- 06 Jun, 2017 8 commits
-
-
Ville Syrjälä authored
The clipped src coordinates have already been rotated by 270 degrees for when the plane rotation is 90/270 degrees, hence the FBC code should no longer swap the width and height. Cc: stable@vger.kernel.org Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Fixes: b63a16f6 ("drm/i915: Compute display surface offset in the plane check hook for SKL+") Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170331180056.14086-4-ville.syrjala@linux.intel.comReviewed-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Tested-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
-
Ville Syrjälä authored
skl_check_plane_surface() already rotates the clipped plane source coordinates to match the scanout direction because that's the way the GTT mapping is set up. Thus we no longer need to rotate the coordinates in the watermark code. For cursors we use the non-clipped coordinates which are not rotated appropriately, but that doesn't actually matter since cursors don't even support 90/270 degree rotation. v2: Resolve conflicts from SKL+ wm rework Cc: stable@vger.kernel.org Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Fixes: b63a16f6 ("drm/i915: Compute display surface offset in the plane check hook for SKL+") Signed-off-by:
-
Ville Syrjälä authored
Starting from commit b63a16f6 ("drm/i915: Compute display surface offset in the plane check hook for SKL+") we've already rotated the src coordinates by 270 degrees by the time we check if a scaler is needed or not, so we must not account for the rotation a second time. Previously we did these steps in the opposite order and hence the scaler check had to deal with rotation itself. The double rotation handling causes us to enable a scaler pretty much every time 90/270 degree plane rotation is requested, leading to fuzzier fonts and whatnot. v2: s/unsigned/unsigned int/ to appease checkpatch v3: s/DRM_ROTATE_0/DRM_MODE_ROTATE_0/ Cc: stable@vger.kernel.org Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reported-by:
-
Ville Syrjälä authored
Restore the lost has_fbc flag for mobile ILK. Cc: Carlos Santa <carlos.santa@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Fixes: a1323380 ("drm/i915: Introduce GEN5_FEATURES for device info") Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com>
-
Ville Syrjälä authored
We're not that short on characters that we can't spell out "false_color". Saves me from figuring out what "fc" means the next time look at the code. Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
-
Ville Syrjälä authored
The number of compressed segments has been available ever since FBC2 was introduced in g4x, it just moved from the STATUS register into STATUS2 on IVB. For FBC1 if we really wanted the number of compressed segments we'd have to trawl through the tags, but in this case since the code just uses the number of compressed segments as an indicator whether compression has occurred we can just check the state of the COMPRESSING and COMPRESSED bits. IIRC the hardware will try to periodically recompress all uncompressed lines even if they haven't changed and the COMPRESSED bit will be cleared while the compressor is running, so just checking the COMPRESSED bit might not give us the right answer. Hence it seems better to check for both COMPRESSED and COMPRESSING as that should tell us that the compressor is at least trying to do something. While at it move the IVB+ register define to the right place, unify the naming convention of the compressed segment count masks, and fix up the mask for g4x. v2: s/ILK_DPFC_STATUS2/IVB_FBC_STATUS2/ (Paulo) Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk> Signed-off-by:
-
Ville Syrjälä authored
The scanline counter is bonkers on VLV/CHV DSI. The scanline counter increment is not lined up with the start of vblank like it is on every other platform and output type. This causes problems for both the vblank timestamping and atomic update vblank evasion. On my FFRD8 machine at least, the scanline counter increment happens about 1/3 of a scanline ahead of the start of vblank (which is where all register latching happens still). That means we can't trust the scanline counter to tell us whether we're in vblank or not while we're on that particular line. In order to keep vblank timestamping in working condition when called from the vblank irq, we'll leave scanline_offset at one, which means that the entire line containing the start of vblank is considered to be inside the vblank. For the vblank evasion we'll need to consider that entire line to be bad, since we can't tell whether the registers already got latched or not. And we can't actually use the start of vblank interrupt to get us past that line as the interrupt would fire too soon, and then we'd up waiting for the next start of vblank instead. One way around that would using the frame start interrupt instead since that wouldn't fire until the next scanline, but that would require some bigger changes in the interrupt code. So for simplicity we'll just poll until we get past the bad line. v2: Adjust the comments a bit Cc: stable@vger.kernel.org Cc: Jonas Aaberg <cja@gmx.net> Tested-by:
Jonas Aaberg <cja@gmx.net> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99086Signed-off-by:
Mika Kahola <mika.kahola@intel.com> Reviewed-by:
-
Ville Syrjälä authored
Remove the SNB PCH refclock init call from the runtime resume handler. I don't think it was actually needed even when we had SNB runtime PM, and if definitely isn't needed ever since SNB runtime PM was nuked in commit d4c5636e ("drm/i915: Remove runtime PM for SNB"). Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by:
-
- 02 Jun, 2017 8 commits
-
-
Rodrigo Vivi authored
Panel Power sequences for CNP is similar to Broxton, but with only one sequencer. Main difference from SPT is that PP_DIVISOR was removed and power cycle delay has been moved to PP_CONTROL. v2: Add missed pp_div write, that is now part of PP_CONTROL[8:4] as on Broxton. (Found by DK) v3: Improve commit message. (By DK) Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by:Clinton Taylor <clinton.a.taylor@intel.com> Reviewed-by:
Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-6-git-send-email-rodrigo.vivi@intel.com
-
Rodrigo Vivi authored
On CNP PCH based platforms the gmbus is on the south display that is on PCH. The existing implementation for previous platforms already covers the need for CNP expect for the pin pair configuration that follows similar definitions that we had on BXT. v2: Don't drop "_BXT" as the indicator of the first platform supporting this pin numbers. Suggested by Daniel. v3: Add missing else and fix register table since CNP GPIO_CTL starts on 0xC5014. v4: Fix pin number and map according to the current available VBT. Re-add pin 4 for port D. Lost during some rebase. v5: Use table as spec. If VBT is wrong it should be ignored. Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by:Anusha Srivatsa <anusha.srivatsa@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-5-git-send-email-rodrigo.vivi@intel.com
-
Rodrigo Vivi authored
Split out BXT and CNP's setup_backlight(),enable_backlight(), disable_backlight() and hz_to_pwm() into two separate functions instead of reusing BXT function. Reuse set_backlight() and get_backlight() since they have no reference to the utility pin. v2: Reuse BXT functions with controller 0 instead of redefining it. (Jani). Use dev_priv->rawclk_freq instead of getting the value from SFUSE_STRAP. v3: Avoid setup backligh controller along with hooks and fully reuse hooks setup as suggested by Jani. v4: Clean up commit message. v5: Implement per PCH instead per platform. v6: Introduce a new function for CNP.(Jani and Ville) v7: Squash the all CNP Backlight support patches into a single patch. (Jani) v8: Correct indentation, remove unneeded blank lines and correct mail address (Jani). v9: Remove unused enum pipe. (by CI) v10: Remove comment mentioning SFUSE_STRAP in a part of the code that we don't use it. (Jani) Make controller = 0 since current CNP has only one controller and put a comment mentioning why we reuse the BXT definitions and are keeping the controller = 0. (DK) v11: Remove spurious line. (DK) Reviewed-by:Jani Nikula <jani.nikula@intel.com> Suggested-by:
Ville Syrjala <ville.syrjala@intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Rodrigo Vivi authored
RAWCLK_FREQ register has changed for platforms with CNP+. [29:26] This field provides the denominator for the fractional part of the microsecond counter divider. The numerator is fixed at 1. Program this field to the denominator of the fractional portion of reference frequency minus one. If the fraction is 0, program to 0. 0100b = Fraction .2 MHz = Fraction 1/5. 0000b = Fraction .0 MHz. [25:16] This field provides the integer part of the microsecond counter divider. Program this field to the integer portion of the reference frequenct minus one. Also this register tells us that proper raw clock should be read from SFUSE_STRAP and programmed to this register. Up to this point on other platforms we are reading instead of programming it so probably relying on whatever BIOS had configured here. Now on let's follow the spec and also program this register fetching the right value from SFUSE_STRAP as Spec tells us to do. v2: Read from SFUSE_STRAP and Program RAWCLK_FREQ instead of reading the value relying someone else will program that for us. v3: Add missing else. (Jani) v4: Addressing all Ville's catches: Use macro for shift bits instead of defining shift. Remove shift from the cleaning bits with mask that already has it. Add missing I915_WRITE to actually write the reg. Stop using useless DIV_ROUND_* on divider that is exact dividion and use DIV_ROUND_CLOSEST for the fraction part. v5: Remove useless Read-Modify-Write on raclk_freq reg. (Ville). v6: Change is per PCH instead of per platform. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by: -
Dhinakaran Pandiyan authored
The first two bytes of PCI ID for CNP_LP PCH are the same as that of SPT_LP. We should really be looking at the first 9 bits instead of the first 8 to identify platforms, although this seems to have not caused any problems on earlier platforms. Introduce a 9 bit extended mask for SPT and CNP while not touching the code for any of the other platforms. v2: (Rodrigo) Make platform agnostic and fix commit message. Signed-off-by:
-
Rodrigo Vivi authored
Most of south engine display that is in PCH is still the same as SPT and KBP, except for this key differences: - Backlight: Backlight programming changed in CNP PCH. - Panel Power: Sligh programming changed in CNP PCH. - GMBUS and GPIO: The pin mapping has changed in CNP PCH. All of these changes follow more the BXT style. v2: Update definition to use dev_priv isntead of dev (Tvrtko). Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Signed-off-by:
-
Chris Wilson authored
In commit 5763ff04 ("drm/i915: Avoid GPU stalls from kswapd") we stopped direct reclaim and kswapd from triggering GPU/client stalls whilst running (by restricting the objects they could reap to be idle). However with abusive GPU usage, it becomes quite easy to starve kswapd of memory and prevent it from making forward progress towards obtaining enough free memory (thus driving the system closer to swap exhaustion). Relax the previous restriction to allow kswapd (but not direct reclaim) to stall the device whilst reaping purgeable pages. v2: Also acquire the rpm wakelock to allow kswapd to unbind buffers. Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170601133331.5973-1-chris@chris-wilson.co.ukReviewed-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by:
Mika Kuoppala <mika.kuoppala@intel.com>
-
Weinan Li authored
I915_GEM_GET_APERTURE ioctl is used to probe aperture size from userspace. In gvt environment, each vm only use the ballooned part of aperture, so we should return the correct available aperture size exclude the reserved part by balloon. v2: add 'reserved' in struct i915_address_space to record the reserved size in ggtt (Chris) v3: remain aper_size as total, adjust aper_available_size exclude reserved and pinned. UMD driver need to adjust the max allocation size according to the available aperture size but not total size. KMD return the correct usable aperture size any time (Chris, Joonas) v4: decrease reserved in deballoon (Joonas) v5: add onion teardown in balloon, add vgt_deballoon_space (Joonas) v6: change title name (Zhenyu) v7: code style refine (Joonas) Suggested-by:
Weinan Li <weinan.z.li@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1496198152-14175-1-git-send-email-weinan.z.li@intel.comReviewed-by:
-
- 01 Jun, 2017 10 commits
-
-
Chris Wilson authored
The assertion that we want to make before disabling the pin of the pages for the unknown swizzling quirk is that the quirk is indeed active, and that the quirk is disabled before we do apply it to the pages. Fixes: 2c3a3f44 ("drm/i915: Fix pages pin counting around swizzle quirk") Fixes: 957870f9 ("drm/i915: Split out i915_gem_object_set_tiling()") Signed-off-by:
-
Chris Wilson authored
As another precaution when testing whether the CS engine is actually idle, also inspect the ring's HEAD/TAIL registers, which should be equal when there are no commands left to execute by the GPU. Signed-off-by:
-
Chris Wilson authored
When we enable the GuC, we enable an alternative mechanism for doing post-GGTT update invalidation. Likewise, when we disable the GuC, we restore the previous method. Assert that we change between known endpoints, so that we can catch if we accidentally clobber some other gen and if we change the invalidate routine without updating guc. Signed-off-by:
Michal Wajdeczko <michal.wajdeczko@intel.com> Reviewed-by:
-
Jani Nikula authored
Print DID not VID on the DID error path. Looks like a copy-paste error from the VID error path. Clarify and clean up error logging, making them distinguishable from each other, while at it. Reported-by:
Petru Mihancea <petrum@gmail.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101243Reviewed-by:
-
Imre Deak authored
Atm disabling either DP or eDP outputs can generate a spurious short pulse interrupt. The reason is that after disabling the port the source will stop sending a valid stream data, while the sink expects either a valid stream or the idle pattern. Since neither of this is sent the sink assumes (after an arbitrary delay) that the link is lost and requests for link retraining with a short pulse. The spurious pulse is a real problem at least for eDP panels with long power-off / power-cycle delays: as part of disabling the output we disable the panel power. The subsequent spurious short pulse handling will have to turn the power back on, which means the driver has to do a redundant wait for the power-off and power-cycle delays. During system suspend this leads to an unnecessary delay up to ~1s on systems with such panels as reported by Rui. To fix this put the sink to DPMS D3 state before turning off the port. According to the DP spec in this state the sink should not request retraining. This is also what we do already on pre-ddi platforms. As an alternative I also tried configuring the port to send idle pattern - which is against BSPec - and leave the port in normal mode before turning off the port. Neither of these resolved the problem. Cc: Zhang Rui <rui.zhang@intel.com> Cc: David Weinehall <david.weinehall@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reported-and-tested-by:
Zhang Rui <rui.zhang@intel.com> Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
-
Maarten Lankhorst authored
Seems that GLK has a dotclock that's twice the display clock. skl_max_scale checks for IS_GEMINILAKE, so perform the same check here. While at it, change the DRM_ERROR to DEBUG_KMS. Fixes: 73b0ca8e ("drm/i915/skl+: consider max supported plane pixel rate while scaling") Cc: Mahesh Kumar <mahesh1.kumar@intel.com> Signed-off-by:
Mahesh Kumar <mahesh1.kumar@intel.com>
-
Chris Wilson authored
Commit 7c3f86b6 ("drm/i915: Invalidate the guc ggtt TLB upon insertion") added the restoration of the invalidation routine after the GuC was disabled, but missed that the GuC was unconditionally disabled when not used. This then overwrites the invalidate routine for the older chipsets, causing havoc and breaking resume as the most obvious victim. We place the guard inside i915_ggtt_disable_guc() to be backport friendly (the bug was introduced into v4.11) but it would be preferred to be in more control over when this was guard (i.e. do not try and teardown the data structures before we have enabled them). That should be true with the reorganisation of the guc loaders. Reported-by:
Michel Thierry <michel.thierry@intel.com>
-
Mahesh Kumar authored
A display resolution is only supported if it meets all the restrictions below for Maximum Pipe Pixel Rate. The display resolution must fit within the maximum pixel rate output from the pipe. Make sure that the display pipe is able to feed pixels at a rate required to support the desired resolution. For each enabled plane on the pipe { If plane scaling enabled { Horizontal down scale amount = Maximum[1, plane horizontal size / scaler horizontal window size] Vertical down scale amount = Maximum[1, plane vertical size / scaler vertical window size] Plane down scale amount = Horizontal down scale amount * Vertical down scale amount Plane Ratio = 1 / Plane down scale amount } Else { Plane Ratio = 1 } If plane source pixel format is 64 bits per pixel { Plane Ratio = Plane Ratio * 8/9 } } Pipe Ratio = Minimum Plane Ratio of all enabled planes on the pipe If pipe scaling is enabled { Horizontal down scale amount = Maximum[1, pipe horizontal source size / scaler horizontal window size] Vertical down scale amount = Maximum[1, pipe vertical source size / scaler vertical window size] Note: The progressive fetch - interlace display mode is equivalent to a 2.0 vertical down scale Pipe down scale amount = Horizontal down scale amount * Vertical down scale amount Pipe Ratio = Pipe Ratio / Pipe down scale amount } Pipe maximum pixel rate = CDCLK frequency * Pipe Ratio In this patch our calculation is based on pipe downscale amount (plane max downscale amount * pipe downscale amount) instead of Pipe Ratio. So, max supported crtc clock with given scaling = CDCLK / pipe downscale. Flip will fail if, current crtc clock > max supported crct clock with given scaling. Changes since V1: - separate out fixed_16_16 wrapper API definition Changes since V2: - Fix buggy crtc !active condition (Maarten) - use intel_wm_plane_visible wrapper as per Maarten's suggestion Changes since V3: - Change failure return from ERANGE to EINVAL Changes since V4: - Rebase based on previous patch changes Changes since V5: - return EINVAL instead of continue (Maarten) Changes since V6: - Improve commit message - Address review comment Changes since V7: - use !enable instead of !active - rename config variable for consistency (Maarten) Signed-off-by:Matt Roper <matthew.d.roper@intel.com> Reviewed-by:
-
Kumar, Mahesh authored
This patch implements new DDB allocation algorithm as per HW team recommendation. This algo takecare of scenario where we allocate less DDB for the planes with lower relative pixel rate, but they require more DDB to work. It also takes care of enabling same watermark level for each plane in crtc, for efficient power saving. Changes since v1: - Rebase on top of Paulo's patch series Changes since v2: - Fix the for loop condition to enable WM Changes since v3: - Fix crash in cursor i-g-t reported by Maarten - Rebase after addressing Paulo's comments - Few other ULT fixes Changes since v4: - Rebase on drm-tip - Added separate function to enable WM levels Changes since v5: - Fix a crash identified in skl-6770HQ system Changes since v6: - Address review comments from Matt Changes since v7: - Fix failure return in skl_compute_plane_wm (Matt) - fix typo Changes since v8: - Always check cursor wm enable irrespective of total_data_rate Changes since v9: - fix typo Signed-off-by:
-
Maarten Lankhorst authored
On some systems there can be a race condition in which no crtc state is added to the first atomic commit. This results in all crtc's having a null DDB allocation, causing a FIFO underrun on any update until the first modeset. Changes since v1: - Do not take the connection_mutex, this is already done below. Reported-by:
-
- 31 May, 2017 2 commits
-
-
Imre Deak authored
Since commit bac2a909 Author: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Date: Wed Jan 21 02:17:42 2015 +0100 PCI / PM: Avoid resuming PCI devices during system suspend PCI devices will default to allowing the system suspend complete optimization where devices are not woken up during system suspend if they were already runtime suspended. This however breaks the i915/HDA drivers for two reasons: - The i915 driver has system suspend specific steps that it needs to run, that bring the device to a different state than its runtime suspended state. - The HDA driver's suspend handler requires power that it will request from the i915 driver's power domain handler. This in turn requires the i915 driver to runtime resume itself, but this won't be possible if the suspend complete optimization is in effect: in this case the i915 runtime PM is disabled and trying to get an RPM reference returns -EACCESS. Solve this by requiring the PCI/PM core to resume the device during system suspend which in effect disables the suspend complete optimization. Regardless of the above commit the optimization stayed disabled for DRM devices until commit d14d2a84 Author: Lukas Wunner <lukas@wunner.de> Date: Wed Jun 8 12:49:29 2016 +0200 drm: Remove dev_pm_ops from drm_class so this patch is in practice a fix for this commit. Another reason for the bug staying hidden for so long is that the optimization for a device is disabled if it's disabled for any of its children devices. i915 may have a backlight device as its child which doesn't support runtime PM and so doesn't allow the optimization either. So if this backlight device got registered the bug stayed hidden. Credits to Marta, Tomi and David who enabled pstore logging, that caught one instance of this issue across a suspend/ resume-to-ram and Ville who rememberd that the optimization was enabled for some devices at one point. The first WARN triggered by the problem: [ 6250.746445] WARNING: CPU: 2 PID: 17384 at drivers/gpu/drm/i915/intel_runtime_pm.c:2846 intel_runtime_pm_get+0x6b/0xd0 [i915] [ 6250.746448] pm_runtime_get_sync() failed: -13 [ 6250.746451] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul snd_hda_codec_realtek snd_hda_codec_generic ghash_clmulni_intel e1000e snd_hda_codec snd_hwdep snd_hda_core ptp mei_me pps_core snd_pcm lpc_ich mei prime_ numbers i2c_hid i2c_designware_platform i2c_designware_core [last unloaded: i915] [ 6250.746512] CPU: 2 PID: 17384 Comm: kworker/u8:0 Tainted: G U W 4.11.0-rc5-CI-CI_DRM_334+ #1 [ 6250.746515] Hardware name: /NUC5i5RYB, BIOS RYBDWi35.86A.0362.2017.0118.0940 01/18/2017 [ 6250.746521] Workqueue: events_unbound async_run_entry_fn [ 6250.746525] Call Trace: [ 6250.746530] dump_stack+0x67/0x92 [ 6250.746536] __warn+0xc6/0xe0 [ 6250.746542] ? pci_restore_standard_config+0x40/0x40 [ 6250.746546] warn_slowpath_fmt+0x46/0x50 [ 6250.746553] ? __pm_runtime_resume+0x56/0x80 [ 6250.746584] intel_runtime_pm_get+0x6b/0xd0 [i915] [ 6250.746610] intel_display_power_get+0x1b/0x40 [i915] [ 6250.746646] i915_audio_component_get_power+0x15/0x20 [i915] [ 6250.746654] snd_hdac_display_power+0xc8/0x110 [snd_hda_core] [ 6250.746661] azx_runtime_resume+0x218/0x280 [snd_hda_intel] [ 6250.746667] pci_pm_runtime_resume+0x76/0xa0 [ 6250.746672] __rpm_callback+0xb4/0x1f0 [ 6250.746677] ? pci_restore_standard_config+0x40/0x40 [ 6250.746682] rpm_callback+0x1f/0x80 [ 6250.746686] ? pci_restore_standard_config+0x40/0x40 [ 6250.746690] rpm_resume+0x4ba/0x740 [ 6250.746698] __pm_runtime_resume+0x49/0x80 [ 6250.746703] pci_pm_suspend+0x57/0x140 [ 6250.746709] dpm_run_callback+0x6f/0x330 [ 6250.746713] ? pci_pm_freeze+0xe0/0xe0 [ 6250.746718] __device_suspend+0xf9/0x370 [ 6250.746724] ? dpm_watchdog_set+0x60/0x60 [ 6250.746730] async_suspend+0x1a/0x90 [ 6250.746735] async_run_entry_fn+0x34/0x160 [ 6250.746741] process_one_work+0x1f2/0x6d0 [ 6250.746749] worker_thread+0x49/0x4a0 [ 6250.746755] kthread+0x107/0x140 [ 6250.746759] ? process_one_work+0x6d0/0x6d0 [ 6250.746763] ? kthread_create_on_node+0x40/0x40 [ 6250.746768] ret_from_fork+0x2e/0x40 [ 6250.746778] ---[ end trace 102a62fd2160f5e6 ]--- v2: - Use the new pci_dev->needs_resume flag, to avoid any overhead during the ->pm_prepare hook. (Rafael) v3: - Update commit message to reference the actual regressing commit. (Lukas) v4: - Rebase on v4 of patch 1/2. Fixes: d14d2a84 ("drm: Remove dev_pm_ops from drm_class") References: https://bugs.freedesktop.org/show_bug.cgi?id=100378 References: https://bugs.freedesktop.org/show_bug.cgi?id=100770 Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Marta Lofstedt <marta.lofstedt@intel.com> Cc: David Weinehall <david.weinehall@linux.intel.com> Cc: Tomi Sarvela <tomi.p.sarvela@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Takashi Iwai <tiwai@suse.de> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: linux-pci@vger.kernel.org Cc: <stable@vger.kernel.org> # v4.10.x: 4d071c32 - PCI/PM: Add needs_resume flag Cc: <stable@vger.kernel.org> # v4.10.x Signed-off-by:
Marta Lofstedt <marta.lofstedt@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1493726649-32094-2-git-send-email-imre.deak@intel.com
-
Michel Thierry authored
We are passing parameters in the wrong order to find next zero bit, and when it doesn't find anything it returns size (offset in the code), which is always zero. For reference the function is defined as: find_next_bit( *addr, size, offset ) The incorrect parameter order was added by commit abddffdf ("drm/i915/guc: Sanitize GuC client initialization"). Luckily, currently we only use a single guc client and a single doorbell, which happens to be zero; therefore it isn't necessary to backport this fix (which would be for v4.12). Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Oscar Mateo <oscar.mateo@intel.com> Signed-off-by:
Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by:
-
- 30 May, 2017 12 commits
-
-
Nagaraju, Vathsala authored
psr1 is also disabled for panel resolution greater than 32X20. Added psr2 check to disable only for psr2 panels having resolution greater than 32X20. issue was introduced by commit-id : "acf45d11" commit message: "PSR2 is restricted to work with panel resolutions upto 3200x2000, move the check to intel_psr_match_conditions and fully block psr." v2: (Rodrigo) Add previous commit details which introduced the issue Fixes: acf45d11 ("drm/i915/psr: disable psr2 for resolution greater than 32X20") Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Jim Bride <jim.bride@linux.intel.com> Cc: Yaroslav Shabalin <yaroslav.shabalin@gmail.com> Reported-by:
Yaroslav Shabalin <yaroslav.shabalin@gmail.com> Reviewed-by:
vathsala nagaraju <vathsala.nagaraju@intel.com> Signed-off-by:
-
Chris Wilson authored
Allow intel_engine_is_idle() to be called outside of the GT wakeref by acquiring the device runtime pm for ourselves. This allows the function to act as check after we assume the engine is idle and we release the GT wakeref held whilst we have requests. At the moment, we do not call it outside of an awake context but taking the wakeref as required makes it more convenient to use for quick debugging in future. [ 2613.401647] RPM wakelock ref not held during HW access [ 2613.401684] ------------[ cut here ]------------ [ 2613.401720] WARNING: CPU: 5 PID: 7739 at drivers/gpu/drm/i915/intel_drv.h:1787 gen6_read32+0x21f/0x2b0 [i915] [ 2613.401731] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp snd_hda_codec_realtek coretemp snd_hda_codec_generic crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm r8169 mii mei_me lpc_ich mei prime_numbers [last unloaded: i915] [ 2613.401823] CPU: 5 PID: 7739 Comm: drv_missed_irq Tainted: G U 4.12.0-rc2-CI-CI_DRM_421+ #1 [ 2613.401825] Hardware name: MSI MS-7924/Z97M-G43(MS-7924), BIOS V1.12 02/15/2016 [ 2613.401840] task: ffff880409e3a740 task.stack: ffffc900084dc000 [ 2613.401861] RIP: 0010:gen6_read32+0x21f/0x2b0 [i915] [ 2613.401863] RSP: 0018:ffffc900084dfce8 EFLAGS: 00010292 [ 2613.401869] RAX: 000000000000002a RBX: ffff8804016a8000 RCX: 0000000000000006 [ 2613.401871] RDX: 0000000000000006 RSI: ffffffff81cbf2d9 RDI: ffffffff81c9e3a7 [ 2613.401874] RBP: ffffc900084dfd18 R08: ffff880409e3afc8 R09: 0000000000000000 [ 2613.401877] R10: 000000008a1c483f R11: 0000000000000000 R12: 000000000000209c [ 2613.401879] R13: 0000000000000001 R14: ffff8804016a8000 R15: ffff8804016ac150 [ 2613.401882] FS: 00007f39ef3dd8c0(0000) GS:ffff88041fb40000(0000) knlGS:0000000000000000 [ 2613.401885] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 2613.401887] CR2: 00000000023717c8 CR3: 00000002e7b34000 CR4: 00000000001406e0 [ 2613.401889] Call Trace: [ 2613.401912] intel_engine_is_idle+0x76/0x90 [i915] [ 2613.401931] i915_gem_wait_for_idle+0xe6/0x1e0 [i915] [ 2613.401951] fault_irq_set+0x40/0x90 [i915] [ 2613.401970] i915_ring_test_irq_set+0x42/0x50 [i915] [ 2613.401976] simple_attr_write+0xc7/0xe0 [ 2613.401981] full_proxy_write+0x4f/0x70 [ 2613.401987] __vfs_write+0x23/0x120 [ 2613.401992] ? rcu_read_lock_sched_held+0x75/0x80 [ 2613.401996] ? rcu_sync_lockdep_assert+0x2a/0x50 [ 2613.401999] ? __sb_start_write+0xfa/0x1f0 [ 2613.402004] vfs_write+0xc5/0x1d0 [ 2613.402008] ? trace_hardirqs_on_caller+0xe7/0x1c0 [ 2613.402013] SyS_write+0x44/0xb0 [ 2613.402020] entry_SYSCALL_64_fastpath+0x1c/0xb1 [ 2613.402022] RIP: 0033:0x7f39eded6670 [ 2613.402025] RSP: 002b:00007fffdcdcb1a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 2613.402030] RAX: ffffffffffffffda RBX: ffffffff81470203 RCX: 00007f39eded6670 [ 2613.402033] RDX: 0000000000000001 RSI: 000000000041bc33 RDI: 0000000000000006 [ 2613.402036] RBP: ffffc900084dff88 R08: 00007f39ef3dd8c0 R09: 0000000000000001 [ 2613.402038] R10: 0000000000000000 R11: 0000000000000246 R12: 000000000041bc33 [ 2613.402041] R13: 0000000000000006 R14: 0000000000000000 R15: 0000000000000000 [ 2613.402046] ? __this_cpu_preempt_check+0x13/0x20 [ 2613.402052] Code: 01 9b fa e0 0f ff e9 28 fe ff ff 80 3d 6a dd 0e 00 00 0f 85 29 fe ff ff 48 c7 c7 48 19 29 a0 c6 05 56 dd 0e 00 01 e8 da 9a fa e0 <0f> ff e9 0f fe ff ff b9 01 00 00 00 ba 01 00 00 00 44 89 e6 48 [ 2613.402199] ---[ end trace 31f0cfa93ab632bf ]--- Fixes: 5400367a ("drm/i915: Ensure the engine is idle before manually changing HWS") Signed-off-by:
-
Chris Wilson authored
If the device is asleep (no GT wakeref), we know the GPU is already idle. If we add an early return, we can avoid touching registers and checking hw state outside of the assumed GT wakelock. This prevents causing such errors whilst debugging: [ 2613.401647] RPM wakelock ref not held during HW access [ 2613.401684] ------------[ cut here ]------------ [ 2613.401720] WARNING: CPU: 5 PID: 7739 at drivers/gpu/drm/i915/intel_drv.h:1787 gen6_read32+0x21f/0x2b0 [i915] [ 2613.401731] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp snd_hda_codec_realtek coretemp snd_hda_codec_generic crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm r8169 mii mei_me lpc_ich mei prime_numbers [last unloaded: i915] [ 2613.401823] CPU: 5 PID: 7739 Comm: drv_missed_irq Tainted: G U 4.12.0-rc2-CI-CI_DRM_421+ #1 [ 2613.401825] Hardware name: MSI MS-7924/Z97M-G43(MS-7924), BIOS V1.12 02/15/2016 [ 2613.401840] task: ffff880409e3a740 task.stack: ffffc900084dc000 [ 2613.401861] RIP: 0010:gen6_read32+0x21f/0x2b0 [i915] [ 2613.401863] RSP: 0018:ffffc900084dfce8 EFLAGS: 00010292 [ 2613.401869] RAX: 000000000000002a RBX: ffff8804016a8000 RCX: 0000000000000006 [ 2613.401871] RDX: 0000000000000006 RSI: ffffffff81cbf2d9 RDI: ffffffff81c9e3a7 [ 2613.401874] RBP: ffffc900084dfd18 R08: ffff880409e3afc8 R09: 0000000000000000 [ 2613.401877] R10: 000000008a1c483f R11: 0000000000000000 R12: 000000000000209c [ 2613.401879] R13: 0000000000000001 R14: ffff8804016a8000 R15: ffff8804016ac150 [ 2613.401882] FS: 00007f39ef3dd8c0(0000) GS:ffff88041fb40000(0000) knlGS:0000000000000000 [ 2613.401885] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 2613.401887] CR2: 00000000023717c8 CR3: 00000002e7b34000 CR4: 00000000001406e0 [ 2613.401889] Call Trace: [ 2613.401912] intel_engine_is_idle+0x76/0x90 [i915] [ 2613.401931] i915_gem_wait_for_idle+0xe6/0x1e0 [i915] [ 2613.401951] fault_irq_set+0x40/0x90 [i915] [ 2613.401970] i915_ring_test_irq_set+0x42/0x50 [i915] [ 2613.401976] simple_attr_write+0xc7/0xe0 [ 2613.401981] full_proxy_write+0x4f/0x70 [ 2613.401987] __vfs_write+0x23/0x120 [ 2613.401992] ? rcu_read_lock_sched_held+0x75/0x80 [ 2613.401996] ? rcu_sync_lockdep_assert+0x2a/0x50 [ 2613.401999] ? __sb_start_write+0xfa/0x1f0 [ 2613.402004] vfs_write+0xc5/0x1d0 [ 2613.402008] ? trace_hardirqs_on_caller+0xe7/0x1c0 [ 2613.402013] SyS_write+0x44/0xb0 [ 2613.402020] entry_SYSCALL_64_fastpath+0x1c/0xb1 [ 2613.402022] RIP: 0033:0x7f39eded6670 [ 2613.402025] RSP: 002b:00007fffdcdcb1a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 2613.402030] RAX: ffffffffffffffda RBX: ffffffff81470203 RCX: 00007f39eded6670 [ 2613.402033] RDX: 0000000000000001 RSI: 000000000041bc33 RDI: 0000000000000006 [ 2613.402036] RBP: ffffc900084dff88 R08: 00007f39ef3dd8c0 R09: 0000000000000001 [ 2613.402038] R10: 0000000000000000 R11: 0000000000000246 R12: 000000000041bc33 [ 2613.402041] R13: 0000000000000006 R14: 0000000000000000 R15: 0000000000000000 [ 2613.402046] ? __this_cpu_preempt_check+0x13/0x20 [ 2613.402052] Code: 01 9b fa e0 0f ff e9 28 fe ff ff 80 3d 6a dd 0e 00 00 0f 85 29 fe ff ff 48 c7 c7 48 19 29 a0 c6 05 56 dd 0e 00 01 e8 da 9a fa e0 <0f> ff e9 0f fe ff ff b9 01 00 00 00 ba 01 00 00 00 44 89 e6 48 [ 2613.402199] ---[ end trace 31f0cfa93ab632bf ]--- Fixes: 25112b64 ("drm/i915: Wait for all engines to be idle as part of i915_gem_wait_for_idle()") Signed-off-by:
-
Chuanxiao Dong authored
Currently GVT-g cannot work properly when host GuC submission is enabled, so make the driver loading failed in this case. v2: - use DRM_ERROR as it is a fatal message. (Chris) Suggested-by:
Chuanxiao Dong <chuanxiao.dong@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Zhenyu Wang <zhenyuw@linux.intel.com> Reviewed-by:
-
Chuanxiao Dong authored
GVT-g relies on the enable_execlists parameter in i915. If this option is not enabled for GVT-g, should return -EIO to make i915 driver loading failed. v2: - Use DMR_ERROR as it is a fatal message. (Chris) Suggested-by:
-
Chuanxiao Dong authored
The intel_gvt_sanitize_options will sanitize the GVT related options before doing initialize the GVT. Suggested-by:
-
Chris Wilson authored
I have a plan to write a quick test to exercise concurrent usage of i915_gem_shrink(), the simplest way looks to be to have multiple threads using debugfs/i915_drop_caches. However, we currently take one lock over the entire function, serialising the calls into i915_gem_shrink() so reduce the lock coverage. Testcase: igt/gem_shrink/reclaim Signed-off-by:
-
Chris Wilson authored
Add kerneldoc for the vma_list stored on the i915_gem_object, in particular, documenting the expected ordering of elements -- i.e. that we do expect GGTT VMA first followed by the ppGTT VMA. Signed-off-by:
-
Maarten Lankhorst authored
SDVO was the last connector that's still using the legacy paths for properties, and this is with a reason! This connector implements a lot of properties dynamically, and some of them shared with the digital connector state, so sdvo_connector_state subclasses intel_digital_connector_state. set_property had a lot of validation, but this is handled in the drm core, so most of the validation can die off. The properties are written right before enabling the connector, since there is no good way to update the properties without crtc. Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-13-maarten.lankhorst@linux.intel.com
-
Maarten Lankhorst authored
Do the same as other connectors, attempt to detect hdmi audio in the detect() callback, and only use the force_audio property as override. Compute has_audio in pipe_config, and use that value instead of the probed value directly. Signed-off-by:
-
Maarten Lankhorst authored
intel_hdmi supports 3 properties, force_audio, broadcast rgb and scaling mode. The last one is only created for eDP, so the is_eDP in set_property is not required. panel fitting and broadcast rgb are straightforward and only requires changing compute_config. force_audio is also used to force DVI mode, which means changes to compute_config and mode_valid. mode_valid is called with connection_mutex held, so it can safely dereference connector->state. Signed-off-by:
-
Maarten Lankhorst authored
intel_dp supports 3 properties, scaling mode, broadcast rgb and force_audio. intel_digital_connector handles the plumbing, so we only have to hook this up in compute_config and init. Changes since v1: - Remove limited_color_range too, unused. (danvet) Signed-off-by:
-
