In rare circumstances, a descriptor writeback flush may not work if it
arrives on a specific clock cycle as a writeback request is going out.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When the adapter is closed while it is simultaneously going through a
reset, it can cause a null-pointer dereference when the two different code
paths simultaneously cleanup up the Tx/Rx resources.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix up code so that changes in DCB settings
are detected only when ixgbe_dcbnl_set_all is called.
Previously, a series of 'change' commands followed by
a call to ixgbe_dcbnl_set_all() would always be handled
as a HW change - even if the net change was zero.
This patch checks for this case of no actual change and
skips going through the HW set process.

Without this fix, the link could reset and result in
a link flap.

The core change in this patch is to check for changes
in the ixgbe_copy_dcb_cfg() routine - and return
a bitmask of detected changes.  The other
places where changes were detected previously can be removed.
Signed-off-by: Eric Multanen <eric.w.multanen@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Now the helper function from filter.c for negative offsets is exported,
it can be used it in the jit to handle negative offsets.

First modify the asm load helper functions to handle:
- know positive offsets
- know negative offsets
- any offset

then the compiler can be modified to explicitly use these helper
when appropriate.

This fixes the case of a negative X register and allows to lift
the restriction that bpf programs with negative offsets can't
be jited.
Signed-of-by: Jan Seiffert <kaffeemonster@googlemail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function is renamed to make it a little more clear what it does.
It is not added to any .h because it is not for general consumption, only for
bpf internal use (and so by the jits).
Signed-of-by: Jan Seiffert <kaffeemonster@googlemail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The explanation of ip_local_port_range in
Documentation/networking/ip-sysctl.txt contains several factual
errors:

- The default value of ip_local_port_range does not depend on the
  amount of memory available in the system.
- tcp_tw_recycle is not enabled by default.
- 1024-4999 is not the default value.
- Etc.

Clean up the mess.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmsplice()/splice(pipe, socket) call do_tcp_sendpages() one page at a
time, adding at most 4096 bytes to an skb. (assuming PAGE_SIZE=4096)

The call to tcp_push() at the end of do_tcp_sendpages() forces an
immediate xmit when pipe is not already filled, and tso_fragment() try
to split these skb to MSS multiples.

4096 bytes are usually split in a skb with 2 MSS, and a remaining
sub-mss skb (assuming MTU=1500)

This makes slow start suboptimal because many small frames are sent to
qdisc/driver layers instead of big ones (constrained by cwnd and packets
in flight of course)

In fact, applications using sendmsg() (adding an additional memory copy)
instead of vmsplice()/splice()/sendfile() are a bit faster because of
this anomaly, especially if serving small files in environments with
large initial [c]wnd.

Call tcp_push() only if MSG_MORE is not set in the flags parameter.

This bit is automatically provided by splice() internals but for the
last page, or on all pages if user specified SPLICE_F_MORE splice()
flag.

In some workloads, this can reduce number of sent logical packets by an
order of magnitude, making zero-copy TCP actually faster than
one-copy :)
Reported-by: Tom Herbert <therbert@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail&gt;com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For every transmitted packet, ppp_start_xmit() will stop the netdev
queue and then, if appropriate, restart it. This causes the TX softirq
to run, entirely gratuitously.

This is "only" a waste of CPU time in the normal case, but it's actively
harmful when the PPP device is a TEQL slave — the wakeup will cause the
offending device to receive the next TX packet from the TEQL queue, when
it *should* have gone to the next slave in the list. We end up seeing
large bursts of packets on just *one* slave device, rather than using
the full available bandwidth over all slaves.

This patch fixes the problem by *not* unconditionally stopping the queue
in ppp_start_xmit(). It adds a return value from ppp_xmit_process()
which indicates whether the queue should be stopped or not.

It *doesn't* remove the call to netif_wake_queue() from
ppp_xmit_process(), because other code paths (especially from
ppp_output_wakeup()) need it there and it's messy to push it out to the
other callers to do it based on the return value. So we leave it in
place — it's a no-op in the case where the queue wasn't stopped, so it's
harmless in the TX path.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit f04565dd (dev: use name hash for dev_seq_ops) added a second
regression, as some devices are missing from /proc/net/dev if many
devices are defined.

When seq_file buffer is filled, the last ->next/show() method is
canceled (pos value is reverted to value prior ->next() call)

Problem is after above commit, we dont restart the lookup at right
position in ->start() method.

Fix this by removing the internal 'pos' pointer added in commit, since
we need to use the 'loff_t *pos' provided by seq_file layer.

This also reverts commit 5cac98dd (net: Fix corruption
in /proc/*/net/dev_mcast), since its not needed anymore.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Mihai Maruseac <mmaruseac@ixiacom.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull drm update from Dave Airlie:
 "This pull just contains a forward of the Intel fixes from Daniel.

  The only annoyance is the RC6 enable, which really should have made
  -next, but since Ubuntu are shipping it I reckon its getting a good
  testing now by the time 3.4 comes out.

  The pull from Daniel contains his pull message to me:

    "A few patches for 3.4, major part is 3 regression fixes:
     - ppgtt broke hibernate on snb/ivb.  Somehow our QA claims that it
       still works, which is why this has not been caught earlier.
     - ppgtt flails in combination with dmar.  I kinda expected this one :(
     - fence handling bugfix for gen2/3.  Iirc this one is about a year
       old, fix curtesy Chris Wilson.  I've created an shockingly simple
       i-g-t test to catch this in the future."

     Wrt regressions I've just got a report that gmbus (newly enabled
     again in 3.4) is a bit noisy.  I'm looking into this atm.

     Also included are the rc6 enable patches for snb from Eugeni.  I
     wanted to include these in the main 3.4 pull but screwed it up.
     Please hit me.  Imo these kind of patches really should go in
     before -rc1, but in thise case rc6 has brought us tons of press and
     guinea pigs^W^W testers and ubuntu is already running with it.  So
     I estimate a pretty small chance for this to blow up.

     And some smaller things:
      - two minor locking snafus
      - server gt2 ivb pciid
      - 2 patches to sanitize the register state left behind by the bios
        some more
      - 2 new quirk entries
      - cs readback trick against missed IRQs from ivb also enabled on snb
      - sprite fix from Jesse"

Let's see if the "enable RC6 on sandybridge" finally works and sticks.
I've been enabling it by hand (i915.i915_enable_rc6=1) for several
months on my Macbook Air, and it definitely makes a difference (and has
worked for me).  But every time we enabled it before it showed some odd
hw buglet for *somebody*.

This time it's all good, I'm sure.

* 'drm-fixes-intel' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: treat src w & h as fixed point in sprite handling code
  drm/i915: no-lvds quirk on MSI DC500
  drm/i915: Add lock on drm_helper_resume_force_mode
  drm/i915: don't leak struct_mutex lock on ppgtt init failures
  drm/i915: disable ppgtt on snb when dmar is enabled
  drm/i915: add Ivy Bridge GT2 Server entries
  drm/i915: properly clear SSC1 bit in the pch refclock init code
  drm/i915: apply CS reg readback trick against missed IRQ on snb
  drm/i915: quirk away broken OpRegion VBT
  drm/i915: enable plain RC6 on Sandy Bridge by default
  drm/i915: allow to select rc6 modes via kernel parameter
  drm/i915: Mark untiled BLT commands as fenced on gen2/3
  drm/i915: properly restore the ppgtt page directory on resume
  drm/i915: Sanitize BIOS debugging bits from PIPECONF

Pull drm fixes from Dave Airlie:
 "Mainly nouveau fixes, one for a regressions in -rc1, fixes for booting
  on a ppc G5, and a Kconfig fix.  Two radeon fixes, one oops, one s/r
  fix.  One udl mmap fix.  And one core drm fix to stop bad fbdev apps
  overwriting bits of ram."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: Validate requested virtual size against allocated fb size
  drm/radeon: Don't dereference possibly-NULL pointer.
  mm, drm/udl: fixup vma flags on mmap
  drm/radeon/kms: fix fans after resume
  nouveau/bios: Fix tracking of BIOS image data
  nouveau: Fix crash when pci_ram_rom() returns a size of 0
  drm/nouveau: select POWER_SUPPLY
  drm/nouveau: inform userspace of relaxed kernel subchannel requirements
  Revert "drm/nouveau: inform userspace of new kernel subchannel requirements"
  drm/nouveau: oops, create m2mf for nvd9 too

Pull arch/microblaze fixes from Michal Simek.

* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Fix ret_from_fork declaration
  microblaze: Do not use tlb_skip in early_printk
  microblaze: Add missing headers caused by disintegration asm/system.h
  microblaze: Fix stack usage in PAGE_SIZE copy_tofrom_user
  microblaze: Fix tlb_skip variable on noMMU system
  microblaze: Fix __futex_atomic_op macro register usage

Pull m68k fixes from Geert Uytterhoeven:
 "Here are a few fixes for the m68k architecture.  Nothing fancy this
  time, just a build fix for the asm/system.h disintegration, and two
  fixes for missing platform checks (one got in during last merge
  window), which can cause crashes in multi-platform kernels."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k/q40: Add missing platform check before registering platform devices
  m68k/mac: Add missing platform check before registering platform devices
  m68k: include asm/cmpxchg.h in our m68k atomic.h

Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-intel-fixes

From Daniel Vetter:

"A few patches for 3.4, major part is 3 regression fixes:
- ppgtt broke hibernate on snb/ivb. Somehow our QA claims that it still
 works, which is why this has not been caught earlier.
- ppgtt flails in combination with dmar. I kinda expected this one :(
- fence handling bugfix for gen2/3. Iirc this one is about a year old, fix
 curtesy Chris Wilson. I've created an shockingly simple i-g-t test to
 catch this in the future.

Wrt regressions I've just got a report that gmbus (newly enabled again in
3.4) is a bit noisy. I'm looking into this atm.

Also included are the rc6 enable patches for snb from Eugeni. I wanted to
include these in the main 3.4 pull but screwed it up. Please hit me. Imo
these kind of patches really should go in before -rc1, but in thise case
rc6 has brought us tons of press and guinea pigs^W^W testers and ubuntu is
already running with it. So I estimate a pretty small chance for this to
blow up.

And some smaller things:
- two minor locking snafus
- server gt2 ivb pciid
- 2 patches to sanitize the register state left behind by the bios some
 more
- 2 new quirk entries
- cs readback trick against missed IRQs from ivb also enabled on snb
- sprite fix from Jesse"

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: treat src w & h as fixed point in sprite handling code
  drm/i915: no-lvds quirk on MSI DC500
  drm/i915: Add lock on drm_helper_resume_force_mode
  drm/i915: don't leak struct_mutex lock on ppgtt init failures
  drm/i915: disable ppgtt on snb when dmar is enabled
  drm/i915: add Ivy Bridge GT2 Server entries
  drm/i915: properly clear SSC1 bit in the pch refclock init code
  drm/i915: apply CS reg readback trick against missed IRQ on snb
  drm/i915: quirk away broken OpRegion VBT
  drm/i915: enable plain RC6 on Sandy Bridge by default
  drm/i915: allow to select rc6 modes via kernel parameter
  drm/i915: Mark untiled BLT commands as fenced on gen2/3
  drm/i915: properly restore the ppgtt page directory on resume
  drm/i915: Sanitize BIOS debugging bits from PIPECONF

mplayer -vo fbdev tries to create a screen that is twice as tall as the
allocated framebuffer for "doublebuffering". By default, and all in-tree
users, only sufficient memory is allocated and mapped to satisfy the
smallest framebuffer and the virtual size is no larger than the actual.
For these users, we should therefore reject any userspace request to
create a screen that requires a buffer larger than the framebuffer
originally allocated.

References: https://bugs.freedesktop.org/show_bug.cgi?id=38138Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

This was missed when we converted the source values to 16.16 fixed point.

Cc: stable@vger.kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This hardware doesn't have an LVDS, it's a desktop box. Fix incorrect
LVDS detection.

Cc: stable@kernel.org
Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

i915_drm_thaw was not locking the mode_config lock when calling
drm_helper_resume_force_mode. When there were multiple wake sources,
this caused FDI training failure on SNB which in turn corrupted the
display.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Reported-by: Konstantin Belousov <kostikbel@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Pull dma-buf prime support from Dave Airlie:
 "This isn't a majorly urgent thing to have, but we'd like to set the
  stage for working on dma-buf support in the drm drivers for the next
  merge window, so I'd like to push in the initial submission now so
  people have something that we can build on top of.  The code just
  introduces the user interface and internal helper functions for
  drivers to use.

  We have driver support under development for i915, nouveau, udl on x86
  and exynos, omapdrm on arm, which we would be aiming for the next
  merge window."

In the -rc1 announcement I asked for people who would use this to
comment on it, and got severa "Yes please" from people for this and for
HSI (that I merged earlier).

So far crickets on pohmelfs and the DMA-mapping infrastructure.

* 'drm-prime-dmabuf-initial' of git://people.freedesktop.org/~airlied/linux:
  drm: base prime/dma-buf support (v5)

Pull networking fixes from David Miller:

 1) Provide device string properly for USB i2400m wimax devices, also
    don't OOPS when providing firmware string.  From Phil Sutter.

 2) Add support for sh_eth SH7734 chips, from Nobuhiro Iwamatsu.

 3) Add another device ID to USB zaurus driver, from Guan Xin.

 4) Loop index start in pool vector iterator is wrong causing MAC to not
    get configured in bnx2x driver, fix from Dmitry Kravkov.

 5) EQL driver assumes HZ=100, fix from Eric Dumazet.

 6) Now that skb_add_rx_frag() can specify the truesize increment
    separately, do so in f_phonet and cdc_phonet, also from Eric
    Dumazet.

 7) virtio_net accidently uses net_ratelimit() not only on the kernel
    warning but also the statistic bump, fix from Rick Jones.

 8) ip_route_input_mc() uses fixed init_net namespace, oops, use
    dev_net(dev) instead.  Fix from Benjamin LaHaise.

 9) dev_forward_skb() needs to clear the incoming interface index of the
    SKB so that it looks like a new incoming packet, also from Benjamin
    LaHaise.

10) iwlwifi mistakenly initializes a channel entry as 2GHZ instead of
    5GHZ, fix from Stanislav Yakovlev.

11) Missing kmalloc() return value checks in orinoco, from Santosh
    Nayak.

12) ath9k doesn't check for HT capabilities in the right way, it is
    checking ht_supported instead of the ATH9K_HW_CAP_HT flag.  Fix from
    Sujith Manoharan.

13) Fix x86 BPF JIT emission of 16-bit immediate field of AND
    instructions, from Feiran Zhuang.

14) Avoid infinite loop in GARP code when registering sysfs entries.
    From David Ward.

15) rose protocol uses memcpy instead of memcmp in a device address
    comparison, oops.  Fix from Daniel Borkmann.

16) Fix build of lpc_eth due to dev_hw_addr_rancom() interface being
    renamed to eth_hw_addr_random().  From Roland Stigge.

17) Make ipv6 RTM_GETROUTE interpret RTA_IIF attribute the same way
    that ipv4 does.  Fix from Shmulik Ladkani.

18) via-rhine has an inverted bit test, causing suspend/resume
    regressions.  Fix from Andreas Mohr.

19) RIONET assumes 4K page size, fix from Akinobu Mita.

20) Initialization of imask register in sky2 is buggy, because bits are
    "or'd" into an uninitialized local variable.  Fix from Lino
    Sanfilippo.

21) Fix FCOE checksum offload handling, from Yi Zou.

22) Fix VLAN processing regression in e1000, from Jiri Pirko.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
  sky2: dont overwrite settings for PHY Quick link
  tg3: Fix 5717 serdes powerdown problem
  net: usb: cdc_eem: fix mtu
  net: sh_eth: fix endian check for architecture independent
  usb/rtl8150 : Remove duplicated definitions
  rionet: fix page allocation order of rionet_active
  via-rhine: fix wait-bit inversion.
  ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4
  net: lpc_eth: Fix rename of dev_hw_addr_random
  net/netfilter/nfnetlink_acct.c: use linux/atomic.h
  rose_dev: fix memcpy-bug in rose_set_mac_address
  Fix non TBI PHY access; a bad merge undid bug fix in a previous commit.
  net/garp: avoid infinite loop if attribute already exists
  x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND
  bonding: emit event when bonding changes MAC
  mac80211: fix oper channel timestamp updation
  ath9k: Use HW HT capabilites properly
  MAINTAINERS: adding maintainer for ipw2x00
  net: orinoco: add error handling for failed kmalloc().
  net/wireless: ipw2x00: fix a typo in wiphy struct initilization
  ...

This patch corrects a bug in function sky2_open() of the Marvell Yukon 2 driver
in which the settings for PHY quick link are overwritten.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Stephen Hemminger <shemminger@vyattta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This merges some of the fixes from Paul Gortmaker for the header file
cleanup fallout.

Some of the patches are going through arch maintainer trees, and David
Howells suggested another be done differently, but this at least fixes a
few cases.

* emailed from Paul Gortmaker <paul.gortmaker@windriver.com>:
  asm-generic: add linux/types.h to cmpxchg.h
  firewire: restore the device.h include in linux/firewire.h
  frv: fix warnings in mb93090-mb00/pci-dma.c about implicit EXPORT_SYMBOL
  parisc: fix missing cmpxchg file error from system.h split
  blackfin: fix cmpxchg build fails from system.h fallout
  avr32: fix build failures from mis-naming of atmel_nand.h
  ARM: mach-msm: fix compile fail from system.h fallout
  irq_work: fix compile failure on MIPS from system.h split

If port 0 of a 5717 serdes device powers down, it hides the phy from
port 1.  This patch works around the problem by keeping port 0's phy
powered up.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Builds of the openrisc or1ksim_defconfig show the following:

  In file included from arch/openrisc/include/generated/asm/cmpxchg.h:1:0,
                   from include/asm-generic/atomic.h:18,
                   from arch/openrisc/include/generated/asm/atomic.h:1,
                   from include/linux/atomic.h:4,
                   from include/linux/dcache.h:4,
                   from fs/notify/fsnotify.c:19:
  include/asm-generic/cmpxchg.h: In function '__xchg':
  include/asm-generic/cmpxchg.h:34:20: error: expected ')' before 'u8'
  include/asm-generic/cmpxchg.h:34:20: warning: type defaults to 'int' in type name

and many more lines of similar errors.  It seems specific to the or32
because most other platforms have an arch specific component that would
have already included types.h ahead of time, but the o32 does not.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Howells <dhowells@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 313162d0 ("device.h: audit and cleanup users in main include
dir") exchanged an include <linux/device.h> for a struct *device but in
actuality I misread this file when creating 313162d0 and it should have
remained an include.

There were no build regressions since all consumers were already getting
device.h anyway, but make it right regardless.
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

To fix:

    arch/frv/mb93090-mb00/pci-dma.c:31:1: warning: data definition has no type or storage class [enabled by default]
    arch/frv/mb93090-mb00/pci-dma.c:31:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
    arch/frv/mb93090-mb00/pci-dma.c:31:1: warning: parameter names (without types) in function declaration [enabled by default]
    arch/frv/mb93090-mb00/pci-dma.c:38:1: warning: data definition has no type or storage class [enabled by default]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit b4816afa ("Move the asm-generic/system.h xchg()
implementation to asm-generic/cmpxchg.h") introduced the concept of
asm/cmpxchg.h but the parisc arch never got one.  Fork the cmpxchg
content out of the asm/atomic.h file to create one.

Some minor whitespace fixups were done on the block of code that created
the new file.

Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 3bed8d67 ("Disintegrate asm/system.h for Blackfin [ver #2]")
introduced arch/blackfin/include/asm/cmpxchg.h but has it also including
the asm-generic one which causes this:

  CC      arch/blackfin/kernel/asm-offsets.s
  In file included from arch/blackfin/include/asm/cmpxchg.h:125:0,
                 from arch/blackfin/include/asm/atomic.h:10,
                 from include/linux/atomic.h:4,
                 from include/linux/spinlock.h:384,
                 from include/linux/seqlock.h:29,
                 from include/linux/time.h:8,
                 from include/linux/timex.h:56,
                 from include/linux/sched.h:57,
                 from arch/blackfin/kernel/asm-offsets.c:10:
  include/asm-generic/cmpxchg.h:24:15: error: redefinition of '__xchg'
  arch/blackfin/include/asm/cmpxchg.h:82:29: note: previous definition of '__xchg' was here
  make[2]: *** [arch/blackfin/kernel/asm-offsets.s] Error 1

It really only needs two simple defines from asm-generic, so just use
those instead.

Cc: Bob Liu <lliubbo@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit bf4289cb ("ATMEL: fix nand ecc support") indicated that it
wanted to "Move platform data to a common header
include/linux/platform_data/atmel_nand.h" and the new header even had
re-include protectors with:

    #ifndef __ATMEL_NAND_H__

However, the file that was added was simply called atmel.h
and this caused avr32 defconfig to fail with:

  In file included from arch/avr32/boards/atstk1000/setup.c:22:
  arch/avr32/mach-at32ap/include/mach/board.h:10:44: error: linux/platform_data/atmel_nand.h: No such file or directory
  In file included from arch/avr32/boards/atstk1000/setup.c:22:
  arch/avr32/mach-at32ap/include/mach/board.h:121: warning: 'struct atmel_nand_data' declared inside parameter list
  arch/avr32/mach-at32ap/include/mach/board.h:121: warning: its scope is only this definition or declaration, which is probably not what you want
  make[2]: *** [arch/avr32/boards/atstk1000/setup.o] Error 1

It seems the scope of the file contents will expand beyond
just nand, so ignore the original intention, and fix up the
users who reference the bad name with the _nand suffix.

CC: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
CC: David Woodhouse <dwmw2@infradead.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

To fix:

  In file included from arm/boot/compressed/misc.c:28:0:
  arm/mach-msm/include/mach/uncompress.h: In function 'putc':
  arch/arm/mach-msm/include/mach/uncompress.h:48:3: error: implicit
  declaration of function 'smp_mb' [-Werror=implicit-function-declaration]

The putc does a cpu_relax which for this platform is smp_mb.

Bisect indicates the 1st failing commit as: 0195c002 ("Merge tag
'split-asm_system_h...")
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull HSI (High Speed Synchronous Serial Interface) framework from Carlos Chinea:
 "The High Speed Synchronous Serial Interface (HSI) is a serial
  interface mainly used for connecting application engines (APE) with
  cellular modem engines (CMT) in cellular handsets.

  The framework is currently being used for some people and we would
  like to see it integrated into the kernel for 3.3.  There is no HW
  controller drivers in this pull, but some people have already some of
  them pending which they would like to push as soon as this integrated.
  I am also working on the acceptance for an TI OMAP one, based on a
  compatible legacy version of the interface called SSI."

Ok, so it didn't get into 3.3, but here it is pulled into 3.4.

Several people piped up to say "yeah, we want this".

* 'for-next' of git://gitorious.org/kernel-hsi/kernel-hsi:
  HSI: hsi_char: Update ioctl-number.txt
  HSI: Add HSI API documentation
  HSI: hsi_char: Add HSI char device kernel configuration
  HSI: hsi_char: Add HSI char device driver
  HSI: hsi: Introducing HSI framework

Pull 'make cscope' fix from Michal Marek:
 "The kbuild.git#misc pull request introduced a bug that broke make
  cscope.  Apparently, both the original author and me only tested the
  use case that the commit was supposed to improve (make tags/TAGS), and
  not the use case that was not supposed (make cscope)."

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  tags.sh: Add missing quotes

Pull crypto fixes from Herbert Xu:
 - Fix for CPU hotplug hang in padata.
 - Avoid using cpu_active inappropriately in pcrypt and padata.
 - Fix for user-space algorithm lookup hang with IV generators.
 - Fix for netlink dump of algorithms where stuff went missing due to
   incorrect calculation of message size.

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: user - Fix size of netlink dump message
  crypto: user - Fix lookup of algorithms with IV generator
  crypto: pcrypt - Use the online cpumask as the default
  padata: Fix cpu hotplug
  padata: Use the online cpumask as the default
  padata: Add a reference to the api documentation

Pull powerpc fixes from Benjamin Herrenschmidt:
 "This contains a couple more fixes for the system.h disintegration, a
  trivial section mismatch fix, a couple of patches from akpm that I
  didn't quite get he expected me to pickup, and a few more trivialities
  form Kumar that he appear to have forgotten to send me in the previous
  batch."

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/eeh: Fix use of set_current_state() in eeh event handling set_current_state() wart
  powerpc/eeh: Remove eeh_event_handler()->daemonize()
  powerpc/kvm: Fallout from system.h disintegration
  powerpc: Fix fallout from system.h split up
  powerpc: Mark const init data with __initconst instead of __initdata
  powerpc/qe: Update the SNUM table for MPC8569 Rev2.0
  powerpc/dts: Removed fsl,msi property from dts.
  powerpc/epapr: add "memory" as a clobber to all hypercalls
  powerpc/85xx: Enable I2C_CHARDEV and I2C_MPC options in defconfigs
  powerpc/85xx: add the P1020UTM-PC DTS support
  powerpc/85xx: add the P1020MBG-PC DTS support
  powerpc/8xxx: remove 85xx/86xx restrictions from fsl_guts.h

Pull cpumask cleanups from Rusty Russell:
 "(Somehow forgot to send this out; it's been sitting in linux-next, and
  if you don't want it, it can sit there another cycle)"

I'm a sucker for things that actually delete lines of code.

Fix up trivial conflict in arch/arm/kernel/kprobes.c, where Rusty fixed
a user of &cpu_online_map to be cpu_online_mask, but that code got
deleted by commit b21d55e9 ("ARM: 7332/1: extract out code patch
function from kprobes").

* tag 'for-linus' of git://github.com/rustyrussell/linux:
  cpumask: remove old cpu_*_map.
  documentation: remove references to cpu_*_map.
  drivers/cpufreq/db8500-cpufreq: remove references to cpu_*_map.
  remove references to cpu_*_map in arch/

Builds of the MIPS platform ip32_defconfig fails as of commit
0195c002 ("Merge tag 'split-asm_system_h ...") because MIPS xchg()
macro uses BUILD_BUG_ON and it was moved in commit b81947c6
("Disintegrate asm/system.h for MIPS").

The root cause is that the system.h split wasn't tested on a baseline
with commit 6c03438e ("kernel.h: doesn't explicitly use bug.h, so
don't include it.")

Since this file uses BUG code in several other places besides the xchg
call, simply make the inclusion explicit.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Totally unexpected that this regressed. Luckily it sounds like we just
need to have dmar disable on the igfx, not the entire system. At least
that's what a few days of testing between Tony Vroon and me indicates.
Reported-by: Tony Vroon <tony@linx.net>
Cc: Tony Vroon <tony@linx.net>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43024Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This adds PCI ID for IVB GT2 server variant which we were missing.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: fix up conflict because the patch has been diffed against next. tsk.]
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>