irq+0x160/0x160 [vop_loopback] process_one_work+0x7c0/0x14b0 ? pwq_dec_nr_in_flight+0x2d0/0x2d0 ? do_raw_spin_lock+0x120/0x280 worker_thread+0x8f/0xbf0 ? __kthread_parkme+0x78/0xf0 ? process_one_work+0x14b0/0x14b0 kthread+0x2ae/0x3a0 ? kthread_park+0x120/0x120 ret_from_fork+0x3a/0x50 Allocated by task 12: kmem_cache_alloc_trace+0x13a/0x2a0 vop_scan_devices+0x473/0xe50 [vop] process_one_work+0x7c0/0x14b0 worker_thread+0x8f/0xbf0 kthread+0x2ae/0x3a0 ret_from_fork+0x3a/0x50 Freed by task 12: kfree+0x104/0x310 device_release+0x73/0x1d0 kobject_put+0x14f/0x420 unregister_virtio_device+0x32/0x50 vop_scan_devices+0x19d/0xe50 [vop] process_one_work+0x7c0/0x14b0 worker_thread+0x8f/0xbf0 kthread+0x2ae/0x3a0 ret_from_fork+0x3a/0x50 The buggy address belongs to the object at ffff88800da18008 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 1400 bytes inside of 2048-byte region [ffff88800da18008, ffff88800da18808) The buggy address belongs to the page: page:ffffea0000368600 count:1 mapcount:0 mapping:ffff88801440dbc0 index:0x0 compound_mapcount: 0 flags: 0x4000000000010200(slab|head) raw: 4000000000010200 ffffea0000378608 ffffea000037a008 ffff88801440dbc0 raw: 0000000000000000 00000000000d000d 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88800da18480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88800da18500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff88800da18580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff88800da18600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88800da18680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== Fixes: 0063e8bb ("virtio_vop: don't kfree device on register failure") Signed-off-by:
Vincent Whitchurch <vincent.whitchurch@axis.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Aneesh Kumar K.V authored
commit 579b9239 upstream. With support for split pmd lock, we use pmd page pmd_huge_pte pointer to store the deposited page table. In those config when we move page tables we need to make sure we move the deposited page table to the correct pmd page. Otherwise this can result in crash when we withdraw of deposited page table because we can find the pmd_huge_pte NULL. eg: __split_huge_pmd+0x1070/0x1940 __split_huge_pmd+0xe34/0x1940 (unreliable) vma_adjust_trans_huge+0x110/0x1c0 __vma_adjust+0x2b4/0x9b0 __split_vma+0x1b8/0x280 __do_munmap+0x13c/0x550 sys_mremap+0x220/0x7e0 system_call+0x5c/0x70 Fixes: 675d9952 ("powerpc/book3s64: Enable split pmd ptlock.") Cc: stable@vger.kernel.org # v4.18+ Signed-off-by:
Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Sudeep Holla authored
commit 46edb8d1 upstream. The device/driver model clearly mandates that bus driver that discover and allocate the device must set the release callback. This callback will be used to free the device after all references have gone away. scmi bus driver is missing the obvious callback which will result in the following warning if the device is unregistered: Device 'scmi_dev.1' does not have a release() function, it is broken and must be fixed. See Documentation/kobject.txt. WARNING at drivers/base/core.c:922 device_release+0x8c/0xa0 Hardware name: ARM LTD Juno Development Platform BIOS EDK II Jan 21 2019 Workqueue: events deferred_probe_work_func pstate: 60000005 (nZCv daif -PAN -UAO) pc : device_release+0x8c/0xa0 lr : device_release+0x8c/0xa0 Call trace: device_release+0x8c/0xa0 kobject_put+0x8c/0x208 device_unregister+0x30/0x78 scmi_device_destroy+0x28/0x50 scmi_probe+0x354/0x5b0 platform_drv_probe+0x58/0xa8 really_probe+0x2c4/0x3e8 driver_probe_device+0x12c/0x148 __device_attach_driver+0xac/0x150 bus_for_each_drv+0x78/0xd8 __device_attach+0xe0/0x168 device_initial_probe+0x24/0x30 bus_probe_device+0xa0/0xa8 deferred_probe_work_func+0x8c/0xe0 process_one_work+0x1f0/0x478 worker_thread+0x22c/0x450 kthread+0x134/0x138 ret_from_fork+0x10/0x1c ---[ end trace 420bdb7f6af50937 ]--- Fix the issue by providing scmi_device_release callback. We have everything required for device release already in scmi_device_destroy, so we just need to move freeing of the device to scmi_device_release. Fixes: 933c5044 ("firmware: arm_scmi: add scmi protocol bus to enumerate protocol devices") Signed-off-by:
Sudeep Holla <sudeep.holla@arm.com> Cc: stable@vger.kernel.org # 4.17+ Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Bartosz Golaszewski authored
commit e3966a76 upstream. The timer interrupts specified in commit 3652e274 ("ARM: dts: da850: Add clocks") are wrong but since the current timer code hard-codes them, the bug was never spotted. This patch must go into stable since, once we introduce a proper clocksource driver, devices with buggy device tree will stop booting. Fixes: 3652e274 ("ARM: dts: da850: Add clocks") Cc: stable@vger.kernel.org Signed-off-by:
Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by:
Sekhar Nori <nsekhar@ti.com> Signed-off-by:
-
Marc Gonzalez authored
commit d0f9f167 upstream. Calling platform-specific code unconditionally blows up when running an ARCH_MULTIPLATFORM kernel on a different platform. Don't do it. Reported-by:
Paolo Pisati <p.pisati@gmail.com> Signed-off-by:
Marc Gonzalez <marc.w.gonzalez@free.fr> Acked-by:
Pavel Machek <pavel@ucw.cz> Cc: stable@vger.kernel.org # v4.8+ Fixes: a30eceb7 ("ARM: tango: add Suspend-to-RAM support") Signed-off-by:
-
Russell King authored
commit db409092 upstream. Booting 4.20 on a TheCUS N2100 results in a kernel oops while probing PCI, due to n2100_pci_map_irq() having been discarded during boot. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Cc: stable@vger.kernel.org # 2.6.18+ Signed-off-by:
-
Paul Burton authored
commit 67fc5dc8 upstream. When generating vdso-o32.lds & vdso-n32.lds for use with programs running as compat ABIs under 64b kernels, we previously haven't included the compiler flags that are supposedly common to all ABIs - ie. those in the ccflags-vdso variable. This is problematic in cases where we need to provide the -m%-float flag in order to ensure that we don't attempt to use a floating point ABI that's incompatible with the target CPU & ABI. For example a toolchain using current gcc trunk configured --with-fp-32=xx fails to build a 64r6el_defconfig kernel with the following error: cc1: error: '-march=mips1' requires '-mfp32' make[2]: *** [arch/mips/vdso/Makefile:135: arch/mips/vdso/vdso-o32.lds] Error 1 Include $(ccflags-vdso) for the compat VDSO .lds builds, just as it is included for the native VDSO .lds & when compiling objects for the compat VDSOs. This ensures we consistently provide the -msoft-float flag amongst others, avoiding the problem by ensuring we're agnostic to the toolchain defaults. Signed-off-by:
Paul Burton <paul.burton@mips.com> Fixes: ebb5e78c ("MIPS: Initial implementation of a VDSO") Cc: linux-mips@vger.kernel.org Cc: Kevin Hilman <khilman@baylibre.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Maciej W . Rozycki <macro@linux-mips.org> Cc: stable@vger.kernel.org # v4.4+ Signed-off-by:
-
Yifeng Li authored
commit 8a96669d upstream. On my Yeeloong 8089, I noticed the machine fails to shutdown properly, and often, the function mach_prepare_reboot() is unexpectedly executed, thus the machine reboots instead. A wait loop is needed to ensure the system is in a well-defined state before going down. In commit 997e93d4 ("MIPS: Hang more efficiently on halt/powerdown/restart"), a general superset of the wait loop for all platforms is already provided, so we don't need to implement our own. This commit simply removes the unreachable() compiler marco after mach_prepare_reboot(), thus allowing the execution of machine_hang(). My test shows that the machine is now able to shutdown successfully. Please note that there are two different bugs preventing the machine from shutting down, another work-in-progress commit is needed to fix a lockup in cpufreq / i8259 driver, please read Reference, this commit does not fix that bug. Reference: https://lkml.org/lkml/2019/2/5/908Signed-off-by:
Yifeng Li <tomli@tomli.me> Signed-off-by:
-
Paul Burton authored
commit 0648e50e upstream. The MIPS VDSO build currently doesn't provide the -msoft-float flag to the compiler as the kernel proper does. This results in an attempt to use the compiler's default floating point configuration, which can be problematic in cases where this is incompatible with the target CPU's -march= flag. For example decstation_defconfig fails to build using toolchains in which gcc was configured --with-fp-32=xx with the following error: LDS arch/mips/vdso/vdso.lds cc1: error: '-march=r3000' requires '-mfp32' make[2]: *** [scripts/Makefile.build:379: arch/mips/vdso/vdso.lds] Error 1 The kernel proper avoids this error because we build with the -msoft-float compiler flag, rather than using the compiler's default. Pass this flag through to the VDSO build so that it too becomes agnostic to the toolchain's floating point configuration. Note that this is filtered out from KBUILD_CFLAGS rather than simply always using -msoft-float such that if we switch the kernel to use -mno-float in the future the VDSO will automatically inherit the change. The VDSO doesn't actually include any floating point code, and its .MIPS.abiflags section is already manually generated to specify that it's compatible with any floating point ABI. As such this change should have no effect on the resulting VDSO, apart from fixing the build failure for affected toolchains. Signed-off-by:
Kevin Hilman <khilman@baylibre.com> Reported-by:
Guenter Roeck <linux@roeck-us.net> Tested-by:
-
Aaro Koskinen authored
commit dcf300a6 upstream. Don't set octeon_dma_bar_type if PCI is disabled. This avoids creation of the MSI irqchip later on, and saves a bit of memory. Signed-off-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by:
-
Vladimir Kondratiev authored
commit 05dc6001 upstream. Accordingly to the documentation ---cut--- The GCR_ERROR_CAUSE.ERR_TYPE field and the GCR_ERROR_MULT.ERR_TYPE fields can be cleared by either a reset or by writing the current value of GCR_ERROR_CAUSE.ERR_TYPE to the GCR_ERROR_CAUSE.ERR_TYPE register. ---cut--- Do exactly this. Original value of cm_error may be safely written back; it clears error cause and keeps other bits untouched. Fixes: 3885c2b4 ("MIPS: CM: Add support for reporting CM cache errors") Signed-off-by:
Vladimir Kondratiev <vladimir.kondratiev@linux.intel.com> Signed-off-by:
-
Andreas Ziegler authored
commit ea6eb5e7 upstream. The subsystem-specific message prefix for uprobes was also "trace_kprobe: " instead of "trace_uprobe: " as described in the original commit message. Link: http://lkml.kernel.org/r/20190117133023.19292-1-andreas.ziegler@fau.de Cc: Ingo Molnar <mingo@redhat.com> Cc: stable@vger.kernel.org Acked-by:
Masami Hiramatsu <mhiramat@kernel.org> Fixes: 72576341 ("tracing/probe: Show subsystem name in messages") Signed-off-by:
Andreas Ziegler <andreas.ziegler@fau.de> Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Dmitry Torokhov authored
commit e3f72b74 upstream. Well, hopefully 3rd time is a charm. We tried making that check DMI_BIOS_VERSION and DMI_BOARD_VERSION, but the real one is DMI_PRODUCT_VERSION. Fixes: 86c5dd68 ("pinctrl: cherryview: limit Strago DMI workarounds to version 1.0") Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=197953 Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1631930 Cc: stable@vger.kernel.org Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Chen-Yu Tsai authored
commit 10098709 upstream. The H6 main pin controller has four banks of interrupt-triggering pins. The driver as originally submitted only specified three, but had pin descriptions referencing a fourth bank. This results in a out-of-bounds access into .irq_array of struct sunxi_pinctrl. This however did not result in a crash until v4.20, with commit a66d9724 ("devres: Align data[] to ARCH_KMALLOC_MINALIGN"), which changed the alignment of memory region returned by devm_kcalloc(). The increase likely moved the out-of-bounds access into the next, unmapped page. With KASAN on, the bug is quite clear: BUG: KASAN: slab-out-of-bounds in sunxi_pinctrl_init_with_variant+0x49c/0x12b8 Write of size 4 at addr ffff80002c680280 by task swapper/0/1 CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.0.0-rc1-00016-gc480a5e6a077 #3 Hardware name: OrangePi Lite2 (DT) Call trace: dump_backtrace+0x0/0x220 show_stack+0x14/0x20 dump_stack+0xac/0xd4 print_address_description+0x60/0x25c kasan_report+0x14c/0x1ac __asan_store4+0x80/0xa0 sunxi_pinctrl_init_with_variant+0x49c/0x12b8 h6_pinctrl_probe+0x18/0x20 platform_drv_probe+0x6c/0xc8 really_probe+0x244/0x4b0 driver_probe_device.part.4+0x11c/0x164 __driver_attach+0x120/0x190 bus_for_each_dev+0xe8/0x158 driver_attach+0x30/0x40 bus_add_driver+0x308/0x318 driver_register+0xbc/0x1d0 __platform_driver_register+0x7c/0x88 h6_pinctrl_driver_init+0x18/0x20 do_one_initcall+0xd4/0x208 kernel_init_freeable+0x230/0x2c8 kernel_init+0x10/0x108 ret_from_fork+0x10/0x1c Allocated by task 1: kasan_kmalloc.part.0+0x4c/0x100 kasan_kmalloc+0xc4/0xe8 kasan_slab_alloc+0x14/0x20 __kmalloc_track_caller+0x130/0x238 devm_kmalloc+0x34/0xd0 sunxi_pinctrl_init_with_variant+0x1d8/0x12b8 h6_pinctrl_probe+0x18/0x20 platform_drv_probe+0x6c/0xc8 really_probe+0x244/0x4b0 driver_probe_device.part.4+0x11c/0x164 __driver_attach+0x120/0x190 bus_for_each_dev+0xe8/0x158 driver_attach+0x30/0x40 bus_add_driver+0x308/0x318 driver_register+0xbc/0x1d0 __platform_driver_register+0x7c/0x88 h6_pinctrl_driver_init+0x18/0x20 do_one_initcall+0xd4/0x208 kernel_init_freeable+0x230/0x2c8 kernel_init+0x10/0x108 ret_from_fork+0x10/0x1c Freed by task 0: (stack is not available) The buggy address belongs to the object at ffff80002c680080 which belongs to the cache kmalloc-512 of size 512 The buggy address is located 0 bytes to the right of 512-byte region [ffff80002c680080, ffff80002c680280) The buggy address belongs to the page: page:ffff7e0000b1a000 count:1 mapcount:0 mapping:ffff80002e00c780 index:0xffff80002c683c80 compound_mapcount: 0 flags: 0x10200(slab|head) raw: 0000000000010200 ffff80002e003a10 ffff80002e003a10 ffff80002e00c780 raw: ffff80002c683c80 0000000000100001 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff80002c680180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff80002c680200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff80002c680280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff80002c680300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff80002c680380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc Correct the number of IRQ banks so there are no more mismatches. Fixes: c8a83090 ("pinctrl: sunxi: add support for the Allwinner H6 main pin controller") Cc: <stable@vger.kernel.org> Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Tested-by:
Neil Armstrong <narmstrong@baylibre.com> Acked-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
-
Greg Kroah-Hartman authored
commit d88c93f0 upstream. debugfs_rename() needs to check that the dentries passed into it really are valid, as sometimes they are not (i.e. if the return value of another debugfs call is passed into this one.) So fix this up by properly checking if the two parent directories are errors (they are allowed to be NULL), and if the dentry to rename is not NULL or an error. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Tomas Winkler authored
commit c4a46acf upstream. The device was moved from misc device to character devices to support multiple mei devices. Cc: <stable@vger.kernel.org> #v4.9+ Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
-
Tomas Winkler authored
commit efe814e9 upstream. Add icelake mei device id. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Dan Carpenter authored
commit f8a70d8b upstream. The > comparison should be >= to prevent reading beyond the end of the func->template[] array. (The func->template array is allocated in vexpress_syscfg_regmap_init() and it has func->num_templates elements.) Fixes: 974cc7b9 ("mfd: vexpress: Define the device as MFD cells") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
-
Eric W. Biederman authored
commit 7146db33 upstream. Recently syzkaller was able to create unkillablle processes by creating a timer that is delivered as a thread local signal on SIGHUP, and receiving SIGHUP SA_NODEFERER. Ultimately causing a loop failing to deliver SIGHUP but always trying. When the stack overflows delivery of SIGHUP fails and force_sigsegv is called. Unfortunately because SIGSEGV is numerically higher than SIGHUP next_signal tries again to deliver a SIGHUP. From a quality of implementation standpoint attempting to deliver the timer SIGHUP signal is wrong. We should attempt to deliver the synchronous SIGSEGV signal we just forced. We can make that happening in a fairly straight forward manner by instead of just looking at the signal number we also look at the si_code. In particular for exceptions (aka synchronous signals) the si_code is always greater than 0. That still has the potential to pick up a number of asynchronous signals as in a few cases the same si_codes that are used for synchronous signals are also used for asynchronous signals, and SI_KERNEL is also included in the list of possible si_codes. Still the heuristic is much better and timer signals are definitely excluded. Which is enough to prevent all known ways for someone sending a process signals fast enough to cause unexpected and arguably incorrect behavior. Cc: stable@vger.kernel.org Fixes: a27341cd ("Prioritize synchronous signals over 'normal' signals") Tested-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Eric W. Biederman authored
commit 35634ffa upstream. Recently syzkaller was able to create unkillablle processes by creating a timer that is delivered as a thread local signal on SIGHUP, and receiving SIGHUP SA_NODEFERER. Ultimately causing a loop failing to deliver SIGHUP but always trying. Upon examination it turns out part of the problem is actually most of the solution. Since 2.5 signal delivery has found all fatal signals, marked the signal group for death, and queued SIGKILL in every threads thread queue relying on signal->group_exit_code to preserve the information of which was the actual fatal signal. The conversion of all fatal signals to SIGKILL results in the synchronous signal heuristic in next_signal kicking in and preferring SIGHUP to SIGKILL. Which is especially problematic as all fatal signals have already been transformed into SIGKILL. Instead of dequeueing signals and depending upon SIGKILL to be the first signal dequeued, first test if the signal group has already been marked for death. This guarantees that nothing in the signal queue can prevent a process that needs to exit from exiting. Cc: stable@vger.kernel.org Tested-by:
-
Dan Murphy authored
commit f214ff52 upstream. Per Jonathan Cameron, the buffer needs to allocate room for a 64 bit timestamp as well as the channels. Change the buffer to allocate this additional space. Fixes: 2a864877 ("iio: adc: ti-ads8688: add trigger and buffer support") Signed-off-by:
Dan Murphy <dmurphy@ti.com> Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Matt Ranostay authored
commit 0808831d upstream. IIO_TEMP scale value for temperature was incorrect and not in millicelsius as required by the ABI documentation. Signed-off-by:
Matt Ranostay <matt.ranostay@konsulko.com> Fixes: 27dec00e (iio: chemical: add Atlas pH-SM sensor support) Cc: <stable@vger.kernel.org> Signed-off-by:
-
Hans de Goede authored
commit 9bcf15f7 upstream. Prior to this commit there were 3 issues with our handling of the TS-pin: 1) There are 2 ways how the firmware can disable monitoring of the TS-pin for designs which do not have a temperature-sensor for the battery: a) Clearing bit 0 of the AXP20X_ADC_EN1 register b) Setting bit 2 of the AXP288_ADC_TS_PIN_CTRL monitoring Prior to this commit we were unconditionally setting both bits to the value used on devices with a TS. This causes the temperature protection to kick in on devices without a TS, such as the Jumper ezbook v2, causing them to not charge under Linux. This commit fixes this by using regmap_update_bits when updating these 2 registers, leaving the 2 mentioned bits alone. The next 2 problems are related to our handling of the current-source for the TS-pin. The current-source used for the battery temp-sensor (TS) is shared with the GPADC. For proper fuel-gauge and charger operation the TS current-source needs to be permanently on. But to read the GPADC we need to temporary switch the TS current-source to ondemand, so that the GPADC can use it, otherwise we will always read an all 0 value. 2) Problem 2 is we were writing hardcoded values to the ADC TS pin-ctrl register, overwriting various other unrelated bits. Specifically we were overwriting the current-source setting for the TS and GPIO0 pins, forcing it to 80ųA independent of its original setting. On a Chuwi Vi10 tablet this was causing us to get a too high adc value (due to a too high current-source) resulting in the following errors being logged: ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion] ACPI Error: Method parse/execution failed \_SB.SXP1._TMP, AE_ERROR This commit fixes this by using regmap_update_bits to change only the relevant bits. 3) After reading the GPADC channel we were unconditionally enabling the TS current-source even on devices where the TS-pin is not used and the current-source thus was off before axp288_adc_read_raw call. This commit fixes this by making axp288_adc_set_ts a nop on devices where the ADC is not enabled for the TS-pin. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1610545 Fixes: 3091141d ("iio: adc: axp288: Fix the GPADC pin ...") Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Cc: <Stable@vger.kernel.org> Signed-off-by:
-
Martin Kelly authored
commit b119d3bc upstream. Currently, num_loops is unsigned, but it's set by strtoll, which returns a (signed) long long int. This could lead to overflow, and it also makes the check "num_loops < 0" always be false, since num_loops is unsigned. Setting num_loops to -1 to loop forever is almost working because num_loops is getting set to a very high number, but it's technically still incorrect. Fix this issue by making num_loops signed. This also fixes an error found by Smatch. Signed-off-by:
Martin Kelly <mkelly@xevo.com> Reported-by:
-
