- 21 Sep, 2009 2 commits
-
-
Jesse Barnes authored
Add support for framebuffer compression on GM45 and above. Removes some unnecessary I915_HAS_FBC checks as well (this is now part of the FBC display function). Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net>
-
Jesse Barnes authored
This patch splits out several of the display functions into a separate display function table to avoid tons of chipset specific if..else if..else if blocks all over. There are more opportunities for this (some noted in the structure defintition); so more cleanup patches will follow. Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net>
-
- 18 Sep, 2009 3 commits
-
-
Chris Wilson authored
If the presumed_offset as feed to userspace and returned to the kernel from a previous execbuffer is still valid, then we do not need to rewrite the relocation entry and may skip the offset sanity checks. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Chris Wilson authored
Eric noted a potential concern with the low bits not being strictly used as part of the absolute offset (instead part of the command stream to the GPU), but in practice that should not be an issue. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Tested-by: Andy Whitcroft <apw@canonical.com> Cc: Eric Anholt <eric@anholt.net> CC: stable@kernel.org Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Jesse Barnes authored
We usually don't have an SAREA, and we always want to update the FBC status anyway, so move the update up above the various master/sarea checks. Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
- 17 Sep, 2009 26 commits
-
-
Jesse Barnes authored
It reports closed when open, leading to "no outputs found" at startup unless a VGA cable is plugged in. Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Jesse Barnes authored
Yakui pointed out that we don't properly no-op the ACPI button routines if the button driver isn't built in. This will cause problems if ACPI is disabled, so provide stub functions in that case. Reported-by: ykzhao <yakui.zhao@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Jesse Barnes authored
A very high dotclock (e.g. 229500kHz as reported by Anton) can cause the entries_required variable to overflow, potentially leading to a FIFO watermark value that's too low to support the given mode. Split the division across the calculation to avoid this. Cc: stable@kernel.org Reported-by: Anton Khirnov <wyskas@gmail.com> Tested-by: Anton Khirnov <wyskas@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Jaswinder Singh Rajput authored
By handling latency variable efficiently we also get rid of this warning : CC [M] drivers/gpu/drm/i915/intel_display.o drivers/gpu/drm/i915/intel_display.c: In function ‘igd_enable_cxsr’: drivers/gpu/drm/i915/intel_display.c:1918: warning: ‘latency’ may be used uninitialized in this function Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Zhenyu Wang authored
Don't need extra config restore like for intel_agp, which might cause resume hang issue found by Alan on 845G. Cc: Stable Team <stable@kernel.org> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Chris Wilson authored
Due to the necessity of having to take the struct_mutex, the i915 shrinker can not free the inactive lists if we fail to allocate memory whilst processing a batch buffer, triggering an OOM and an ENOMEM that is reported back to userspace. In order to fare better under such circumstances we need to manually retry a failed allocation after evicting inactive buffers. To do so involves 3 steps: 1. Marking the backing shm pages as NORETRY. 2. Updating the get_pages() callers to evict something on failure and then retry. 3. Revamping the evict something logic to be smarter about the required buffer size and prefer to use volatile or clean inactive pages. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Chris Wilson authored
Similar to the madvise() concept, the application may wish to mark some data as volatile. That is in the event of memory pressure the kernel is free to discard such buffers safe in the knowledge that the application can recreate them on demand, and is simply using these as a cache. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Chris Wilson authored
This should help GEM handle memory pressure sitatuions more gracefully. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Chris Wilson authored
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Chris Wilson authored
There is no need to store the gtt_alignment as it is either explicitly set according to the hardware requirements (e.g. scanout) or the minimum alignment is computed on demand. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Chris Wilson authored
If we failed to set the domain, the buffer was no longer being tracked on any list. Cc: stable@kernel.org Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Jesse Barnes authored
Due to a bogus FBC support check and failing to check for FBC support in the right places, mode setting on non-mobile platforms could fail and hang in the FBC disable routine. Fix it up. This fix highlights the need for cleanups in this area (function pointers and better feature support checks). Patches for that to follow. Tested-by: Kenny Graunke <kenny@whitecape.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Jesse Barnes authored
We now unconditionally restore the mode at lid open time since some platforms turn off the panel, pipes or other display elements when the lid is closed. There's a problem with doing this at resume time however. At resume time, we'll get a lid event, but restoring the mode at that time may not be safe (e.g. if we get the lid event before global state has been restored), so check the suspended state and make sure our restore is locked against other mode updates. Tested-by: Ben Gamari <bgamari.foss@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Ben Gamari authored
There is a very real possibility that multiple CPUs will notice that the GPU is wedged. This introduces all sorts of potential race conditions. Make the wedged flag atomic to mitigate this risk. Signed-off-by: Ben Gamari <bgamari.foss@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Ben Gamari authored
This patch uses the previously introduced chip reset logic to reset the chip when an error event is detected. Signed-off-by: Ben Gamari <bgamari.foss@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Ben Gamari authored
This patch puts in place the machinery to attempt to reset the GPU. This will be used when attempting to recover from a GPU hang. Signed-off-by: Owain G. Ainsworth <oga@openbsd.org> Signed-off-by: Ben Gamari <bgamari.foss@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Ben Gamari authored
We set a periodic timer to check on the GPU, resetting it every time a batch is completed. If the timer elapses, we check acthd. If acthd hasn't changed in two timer periods, we assume the chip is wedged. This is implemented in such a way that it leaves the option open to employ adaptive timer intervals in the future. One could wait until several timer periods have elapsed before declaring the chip dead. If the chip comes back after several periods but before the "dead" threshold, the timer interval or dead threshold could be raised. It is important to note that while checking for active requests, we need to account for the fact that requests are removed from the list (i.e. retired) in a deferred work queue handler. This means that merely checking for an empty request_list is insufficient; the list could be non-empty yet the GPU still idle, causing the hangcheck timer to incorrectly mark the GPU as wedged (it took me a while to figure that out---sigh...) Signed-off-by: Ben Gamari <bgamari.foss@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Ben Gamari authored
We'll need it in i915_irq.c for checking whether there are outstanding requests. Also, the function really ought to return a bool, not an int. Signed-off-by: Ben Gamari <bgamari.foss@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Ben Gamari authored
We move the display-specific code into it's own functions, called from the general GPU state save/restore functions. This will be needed later by the GPU reset code. Signed-off-by: Ben Gamari <bgamari.foss@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Ben Gamari authored
i915_wait_request() only checks mm.wedged after it interacts with the hardware, generally causing the driver to lock up waiting for a wedged chip. Make sure we check mm.wedged as the first thing we do. Reported-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ben Gamari <bgamari.foss@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Li Peng authored
BLC_PWM_CTL2 is for 965+ only, so add device model check for legacy backlight control. For native backlight control, it maps the backlight value (0~255) in opregion ASLE[BCLP] to backlight duty cycle (0~max_backlight) and set into control register. It also add support for IGD device, which follows opregion spec. Signed-off-by: Li Peng <peng.li@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Zhenyu Wang authored
Arrandale has new window based method for panel fitting. This one enables full screen aspect scaling on LVDS. It fixes standard mode display failure on LVDS for Arrandale. Cc: Stable Team <stable@kernel.org> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Zhenyu Wang authored
This is not required on newer stepping hardware to get reliable force detect status. Removing this fixes screen blank flicker in CRT detect on IGDNG. Cc: Stable Team <stable@kernel.org> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Zhenyu Wang authored
IGDNG LVDS SSC uses 120Mhz freq. This fixes one 1600x900 LVDS panel black issue on IGDNG with SSC enabled. Cc: Stable Team <stable@kernel.org> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Zhenyu Wang authored
New register for PCH LVDS on IGDNG should be used. This is a copy-n-paste typo. This fixes possible dual channel LVDS panel failure on IGDNG. Cc: Stable Team <stable@kernel.org> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
Jesse Barnes authored
We want the compressed line length buffer address, not the framebuffer address. Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
- 11 Sep, 2009 3 commits
-
-
Chris Wilson authored
drm_ht_remove_item() does not handle removing an absent item and the hlist in particular is incorrectly initialised. The easy remedy is simply skip calling i915_gem_free_mmap_offset() unless we have actually created the offset and associated ht entry. This also fixes the mishandling of a partially constructed offset which leaves pointers initialized after freeing them along the i915_gem_create_mmap_offset() error paths. In particular this should fix the oops found here: https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-intel/+bug/415357/comments/8Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Eric Anholt <eric@anholt.net> Cc: stable@kernel.org
-
Eric Anholt authored
Ever since we enabled GEM, the pre-9xx chipsets (particularly 865) have had serious stability issues. Back in May a wbinvd was added to the DRM to work around much of the problem. Some failure remained -- easily visible by dragging a window around on an X -retro desktop, or by looking at bugzilla. The chipset flush was on the right track -- hitting the right amount of memory, and it appears to be the only way to flush on these chipsets, but the flush page was mapped uncached. As a result, the writes trying to clear the writeback cache ended up bypassing the cache, and not flushing anything! The wbinvd would flush out other writeback data and often cause the data we wanted to get flushed, but not always. By removing the setting of the page to UC and instead just clflushing the data we write to try to flush it, we get the desired behavior with no wbinvd. This exports clflush_cache_range(), which was laying around and happened to basically match the code I was otherwise going to copy from the DRM. Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org> Cc: stable@kernel.org
-
Jesse Barnes authored
This patch adds framebuffer compression (good for about ~0.5W power savings in the best case) support for pre-GM45 chips. GM45+ have a new, more flexible FBC scheme that will be added in a separate patch. FBC can't always be enabled: the compressed buffer must be physically contiguous and reside in stolen space. So if you have a large display and a small amount of stolen memory, you may not be able to take advantage of FBC. In some cases, a BIOS setting controls how much stolen space is available. Increasing this to 8 or 16M can help. Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net>
-
- 10 Sep, 2009 6 commits
-
-
Jesse Barnes authored
With all the other lid pieces in place, it's easy to generate a uevent for the LVDS connector just like we do for other outputs. Should make lid open/close fit in with the rest of a userland based output reconfiguration scheme. Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net>
-
Jesse Barnes authored
We can't load or hotplug detect LVDS like we can other outputs, but if there's a lid device present we can use it as a proxy. This allows the LFP state to be determined at ->detect time, making configurations requiring manual intervention today "just work" assuming the lid device status is correct. Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net>
-
Jesse Barnes authored
Some laptop platforms will disable pipes and/or planes at lid close time and not restore them when the lid is opened again. So catch the lid event, and if the lid was opened, force a mode restore. Fixes fdo bug #21230. Acked-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net>
-
Jesse Barnes authored
Some drivers need to know when a lid event occurs and get the current status. This can be useful for when a platform firmware clobbers some hardware state at lid time, and a driver needs to restore things when the lid is opened again. Acked-by: Matthew Garrett <mjg59@srcf.ucam.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net>
-
Li Peng authored
Test on the IGD chip, which is a G33-like graphic device. Signed-off-by: Li Peng <peng.li@intel.com> Signed-off-by: Eric Anholt <eric@anholt.net>
-
Zhao Yakui authored
When the output device is LVDS, maybe the pixel clock of adjusted_mode will be less than that in mode. In such case it will set the incorrect multipler factor in DPLL_MD register. So the dpll_md_reg will be reset when the output type is non-SDVO https://bugs.freedesktop.org/show_bug.cgi?id=22761Signed-off-by: Zhao Yakui <yakui.zhao@intel.com> Reviewd-by: Eric Anholt <eric@anholt.net> Signed-off-by: Eric Anholt <eric@anholt.net>
-