- 20 Aug, 2019 15 commits
-
-
Maxime Ripard authored
The two main generations of our I2S controller require a slightly different format configuration, mostly because of a quite different register layout and some additional registers being needed on the newer generation. This used to be controlled through a bunch of booleans, however this proved to be quite impractical, especially since a bunch of SoCs forgot to set those parameters and therefore were broken from that point of view. Fixes: 21faaea1 ("ASoC: sun4i-i2s: Add support for A83T") Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Link: https://lore.kernel.org/r/dc818644c3e40734e7a97247c994b1fca1c3c047.1566242458.git-series.maxime.ripard@bootlin.comSigned-off-by:
Mark Brown <broonie@kernel.org>
-
Maxime Ripard authored
The two main generations of our I2S controller require a slightly different channel configuration, mostly because of a quite different register layout and some additional registers being needed on the newer generation. This used to be controlled through a bunch of booleans, however this proved to be quite impractical, especially since a bunch of SoCs forgot to set those parameters and therefore were broken from that point of view. Fixes: 21faaea1 ("ASoC: sun4i-i2s: Add support for A83T") Signed-off-by:
-
Mark Brown authored
-
Daniel Stuart authored
Every single baytrail chromebook sets PMC to 0, as can be seeing below by searching through coreboot source code: $ grep -rl "PMC_PLT_CLK\[0\]" . ./rambi/variants/glimmer/devicetree.cb ./rambi/variants/clapper/devicetree.cb ./rambi/variants/swanky/devicetree.cb ./rambi/variants/enguarde/devicetree.cb ./rambi/variants/winky/devicetree.cb ./rambi/variants/kip/devicetree.cb ./rambi/variants/squawks/devicetree.cb ./rambi/variants/orco/devicetree.cb ./rambi/variants/ninja/devicetree.cb ./rambi/variants/heli/devicetree.cb ./rambi/variants/sumo/devicetree.cb ./rambi/variants/banjo/devicetree.cb ./rambi/variants/candy/devicetree.cb ./rambi/variants/gnawty/devicetree.cb ./rambi/variants/rambi/devicetree.cb ./rambi/variants/quawks/devicetree.cb Plus, Cyan (only non-baytrail chromebook with max98090) also needs this patch for audio to work. Thus, this commit adds all the missing devices to bsw_max98090 quirk table, implemented by commit a182ecd3 ("ASoC: intel: cht_bsw_max98090_ti: Add quirk for boards using pmc_plt_clk_0"). Signed-off-by:
Daniel Stuart <daniel.stuart14@gmail.com> Link: https://lore.kernel.org/r/20190815171300.30126-1-daniel.stuart14@gmail.comSigned-off-by:
-
Maxime Ripard authored
The MCLK divider calculation is currently computing the ideal divider using the oversample rate, the sample rate and the parent rate. However, since we have access to the frequency is supposed to be running at already, and as it turns out we're using it to compute the oversample rate, we can just use the ratio between the parent rate and the MCLK rate to simplify a bit the formula. Signed-off-by:
-
Maxime Ripard authored
The sun4i_i2s_hw_params already has a variable holding the value returned by params_channels, so let's just use that variable instead of calling params_channels multiple times. Signed-off-by:
-
Maxime Ripard authored
The BCLK divider should be calculated using the parameters that actually make the BCLK rate: the number of channels, the sampling rate and the sample width. We've been using the oversample_rate previously because in the former SoCs, the BCLK's parent is MCLK, which in turn is being used to generate the oversample rate, so we end up with something like this: oversample = mclk_rate / sampling_rate bclk_div = oversample / word_size / channels So, bclk_div = mclk_rate / sampling_rate / word_size / channels. And this is actually better, since the oversampling ratio only plays a role because the MCLK is its parent, not because of what BCLK is supposed to be. Furthermore, that assumption of MCLK being the parent has been broken on newer SoCs, so let's use the proper formula, and have the parent rate as an argument. Fixes: 7d299381 ("ASoC: sun4i-i2s: Add support for H3") Fixes: 21faaea1 ("ASoC: sun4i-i2s: Add support for A83T") Fixes: 66ecce33 ("ASoC: sun4i-i2s: Add compatibility with A64 codec I2S") Signed-off-by:
-
Maxime Ripard authored
Since the introduction of the driver, a new managed helper for the dmaengine PCM registration has been created. Let's use it to simplify a bit our probe and remove functions. Signed-off-by:
-
Maxime Ripard authored
So far the regmap and the dmaengine PCM are registered after our component has been, which means that our driver isn't properly initialised by then. Let's fix that. Signed-off-by:
-
Michał Mirosław authored
Make '* Capture Mode' a mux. This makes DAPM know that in single-ended mode only inverting mux paths need to be enabled. Signed-off-by:
Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/125cd3c9f298da9b08a4d6002d4c00d70a898950.1566298834.git.mirq-linux@rere.qmqm.plSigned-off-by:
-
Michał Mirosław authored
Trivial fix for typo in "Capture Inverting Mux"es' name. Signed-off-by:
-
Daniel Stuart authored
Every single baytrail chromebook sets PMC to 0, as can be seeing below by searching through coreboot source code: $ grep -rl "PMC_PLT_CLK\[0\]" . ./rambi/variants/glimmer/devicetree.cb ./rambi/variants/clapper/devicetree.cb ./rambi/variants/swanky/devicetree.cb ./rambi/variants/enguarde/devicetree.cb ./rambi/variants/winky/devicetree.cb ./rambi/variants/kip/devicetree.cb ./rambi/variants/squawks/devicetree.cb ./rambi/variants/orco/devicetree.cb ./rambi/variants/ninja/devicetree.cb ./rambi/variants/heli/devicetree.cb ./rambi/variants/sumo/devicetree.cb ./rambi/variants/banjo/devicetree.cb ./rambi/variants/candy/devicetree.cb ./rambi/variants/gnawty/devicetree.cb ./rambi/variants/rambi/devicetree.cb ./rambi/variants/quawks/devicetree.cb Plus, Cyan (only non-baytrail chromebook with max98090) also needs this patch for audio to work. Thus, this commit adds all the missing devices to bsw_max98090 quirk table, implemented by commit a182ecd3 ("ASoC: intel: cht_bsw_max98090_ti: Add quirk for boards using pmc_plt_clk_0"). Signed-off-by:
-
Jerome Brunet authored
The tohdmitx glue uses regmap MMIO so it should require it. Fixes: c8609f38 ("ASoC: meson: add g12a tohdmitx control") Signed-off-by:
Jerome Brunet <jbrunet@baylibre.com> Link: https://lore.kernel.org/r/20190820123510.22491-1-jbrunet@baylibre.comSigned-off-by:
-
Jerome Brunet authored
Use the devm variant to get the formatter reset so it is properly freed on device removal Fixes: 751bd5db ("ASoC: meson: axg-tdm-formatter: add reset") Signed-off-by:
-
Kunihiko Hayashi authored
When transitioning to supend state, uniphier_aio_dai_suspend() is called and asserts reset lines and disables clocks. However, if there are two or more DAIs, uniphier_aio_dai_suspend() are called multiple times, and double reset assersion will cause. This patch defines the counter that has the number of DAIs at first, and whenever uniphier_aio_dai_suspend() are called, it decrements the counter. And only if the counter is zero, it asserts reset lines and disables clocks. In the same way, uniphier_aio_dai_resume() are called, it increments the counter after deasserting reset lines and enabling clocks. Fixes: 139a3420 ("ASoC: uniphier: add support for UniPhier AIO CPU DAI driver") Signed-off-by:
Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Link: https://lore.kernel.org/r/1566281764-14059-1-git-send-email-hayashi.kunihiko@socionext.comSigned-off-by:
-
- 16 Aug, 2019 5 commits
-
-
Pierre-Louis Bossart authored
Even if ALH has no specific configuration, we still need to handle the common parameters for all DAIs Signed-off-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20190815192018.30570-5-pierre-louis.bossart@linux.intel.comSigned-off-by:
-
Pierre-Louis Bossart authored
The Audio Link Hub DAI does not require any static configuration from topology for now. We still need to pass the frame rate and format to firmware. Signed-off-by:
-
Bard liao authored
Rename SOUNDWIRE to ALH. Signed-off-by:
Bard liao <yung-chuan.liao@linux.intel.com> Signed-off-by:
-
Daniel Baluta authored
Add dummy support for SAI/ESAI digital audio interface IPs found on i.MX8 boards. Signed-off-by:
Daniel Baluta <daniel.baluta@nxp.com> Signed-off-by:
-
Shengjiu Wang authored
For i.MX6 SoloX, there is a mode of the SoC to shutdown all power source of modules during system suspend and resume procedure. Thus, AUDMUX needs to save all the values of registers before the system suspend and restore them after the system resume. Signed-off-by:
Shengjiu Wang <shengjiu.wang@nxp.com> Link: https://lore.kernel.org/r/1565931794-7218-1-git-send-email-shengjiu.wang@nxp.comSigned-off-by:
-
- 15 Aug, 2019 20 commits
-
-
Pan Xiuli authored
Add Kconfig, PCI ID and chip info for EHL platform. Note that the core mask is different from previous platforms, only Core0 can be controlled by the host. Additional patches will be required for multi-core functionality. Signed-off-by:
Pan Xiuli <xiuli.pan@linux.intel.com> Signed-off-by:
-
Pan Xiuli authored
There are no upstream machine drivers just yet so just add dummy table for compilation in nocodec-mode. Signed-off-by:
-
Pan Xiuli authored
Add Kconfig, PCI ID and chip info for Tiger Lake platform. Note that the core mask is different from previous platforms, only Core0 can be controlled by the host. Additional patches will be required for multi-core functionality. Signed-off-by:
-
Pan Xiuli authored
Initial support for TGL w/ RT1308 Signed-off-by:
-
Pierre-Louis Bossart authored
The only configuration parameter is the ALH stream ID. No range checking is done by the driver, the firmware should check that the stream is valid for a specific hardware. Bump the ABI Minor number to keep the alignment with SOF firmware Signed-off-by:
-
Mac Chiang authored
reuse and add Cometlake support with: SSP0 for DA7219 headphone codec SSP1 for MAX98357a speaker amp codec Signed-off-by:
Mac Chiang <mac.chiang@intel.com> Acked-by:
-
Peter Ujfalusi authored
The pcm_mutex is used to prevent concurrent execution of snd_pcm_ops callbacks. This works fine most of the cases but it can not handle setups when the same DAI is used by different rtd, for example: pcm3168a have two DAIs: one for Playback and one for Capture. If the codec is connected to a single CPU DAI we need to have two dai_link to support both playback and capture. In this case the snd_pcm_ops callbacks can be executed in parallel causing unexpected races in DAI drivers. By moving the pcm_mutex up to card level this can be solved while - hopefully - not breaking other setups. Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by:
-
YueHaibing authored
sound/soc/codecs/88pm860x-codec.c:533:38: warning: pcm_switch_controls defined but not used [-Wunused-const-variable=] sound/soc/codecs/88pm860x-codec.c:560:38: warning: aif1_mux defined but not used [-Wunused-const-variable=] They are never used, so can be removed. Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Link: https://lore.kernel.org/r/20190815092547.29564-1-yuehaibing@huawei.comSigned-off-by:
-
YueHaibing authored
sound/soc/codecs/cs42l56.c:206:30: warning: adc_swap_enum defined but not used [-Wunused-const-variable=] It is never used, so can be removed. Reported-by:
-
YueHaibing authored
It seems 'es8328_rline_enum' should be used in es8328_right_line_controls Fixes: 567e4f98 ("ASoC: add es8328 codec driver") Signed-off-by:
-
YueHaibing authored
sound/soc/codecs/es8328.c:102:35: warning: pga_tlv defined but not used [-Wunused-const-variable=] They are never used, so can be removed. Reported-by:
-
YueHaibing authored
sound/soc/codecs/tlv320aic31xx.c:261:29: warning: cm_m_enum defined but not used [-Wunused-const-variable=] It is never used, so can be removed. Reported-by:
-
YueHaibing authored
sound/soc/codecs/tlv320aic23.c:70:29: warning: tlv320aic23_rec_src defined but not used [-Wunused-const-variable=] It is never used, so can be removed. Reported-by:
-
YueHaibing authored
sound/soc/codecs/rt1011.c:981:35: warning: dac_vol_tlv defined but not used [-Wunused-const-variable=] sound/soc/codecs/rt1011.c:982:35: warning: adc_vol_tlv defined but not used [-Wunused-const-variable=] They are never used, so can be removed. Signed-off-by:
-
YueHaibing authored
sound/soc/codecs/max98371.c:157:35: warning: max98371_noload_gain_tlv defined but not used [-Wunused-const-variable=] It is never used, so can be removed. Reported-by:
-
YueHaibing authored
sound/soc/codecs/cs4349.c:358:32: warning: cs4349_runtime_pm defined but not used [-Wunused-const-variable=] cs4349_runtime_pm ops already defined, it seems we should enable it. Reported-by:
-
YueHaibing authored
sound/soc/codecs/cs42l73.c:276:38: warning: vsp_output_mux defined but not used [-Wunused-const-variable=] sound/soc/codecs/cs42l73.c:279:38: warning: xsp_output_mux defined but not used [-Wunused-const-variable=] They are never used, so can be removed. Reported-by:
-
Andy Shevchenko authored
Instead of using two additional "%s" specifiers, put the constant string literals directly to the format specifier. Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Vinod Koul <vkoul@kernel.org> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20190621113116.47525-1-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Jiaxin Yu authored
Most dmics produce a high level when they receive clock. The difference between power-on and memory record time is about 10ms, but the dmic needs 50ms to output normal data. This commit add 100ms delay after SoC output clock so that we can cut off the pop noise at the beginning. Signed-off-by:
Jiaxin Yu <jiaxin.yu@mediatek.com> Link: https://lore.kernel.org/r/1564980997-11359-1-git-send-email-jiaxin.yu@mediatek.comSigned-off-by:
-
YueHaibing authored
sound/soc/mediatek/mt8183/mt8183-mt6358-ts3a227-max98357.c:50:1: warning: mt8183_mt6358_ts3a227_max98357_dapm_widgets defined but not used [-Wunused-const-variable=] sound/soc/mediatek/mt8183/mt8183-mt6358-ts3a227-max98357.c:55:1: warning: mt8183_mt6358_ts3a227_max98357_dapm_routes defined but not used [-Wunused-const-variable=] They are never used, so can be removed. Reported-by:
-
