Make the sg_tablesize used by SRP adjustable at module load time via a
module parameter.  Calculate the corresponding IU length required to
support this.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Allow userspace to throttle traffic on a given connection to a target
port by adding "max_cmd_per_lun=xyz" to lower the cmd_per_lun value
set for that scsi_host.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Interrupts will always be enabled in srp_remove_one(), so
spin_lock_irq() can be used instead of spin_lock_irqsave().
Also, the loop takes target->scsi_host->host_lock, so target->state
can just be set to SRP_TARGET_REMOVED witout testing the old value.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Signed-off-by: Roland Dreier <rolandd@cisco.com>

The SRP driver never sleeps while holding target_mutex, and it's just
used to protect some simple list operations, so hold times will be
short.  So just convert it to a spinlock, which is smaller and faster.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

list_for_each_entry_safe() is used in one place where the list isn't
modified.  So just change it to list_for_each_entry().
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

SCAN_WILD_CARD is indeed available from <scsi/scsi.h>, which is
already included.  So get rid of private hack.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

The kernel has had wait_for_completion_timeout() for a long time now.
mthca should use it to handle FW commands timing out, instead of
implementing the same thing in a much more complicated way by using
wait_for_completion() along with a timer that does complete().
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Create an SRP FMR pool on HCAs that support FMRs, and use FMRs to map
gather/scatter lists that have more than one entry into a single
memory region that appears virtually contiguous to the SRP target
(which is the RDMA initiator).

This patch bails out on FMR mapping for SCSI commands where the
gather/scatter list cannot be mapped into a single FMR because there
are sub-page-sized entries in middle of the list.  An unaligned
start or end of the list is OK.

Based on a patch by Vu Pham <vuhuong@mellanox.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Kill some dead code in mthca_eq.c
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Kernel connection management agent over InfiniBand that connects based
on IP addresses.  The agent defines a generic RDMA connection
abstraction to support clients wanting to connect over different RDMA
devices.

The agent also handles RDMA device hotplug events on behalf of clients.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Add an address translation service that maps IP addresses to
InfiniBand GID addresses using IPoIB.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Export ip_dev_find() to allow locating a net_device given an IP address.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Extend matching connection requests to listens in the InfiniBand CM to
include private data checks.

This allows applications to listen on the same service identifier,
with private data directing the request to the appropriate application.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Provide common handling for marshalling data between userspace clients
and kernel InfiniBand drivers.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Memfree firmware is in rare cases reporting WQE index == base - 1 in
receive completion with error, instead of (rq size - 1); base is 0 in
mthca.  Here is a patch to avoid kernel crash and report a correct WR
id in this case.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

mthca does not restore the following PCI-X/PCI Express registers after reset:
  PCI-X device: PCI-X command register
  PCI-X bridge: upstream and downstream split transaction registers
  PCI Express : PCI Express device control and link control registers

This causes instability and/or bad performance on systems where one of
these registers is set to a non-default value by BIOS.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Being named "Crazed Snow-Weasel" instills a lot of confidence in this
release, so I'm sure this will be one of the better ones.

Reflect the fact that the Cell Broadband Engine supports 64k
pages by adding the bit to the CPU features.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The page size encoding passed to tlbie is incorrect for new-style
large pages.  This fixes it.  This doesn't affect anything on older
machines because mmu_psize_defs[psize].penc (the page size encoding)
is 0 for 4k and 16M pages (the two are distinguished by a separate "is
a large page" bit).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

arm_timer() checks PF_EXITING to prevent BUG_ON(->exit_state)
in run_posix_cpu_timers().

However, for some reason it does so only for CPUCLOCK_PERTHREAD
case (which is imho wrong).

Also, this check is not reliable, PF_EXITING could be set on
another cpu without any locks/barriers just after the check,
so it can't prevent from attaching the timer to the exiting
task.

The previous patch makes this check unneeded.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

do_exit() clears ->it_##clock##_expires, but nothing prevents
another cpu to attach the timer to exiting process after that.
arm_timer() tries to protect against this race, but the check
is racy.

After exit_notify() does 'write_unlock_irq(&tasklist_lock)' and
before do_exit() calls 'schedule() local timer interrupt can find
tsk->exit_state != 0. If that state was EXIT_DEAD (or another cpu
does sys_wait4) interrupted task has ->signal == NULL.

At this moment exiting task has no pending cpu timers, they were
cleanuped in __exit_signal()->posix_cpu_timers_exit{,_group}(),
so we can just return from irq.

John Stultz recently confirmed this bug, see

	http://marc.theaimsgroup.com/?l=linux-kernel&m=115015841413687Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

If the local timer interrupt happens just after do_exit() sets PF_EXITING
(and before it clears ->it_xxx_expires) run_posix_cpu_timers() will call
check_process_timers() with tasklist_lock + ->siglock held and

	check_process_timers:

		t = tsk;
		do {
			....

			do {
				t = next_thread(t);
			} while (unlikely(t->flags & PF_EXITING));
		} while (t != tsk);

the outer loop will never stop.

Actually, the window is bigger.  Another process can attach the timer
after ->it_xxx_expires was cleared (see the next commit) and the 'if
(PF_EXITING)' check in arm_timer() is racy (see the one after that).
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

A couple of fixes that should prevent crashes when using netconsole and
suspend/resume. First, netconsole poll routine shouldn't run unless the
device is up; second, the NAPI poll should be disabled during suspend.

This is only an issue on sky2, because it has to have one NAPI poll
routine for both ports on dual port boards. Normal drivers use
netif_rx_schedule_prep and that checks for netif_running.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

If get_user_pages() returns less pages than what we asked for, we jump
to out_unmap which will return ERR_PTR(ret).  But ret can contain a
positive number just smaller than local_nr_pages, so be sure to set it
to -EFAULT always.

Problem found and diagnosed by Damien Le Moal <damien@sdl.hitachi.co.jp>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Some time ago the cdrom open routine was changed so that we call the
driver's open routine before checking to see if it is read only.  However,
if we discovered that a read write open was not possible and the open
flags required a writable open, we just returned -EROFS without calling
the driver's release routine.   This seems to work for most cdrom drivers,
but breaks the Powerpc iSeries virtual cdrom rather badly.

This just inserts the release call in the error path to balance the call
to "->open()" done by "open_for_data()".
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

We don't clear the seek stat values in cfq_alloc_io_context(), and if
->seek_mean is unlucky enough to be set to -36 by chance, the first
invocation of cfq_update_io_seektime() will oops with a divide by zero
in do_div().

Just memset the entire cic instead of filling invididual values
independently.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

If flock_lock_file() failed to allocate flock with locks_alloc_lock()
then "error = 0" is returned. Need to return some non-zero.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The resume bug was caused not by an early interrupt but because the idle
timeout was not being stopped on suspend.  Also disable hardware IRQ's
on suspend.  Will need to revisit this with hotplug?
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The hardware should be fully shut off during suspend, and the base
irq mask restored during resume.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

If the poll routine detects no hardware available, it needs to dequeue
it self from the network poll list. Linus didn't understand NAPI.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

It is cleaner, to not loop over both ports if only one exists.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The set power state function is cleaner if it doesn't return anything.
The only caller that could fail is in suspend() and it can check the argument
there.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

From: Randy Dunlap <rdunlap@xenotime.net>

According to include/asm-alpha/bitops.h, only ALPHA_EV67 has hardware
hweight support, so ALPHA_EV6 needs to use GENERIC_HWEIGHT.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Ernst Herzberg <earny@net4u.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

shmem_rmdir() must undo the increment of i_nlink done in
shmem_get_inode() for directories, otherwise at least
IN_DELETE_SELF inotify event generation is broken.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

I noticed a strange behavior in a tmpfs file system the other day, while
building packages - occasionally, and seemingly at random, make decided to
rebuild a target. However, only on tmpfs.

A file would be created, and if checked, it had a sub-second timestamp.
However, after an utimes related call where sub-seconds should be set, they
were zeroed instead. In the case that a file was created, and utimes(...,NULL)
was used on it in the same second, the timestamp on the file moved backwards.

After some digging, I found that this was being caused by tmpfs not having a
time granularity set, thus inheriting the default 1 second granularity.

Hugh adds: yes, we missed tmpfs when the s_time_gran mods went into 2.6.11.
Unfortunately, the granularity of CURRENT_TIME, often used in filesystems,
does not match the default granularity set by alloc_super.  A few more such
discrepancies have been found, but this is the most important to fix now.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Do not double-export sys_close() when CONFIG_SOLARIS_EMUL_MODULE

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [IPV4]: Increment ipInHdrErrors when TTL expires.
  [TCP]: continued: reno sacked_out count fix
  [DCCP] Ackvec: fix soft lockup in ackvec handling code

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] Fix Integrator and Versatile interrupt initialisation
  [ARM] 3546/1: PATCH: subtle lost interrupts bug on i.MX
  [ARM] 3547/1: PXA-OHCI: Allow platforms to specify a power budget
  [ARM] Fix Neponset IRQ handling

Signed-off-by: Weidong <weid@nanjing-fnst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>