This patch add provision to show TDLS peer table in debugfs file.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When the driver gets beacon info containing a country IE from user-space
upon .start_ap() callback, it will enable regulatory 802.11d support.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Use cfg80211 change_station to signal the completion of 802.1x
to firmware. This allows FW to take appropriate actions.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When user-space uses a valid ISO-3166-1 country code for its
regulatory domain selection, the driver will try to configure
the firmware to use the same.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When there is no room in the ring for rxbufpost an error is logged,
however this happens quite frequently and can be considered normal
and is certainly recoverable. This patch changes the erorr into
a normal msgbuf log.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When a device is configured for AP mode and it is configured for
WEP then the keys are plumbed first, followed by AP configuration.
During configuration a down command is given to the firmware which
will clear the configured keys. This patch reprograms the WEP keys
after AP has been brought up.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The source file chip.c contained some duplicate defines and
some unused ones. Removing them.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The physical addresses being used by pcie and msgbuf were using
a cast to long, which incorrectly caused it to limit the address
to 32bit. Now explicit u64 is used where needed.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2014-12-30' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

* more work on d0i3 power state
* enhancements to the firmware debugging infrastructure
* support for 2 concurrent channel contexts
* fixes / cleanups in the rate control
* general cleanups

Richard Cochran says:

====================
Fixing the "Time Counter fixes and improvements"

For this series I had only tested the build with ARCH=x86 and arm, but
others like sparc64, microblaze, powerpc, and s390 will fail because
they somehow don't indirectly include clocksource.h for the drivers in
question.

This series fixes the build issues reported by:
 kbuild test robot <fengguang.wu@intel.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The timecounter/cyclecounter code has moved, so users need the new include.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver uses the function, clocksource_khz2mult, and so it really must
include clocksource.h.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need for users of the timecounter/cyclecounter code to include
clocksource.h just for a single macro.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

OVS development is moved to netdev mailing list. Update tree and
list in MAINTAINERS file.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2015-01-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Changes:

* ath9k: enable Transmit Power Control (TPC) for ar9003 chips

* rtlwifi: cleanup and updates from the vendor driver

* rsi: fix memory leak related to firmware image

* ath: parameter fix for FCC DFS pattern
Signed-off-by: David S. Miller <davem@davemloft.net>

Removes some functions that are not used anywhere:
enic_dev_enable2_done() enic_dev_enable2() enic_dev_deinit_done()
enic_dev_init_prov2() enic_vnic_dev_deinit()

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removes some functions that are not used anywhere:
Read_hfc32() Write_hfc32() Write_hfc16()

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the function smt_ifconfig() that is not used anywhere.

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removes some functions that are not used anywhere:
dbgi_rd_rsp3() dbgi_wr_addr3()

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not needed, only four cases:
 - kfree_skb (or one of its aliases).
   Don't need to zero, memory will be freed.
 - kfree_skb_partial and head was stolen:  memory will be freed.
 - skb_morph:  The skb header fields (including tc ones) will be
   copied over from the 'to-be-morphed' skb right after
   skb_release_head_state returns.
 - skb_segment:  Same as before, all the skb header
   fields are copied over from the original skb right away.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg say:

====================
pull request: bluetooth-next 2014-12-31

Here's the first batch of bluetooth patches for 3.20.

 - Cleanups & fixes to ieee802154  drivers
 - Fix synchronization of mgmt commands with respective HCI commands
 - Add self-tests for LE pairing crypto functionality
 - Remove 'BlueFritz!' specific handling from core using a new quirk flag
 - Public address configuration support for ath3012
 - Refactor debugfs support into a dedicated file
 - Initial support for LE Data Length Extension feature from Bluetooth 4.2

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This results in an approximately 30% increase in throughput
when handling encapsulated bulk traffic.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the only tunnel protocol that supports GRO with encapsulated
Ethernet is VXLAN. This pulls out the Ethernet code into a proper layer
so that it can be used by other tunnel protocols such as GRE and Geneve.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to set the clock speed in read/write which will be performed
unnecessarily for each mdio access. Init it during probe is enough.

Also, the hardcoded clock value is not a proper way for all SoCs.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Which is wrong and not used, so no extra space needed by
mdiobus_alloc_size(), use mdiobus_alloc() instead.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the reset is just clock setting, individual mdio reset is
not available.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Roger Chen says:

====================
support GMAC driver for RK3288

Roger Chen (6):
  patch1: add driver for Rockchip RK3288 SoCs integrated GMAC
  patch2: define clock ID used for GMAC
  patch3: modify CRU config for Rockchip RK3288 SoCs integrated GMAC
  patch4: dts: rockchip: add gmac info for rk3288
  patch5: dts: rockchip: enable gmac on RK3288 evb board
  patch6: add document for Rockchip RK3288 GMAC

Tested on rk3288 evb board:
Execute the following command to enable ethernet,
set local IP and ping a remote host.

busybox ifconfig eth0 up
busybox ifconfig eth0 192.168.1.111
ping 192.168.1.1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The document descripts how to add properties for GMAC in device tree.

change since v2:

1. remove power-gpio, reset-gpio, phyirq-gpio, pmu_regulator setting
2. add "snps,reset-gpio", "snps,reset-active-low;" "snps,reset-delays-us"
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enable gmac in rk3288-evb-rk808.dts

changes since v2:
1. add fixed regulator for PHY
2. remove power-gpio, reset-gpio, phyirq-gpio, pmu_regulator setting
3. add "snps,reset-gpio", "snps,reset-active-low;" "snps,reset-delays-us"
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

add gmac info in rk3288.dtsi for GMAC driver

changes since v2:
1. add drive-strength in the pinctrl settings
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

modify CRU config for GMAC driver

changes since v2:
1. remove SCLK_MAC_PLL
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

changes since v2:
1. remove SCLK_MAC_PLL
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver is based on stmmac driver.

changes since v2:
- use tab instead of space for macros
- use HIWORD_UPDATE macro for GMAC_CLK_RX_DL_CFG and GMAC_CLK_TX_DL_CFG
- remove drive-strength setting in the driver and set it in the pinctrl settings
- use dev_err instead of pr_err
- remove clock names's macros, just use the real name of the clock
- use devm_clk_get() instead of clk_get()
- remove clk_set_parent(bsp_priv->clk_mac, bsp_priv->clk_mac_pll)
- remove gpio setting for LDO, just use regulator API
- remove phy reset using gpio in the glue layer, it has been handled in the stmmac driver
- remove handling phy interrupt (mii interrupt)

changes since v1:
- use BIT() to set register
- combine two remap_write() operations into one for the same register
- use macros for register value setting
- remove grf fail check in rk_gmac_setup() and save all the check in set_rgmii_speed()
- remove .tx_coe=1 in rk_gmac_data
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>