Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/atheros/atlx/atl1.c: In function 'atl1_set_link_ksettings':
drivers/net/ethernet/atheros/atlx/atl1.c:3280:6: warning:
 variable 'advertising' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/intel/e1000/e1000_main.c: In function 'e1000_watchdog':
drivers/net/ethernet/intel/e1000/e1000_main.c:2436:9: warning:
 variable 'txb2b' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The local variable 'index_specified' is never used after being assigned.
hence it should be redundant adn can be removed.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NFP supports fairly enormous ring sizes (up to 256k descriptors).
In commit 46627170 ("nfp: use kvcalloc() to allocate SW buffer
descriptor arrays") we have started using kvcalloc() functions to
make sure the allocation of software state arrays doesn't hit
the MAX_ORDER limit.  Unfortunately, we can't use virtual mappings
for the DMA region holding HW descriptors.  In case this allocation
fails instead of the generic (and fairly scary) warning/splat in
the logs print a helpful message explaining what happened and
suggesting how to fix it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting register 0x82 to value 01 is done a few lines before for all
chip versions <= 06 anyway. And setting PHY register 0x0b to value 00
is done at the end of rtl8169s_hw_phy_config() already. So we can
remove this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PCI_LATENCY_TIMER is ignored on PCIe, therefore we have to do this
for the PCI chips (version <= 06) only. Also we can move setting
PCI_CACHE_LINE_SIZE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

That local variable are never used after being assigned.
hence it should be redundant and can be removed.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The local variable 'k' is never used after being assigned.
hence it should be redundant adn can be removed.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no way currently for an IPv6 client connect using a loopback
address in a VRF, whereas for IPv4 the loopback address can be added:

    $ sudo ip addr add dev vrfred 127.0.0.1/8
    $ sudo ip -6 addr add ::1/128 dev vrfred
    RTNETLINK answers: Cannot assign requested address

So allow ::1 to be configured on an L3 master device. In order for
this to be usable ip_route_output_flags needs to not consider ::1 to
be a link scope address (since oif == l3mdev and so it would be
dropped), and ipv6_rcv needs to consider the l3mdev to be a loopback
device so that it doesn't drop the packets.
Signed-off-by: Robert Shearman <rshearma@vyatta.att-mail.com>
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Salil Mehta says:

====================
Fixes, cleanups & minor additions to HNS3 driver

This patch-set present some fixes, cleanups to the HNS3 PF and VF driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

So far all the places calling hclge_tm_q_to_qs_map_cfg() are assigning
an u16 type value to "q_id", and in the processing of
hclge_tm_q_to_qs_map_cfg(), it also converts the "q_id" to le16.

The max tqp number for pf can be more than 256, we should use "u16" to
store the queue id, instead of "u8", which may cause data lost.

Fixes: 84844054 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When roce is loaded before nic, the roce client will not be initialized
until nic client is initialized, but roce init flag is set before it.
Furthermore, in this case of nic initialized success and roce failed,
the nic init flag is not set, and roce init flag is not cleared.

This patch fixes it by set init flag only after the client is initialized
successfully.

Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If initialize client failed or finish uninitializing client, we should
clear the client pointer. It may cause unexpected result when use
uninitialized client. Meanwhile, we also should check whether client
exist when uninitialize it.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to hardware's description, the head pointer register should
be written before the tail pointer register while initializing the vf
command queue. Otherwise, it may trigger an interrupt even though there
is no command received.

Fixes: fedd0c15 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function of genphy_read_status is that reading phy information
from HW and using these information to update SW variable. If user
is using ethtool to setting the speed of phy and service task is calling
by hclge_get_mac_phy_link, the result of speed setting is uncertain.
Because ethtool cmd will modified phydev and hclge_get_mac_phy_link also
will modified phydev.

Because phy state machine will update phy link periodically, we can
just use phydev->link to check the link status. This patch removes
function call of genphy_read_status. To ensure accuracy, this patch
adds a phy state check. If phy state is not PHY_RUNNING, we consider
link is down. Because in some scenarios, phydev->link may be link up,
but phy state is not PHY_RUNNING. This is just an intermediate state.
In fact, the link is not ready yet.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

By default, HW link status is up. If hclge_update_link_status is called
before net up, driver will print "link up". It is not suitable. hdev
state check is needed when getting link status.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We clear STATE_DOWN bit of hdev state when starting net, but do not set
it again when stopping net. It causes that the net is down, but hdev state
is still up. STATE_DOWN bit of hdev state should be set when stopping net.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the .ndo_do_ioctl net_device_ops operation to support
the PHY MII ioctl for PF driver.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All pf have permission to read packet statistics of public in hardware,
but the read operation will clear registers which cause statistical
inaccuracy.

This patch removes all packet statistics of public.
Signed-off-by: Junxin Chen <chenjunxin1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The the actual Tx work is minimal, driver can clean up as more
Tx descriptors as possible in a irq.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds unlikely for buf_num check.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All irq will float to cpu0 if do not set irq affinity.
This patch adds default irq affinity in hns3 driver, users can
also change the irq affinity in OS.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
net: phy: phylink: ensure the carrier is off when starting phylink

Following the discussion we had regarding the phylink issue related to
the carrier link state not being off when starting phylink, I sent a fix
patch a few days ago for the PPv2 driver:
https://lkml.org/lkml/2018/9/14/633

The idea was to send a patch which could go to the stable branches, but
a better solution would be to directly call netif_carrier_off() from
within phylink_start(). This is the aim of this series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes the explicit call to netif_carrier_off() in
mvneta_open() as this is already handled in phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes the explicit call to netif_carrier_off() in PPv2's
open() path, as this is now handled in phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phylink made an assumption about the carrier state being down when
calling phylink_start(). If this assumption isn't satisfied, the
internal phylink state could misbehave and a net device could end up not
being functional.

This patch fixes this by explicitly calling netif_carrier_off() in
phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
net: mvpp2: improve the interrupt usage

This series aims to improve the interrupts descriptions and usage in the
Marvell PPv2 driver.

- Before the series interrupts were named after their s/w usage,
  which in fact can be configured. The series rename all those
  interrupts and add a description of the ones left over.

- In PPv2 the interrupts are mapped to vectors. Those vectors were
  directly mapped to a given CPU, and per-cpu accesses were done. While
  this worked on our cases, the registers accesses mapped to the vectors
  are not actually linked to a given CPU. They instead are linked to
  what is called a "s/w thread". The series modify this so that the s/w
  threads are used instead of the CPU numbers, by adding an indirection.
  This means we now can have systems with more CPUs than s/w threads.

This is based on today's net-next, and was tested on various boards
using both versions of the PPv2 engine.

Two more patches will be coming, to update the device trees describing a
PPv2 engine. The patches are ready, but will go through a different
tree. I'll send them once this series will be accepted. This is not an
issue as the PPv2 driver keeps the dt bindings backward compatibility.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

As the mvpp2_percpu_read/write/... functions aren't really per-cpu but
per s/w thread, rename them to include 'thread' instead of 'percpu'.
This is a cosmetic patch.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Marvell PPv2 network controller has 9 internal threads. The driver
works fine when there are less CPUs available than threads. This isn't
true if more CPUs are available. As this is a valid use case, handle
this particular case.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch maps all uses of the CPU to threads. All this_cpu calls are
replaced, and all smp_processor_id() calls are wrapped into the
indirection.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch reworks the Marvell PPv2 driver to stop using directly the
CPU number to access per-thread registers.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the Marvell PPv2 driver the mvpp2_read_relaxed function is only used
in a single file. Make it static and remove its prototype from the
header.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Marvell PPv2 driver has per-cpu functions. As they only are used in
the main file, make them static and remove their prototype from the
header.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Updates the PPv2 driver so that all CPU variables are unsigned, as it
makes no sense to have a negative CPU number. This patch is cosmetic.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>