These are a PM core fix and an OPP framework fix for 4.18-rc2,
both "stable" material.

* pm-core:
  PM / core: Fix supplier device runtime PM usage counter imbalance

* pm-opp:
  PM / OPP: Update voltage in case freq == old_freq

Fix a typo in the intel_pstate admin-guide documentation.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull an OPP fix for 4.18-rc2 from Viresh Kumar.

* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
  PM / OPP: Update voltage in case freq == old_freq

This commit fixes a rare but possible case when the clk rate is updated
without update of the regulator voltage.

At boot up, CPUfreq checks if the system is running at the right freq. This
is a sanity check in case a bootloader set clk rate that is outside of freq
table present with cpufreq core. In such cases system can be unstable so
better to change it to a freq that is preset in freq-table.

The CPUfreq takes next freq that is >= policy->cur and this is our
target_freq that needs to be set now.

dev_pm_opp_set_rate(dev, target_freq) checks the target_freq and the
old_freq (a current rate). If these are equal it returns early. If not,
it searches for OPP (old_opp) that fits best to old_freq (not listed in
the table) and updates old_freq (!).

Here, we can end up with old_freq = old_opp.rate = target_freq, which
is not handled in _generic_set_opp_regulator(). It's supposed to update
voltage only when freq > old_freq  || freq > old_freq.

if (freq > old_freq) {
		ret = _set_opp_voltage(dev, reg, new_supply);
[...]
if (freq < old_freq) {
		ret = _set_opp_voltage(dev, reg, new_supply);
		if (ret)

It results in, no voltage update while clk rate is updated.

Example:
freq-table = {
	1000MHz   1.15V
	 666MHZ   1.10V
	 333MHz   1.05V
}
boot-up-freq        = 800MHz   # not listed in freq-table
freq = target_freq  = 1GHz
old_freq            = 800Mhz
old_opp = _find_freq_ceil(opp_table, &old_freq);  #(old_freq is modified!)
old_freq            = 1GHz

Fixes: 6a0712f6 ("PM / OPP: Add dev_pm_opp_set_rate()")
Cc: 4.6+ <stable@vger.kernel.org> # v4.6+
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>

When scaling max/min settings are changed, internally they are converted
to a ratio using the max turbo 1 core turbo frequency. This works fine
when 1 core max is same irrespective of the core. But under Turbo 3.0,
this will not be the case. For example:
Core 0: max turbo pstate: 43 (4.3GHz)
Core 1: max turbo pstate: 45 (4.5GHz)
In this case 1 core turbo ratio will be maximum of all, so it will be
45 (4.5GHz). Suppose scaling max is set to 4GHz (ratio 40) for all cores
,then on core one it will be
 = max_state * policy->max / max_freq;
 = 43 * (4000000/4500000) = 38 (3.8GHz)
 = 38
which is 200MHz less than the desired.
On core2, it will be correctly set to ratio 40 (4GHz). Same holds true
for scaling min frequency limit. So this requires usage of correct turbo
max frequency for core one, which in this case is 4.3GHz. So we need to
adjust per CPU cpu->pstate.turbo_freq using the maximum HWP ratio of that
core.

This change uses the HWP capability of a core to adjust max turbo
frequency. But since Broadwell HWP doesn't use ratios in the HWP
capabilities, we have to use legacy max 1 core turbo ratio. This is not
a problem as the HWP capabilities don't differ among cores in Broadwell.
We need to check for non Broadwell CPU model for applying this change,
though.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Add device remove and module exit code to make the driver
functioning as a loadable module.

Fixes: ac289276 (cpufreq: kryo: allow building as a loadable module)
Signed-off-by: Ilia Lin <ilia.lin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

In event of error returned by the nvmem_cell_read() non-pointer value
may be dereferenced. Fix this with error handling.
Additionally free the allocated speedbin buffer, as per the API.

Fixes: 9ce36edd1a52 (cpufreq: Add Kryo CPU scaling driver)
Signed-off-by: Ilia Lin <ilia.lin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull block fixes from Jens Axboe:
 "A collection of fixes that should go into -rc1. This contains:

   - bsg_open vs bsg_unregister race fix (Anatoliy)

   - NVMe pull request from Christoph, with fixes for regressions in
     this window, FC connect/reconnect path code unification, and a
     trace point addition.

   - timeout fix (Christoph)

   - remove a few unused functions (Christoph)

   - blk-mq tag_set reinit fix (Roman)"

* tag 'for-linus-20180616' of git://git.kernel.dk/linux-block:
  bsg: fix race of bsg_open and bsg_unregister
  block: remov blk_queue_invalidate_tags
  nvme-fabrics: fix and refine state checks in __nvmf_check_ready
  nvme-fabrics: handle the admin-only case properly in nvmf_check_ready
  nvme-fabrics: refactor queue ready check
  blk-mq: remove blk_mq_tagset_iter
  nvme: remove nvme_reinit_tagset
  nvme-fc: fix nulling of queue data on reconnect
  nvme-fc: remove reinit_request routine
  blk-mq: don't time out requests again that are in the timeout handler
  nvme-fc: change controllers first connect to use reconnect path
  nvme: don't rely on the changed namespace list log
  nvmet: free smart-log buffer after use
  nvme-rdma: fix error flow during mapping request data
  nvme: add bio remapping tracepoint
  nvme: fix NULL pointer dereference in nvme_init_subsystem
  blk-mq: reinit q->tag_set_list entry only after grace period

Pull documentation fixes from Mauro Carvalho Chehab:
 "This solves a series of broken links for files under Documentation,
  and improves a script meant to detect such broken links (see
  scripts/documentation-file-ref-check).

  The changes on this series are:

   - can.rst: fix a footnote reference;

   - crypto_engine.rst: Fix two parsing warnings;

   - Fix a lot of broken references to Documentation/*;

   - improve the scripts/documentation-file-ref-check script, in order
     to help detecting/fixing broken references, preventing
     false-positives.

  After this patch series, only 33 broken references to doc files are
  detected by scripts/documentation-file-ref-check"

* tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental: (26 commits)
  fix a series of Documentation/ broken file name references
  Documentation: rstFlatTable.py: fix a broken reference
  ABI: sysfs-devices-system-cpu: remove a broken reference
  devicetree: fix a series of wrong file references
  devicetree: fix name of pinctrl-bindings.txt
  devicetree: fix some bindings file names
  MAINTAINERS: fix location of DT npcm files
  MAINTAINERS: fix location of some display DT bindings
  kernel-parameters.txt: fix pointers to sound parameters
  bindings: nvmem/zii: Fix location of nvmem.txt
  docs: Fix more broken references
  scripts/documentation-file-ref-check: check tools/*/Documentation
  scripts/documentation-file-ref-check: get rid of false-positives
  scripts/documentation-file-ref-check: hint: dash or underline
  scripts/documentation-file-ref-check: add a fix logic for DT
  scripts/documentation-file-ref-check: accept more wildcards at filenames
  scripts/documentation-file-ref-check: fix help message
  media: max2175: fix location of driver's companion documentation
  media: v4l: fix broken video4linux docs locations
  media: dvb: point to the location of the old README.dvb-usb file
  ...

Pull fsnotify updates from Jan Kara:
 "fsnotify cleanups unifying handling of different watch types.

  This is the shortened fsnotify series from Amir with the last five
  patches pulled out. Amir has modified those patches to not change
  struct inode but obviously it's too late for those to go into this
  merge window"

* tag 'fsnotify_for_v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  fsnotify: add fsnotify_add_inode_mark() wrappers
  fanotify: generalize fanotify_should_send_event()
  fsnotify: generalize send_to_group()
  fsnotify: generalize iteration of marks by object type
  fsnotify: introduce marks iteration helpers
  fsnotify: remove redundant arguments to handle_event()
  fsnotify: use type id to identify connector object type

Pull fbdev updates from Bartlomiej Zolnierkiewicz:
 "There is nothing really major here, few small fixes, some cleanups and
  dead drivers removal:

   - mark omapfb drivers as orphans in MAINTAINERS file (Tomi Valkeinen)

   - add missing module license tags to omap/omapfb driver (Arnd
     Bergmann)

   - add missing GPIOLIB dependendy to omap2/omapfb driver (Arnd
     Bergmann)

   - convert savagefb, aty128fb & radeonfb drivers to use msleep & co.
     (Jia-Ju Bai)

   - allow COMPILE_TEST build for viafb driver (media part was reviewed
     by media subsystem Maintainer)

   - remove unused MERAM support from sh_mobile_lcdcfb and shmob-drm
     drivers (drm parts were acked by shmob-drm driver Maintainer)

   - remove unused auo_k190xfb drivers

   - misc cleanups (Souptick Joarder, Wolfram Sang, Markus Elfring, Andy
     Shevchenko, Colin Ian King)"

* tag 'fbdev-v4.18' of git://github.com/bzolnier/linux: (26 commits)
  fb_omap2: add gpiolib dependency
  video/omap: add module license tags
  MAINTAINERS: make omapfb orphan
  video: fbdev: pxafb: match_string() conversion fixup
  video: fbdev: nvidia: fix spelling mistake: "scaleing" -> "scaling"
  video: fbdev: fix spelling mistake: "frambuffer" -> "framebuffer"
  video: fbdev: pxafb: Convert to use match_string() helper
  video: fbdev: via: allow COMPILE_TEST build
  video: fbdev: remove unused sh_mobile_meram driver
  drm: shmobile: remove unused MERAM support
  video: fbdev: sh_mobile_lcdcfb: remove unused MERAM support
  video: fbdev: remove unused auo_k190xfb drivers
  video: omap: Improve a size determination in omapfb_do_probe()
  video: sm501fb: Improve a size determination in sm501fb_probe()
  video: fbdev-MMP: Improve a size determination in path_init()
  video: fbdev-MMP: Delete an error message for a failed memory allocation in two functions
  video: auo_k190x: Delete an error message for a failed memory allocation in auok190x_common_probe()
  video: sh_mobile_lcdcfb: Delete an error message for a failed memory allocation in two functions
  video: sh_mobile_meram: Delete an error message for a failed memory allocation in sh_mobile_meram_probe()
  video: fbdev: sh_mobile_meram: Drop SUPERH platform dependency
  ...

Pull AFS updates from Al Viro:
 "Assorted AFS stuff - ended up in vfs.git since most of that consists
  of David's AFS-related followups to Christoph's procfs series"

* 'afs-proc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  afs: Optimise callback breaking by not repeating volume lookup
  afs: Display manually added cells in dynamic root mount
  afs: Enable IPv6 DNS lookups
  afs: Show all of a server's addresses in /proc/fs/afs/servers
  afs: Handle CONFIG_PROC_FS=n
  proc: Make inline name size calculation automatic
  afs: Implement network namespacing
  afs: Mark afs_net::ws_cell as __rcu and set using rcu functions
  afs: Fix a Sparse warning in xdr_decode_AFSFetchStatus()
  proc: Add a way to make network proc files writable
  afs: Rearrange fs/afs/proc.c to remove remaining predeclarations.
  afs: Rearrange fs/afs/proc.c to move the show routines up
  afs: Rearrange fs/afs/proc.c by moving fops and open functions down
  afs: Move /proc management functions to the end of the file

Pull compat updates from Al Viro:
 "Some biarch patches - getting rid of assorted (mis)uses of
  compat_alloc_user_space().

  Not much in that area this cycle..."

* 'work.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  orangefs: simplify compat ioctl handling
  signalfd: lift sigmask copyin and size checks to callers of do_signalfd4()
  vmsplice(): lift importing iovec into vmsplice(2) and compat counterpart

Pull aio fixes from Al Viro:
 "Assorted AIO followups and fixes"

* 'work.aio' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  eventpoll: switch to ->poll_mask
  aio: only return events requested in poll_mask() for IOCB_CMD_POLL
  eventfd: only return events requested in poll_mask()
  aio: mark __aio_sigset::sigmask const

Pull networking fixes from David Miller:

 1) Various netfilter fixlets from Pablo and the netfilter team.

 2) Fix regression in IPVS caused by lack of PMTU exceptions on local
    routes in ipv6, from Julian Anastasov.

 3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.

 4) Don't crash on poll in TLS, from Daniel Borkmann.

 5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
    including Avahi mDNS. From Bart Van Assche.

 6) Missing of_node_put in qcom/emac driver, from Yue Haibing.

 7) We lack checking of the TCP checking in one special case during SYN
    receive, from Frank van der Linden.

 8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.

 9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.

10) Must grab HW caps before doing quirk checks in stmmac driver, from
    Jose Abreu.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
  net: stmmac: Run HWIF Quirks after getting HW caps
  neighbour: skip NTF_EXT_LEARNED entries during forced gc
  net: cxgb3: add error handling for sysfs_create_group
  tls: fix waitall behavior in tls_sw_recvmsg
  tls: fix use-after-free in tls_push_record
  l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
  l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
  mlxsw: spectrum_switchdev: Fix port_vlan refcounting
  mlxsw: spectrum_router: Align with new route replace logic
  mlxsw: spectrum_router: Allow appending to dev-only routes
  ipv6: Only emit append events for appended routes
  stmmac: added support for 802.1ad vlan stripping
  cfg80211: fix rcu in cfg80211_unregister_wdev
  mac80211: Move up init of TXQs
  mac80211_hwsim: fix module init error paths
  cfg80211: initialize sinfo in cfg80211_get_station
  nl80211: fix some kernel doc tag mistakes
  hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
  rds: avoid unenecessary cong_update in loop transport
  l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
  ...

Pull module updates from Jessica Yu:
 "Minor code cleanup and also allow sig_enforce param to be shown in
  sysfs with CONFIG_MODULE_SIG_FORCE"

* tag 'modules-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
  module: Allow to always show the status of modsign
  module: Do not access sig_enforce directly

Pull uml updates from Richard Weinberger:
 "Minor updates for UML:

   - fixes for our new vector network driver by Anton

   - initcall cleanup by Alexander

   - We have a new mailinglist, sourceforge.net sucks"

* 'for-linus-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Fix raw interface options
  um: Fix initialization of vector queues
  um: remove uml initcalls
  um: Update mailing list address

Merge tag 'riscv-for-linus-4.18-merge_window' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux

Pull RISC-V updates from Palmer Dabbelt:
 "This contains some small RISC-V updates I'd like to target for 4.18.

  They are all fairly small this time. Here's a short summary, there's
  more info in the commits/merges:

   - a fix to __clear_user to respect the passed arguments.

   - enough support for the perf subsystem to work with RISC-V's ISA
     defined performance counters.

   - support for sparse and cleanups suggested by it.

   - support for R_RISCV_32 (a relocation, not the 32-bit ISA).

   - some MAINTAINERS cleanups.

   - the addition of CONFIG_HVC_RISCV_SBI to our defconfig, as it's
     always present.

  I've given these a simple build+boot test"

* tag 'riscv-for-linus-4.18-merge_window' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
  RISC-V: Add CONFIG_HVC_RISCV_SBI=y to defconfig
  RISC-V: Handle R_RISCV_32 in modules
  riscv/ftrace: Export _mcount when DYNAMIC_FTRACE isn't set
  riscv: add riscv-specific predefines to CHECKFLAGS
  riscv: split the declaration of __copy_user
  riscv: no __user for probe_kernel_address()
  riscv: use NULL instead of a plain 0
  perf: riscv: Add Document for Future Porting Guide
  perf: riscv: preliminary RISC-V support
  MAINTAINERS: Update Albert's email, he's back at Berkeley
  MAINTAINERS: Add myself as a maintainer for SiFive's drivers
  riscv: Fix the bug in memory access fixup code

Pull more kvm updates from Paolo Bonzini:
 "Mostly the PPC part of the release, but also switching to Arnd's fix
  for the hyperv config issue and a typo fix.

  Main PPC changes:

   - reimplement the MMIO instruction emulation

   - transactional memory support for PR KVM

   - improve radix page table handling"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (63 commits)
  KVM: x86: VMX: redo fix for link error without CONFIG_HYPERV
  KVM: x86: fix typo at kvm_arch_hardware_setup comment
  KVM: PPC: Book3S PR: Fix failure status setting in tabort. emulation
  KVM: PPC: Book3S PR: Enable use on POWER9 bare-metal hosts in HPT mode
  KVM: PPC: Book3S PR: Don't let PAPR guest set MSR hypervisor bit
  KVM: PPC: Book3S PR: Fix failure status setting in treclaim. emulation
  KVM: PPC: Book3S PR: Fix MSR setting when delivering interrupts
  KVM: PPC: Book3S PR: Handle additional interrupt types
  KVM: PPC: Book3S PR: Enable kvmppc_get/set_one_reg_pr() for HTM registers
  KVM: PPC: Book3S: Remove load/put vcpu for KVM_GET_REGS/KVM_SET_REGS
  KVM: PPC: Remove load/put vcpu for KVM_GET/SET_ONE_REG ioctl
  KVM: PPC: Move vcpu_load/vcpu_put down to each ioctl case in kvm_arch_vcpu_ioctl
  KVM: PPC: Book3S PR: Enable HTM for PR KVM for KVM_CHECK_EXTENSION ioctl
  KVM: PPC: Book3S PR: Support TAR handling for PR KVM HTM
  KVM: PPC: Book3S PR: Add guard code to prevent returning to guest with PR=0 and Transactional state
  KVM: PPC: Book3S PR: Add emulation for tabort. in privileged state
  KVM: PPC: Book3S PR: Add emulation for trechkpt.
  KVM: PPC: Book3S PR: Add emulation for treclaim.
  KVM: PPC: Book3S PR: Restore NV regs after emulating mfspr from TM SPRs
  KVM: PPC: Book3S PR: Always fail transactions in guest privileged state
  ...

Pull virtio updates from Michael Tsirkin:
 "virtio, vhost: features, fixes

   - PCI virtual function support for virtio

   - DMA barriers for virtio strong barriers

   - bugfixes"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio: update the comments for transport features
  virtio_pci: support enabling VFs
  vhost: fix info leak due to uninitialized memory
  virtio_ring: switch to dma_XX barriers for rpmsg

As files move around, their previous links break. Fix the
references for them.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

The old HOWTO was removed a long time ago. The flat table
version is not metioned elsewhere, so just get rid of the
text.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

This file doesn't exist anymore:
	Documentation/cpu-freq/user-guide.txt

As the ABI already points to Documentation/cpu-freq, just
remove the broken link and the associated text.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

As files got renamed, their references broke.

Manually fix a series of broken refs at the DT bindings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

Rename:
	pinctrl-binding.txt -> pinctrl-bindings.txt

In order to match the current name of this file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

There were some file movements that changed the location for
some DT bindings. Fix them with:
	scripts/documentation-file-ref-check --fix

After manually checking if the new file makes sense.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

The specified locations are not right. Fix the wildcard logic
to point to the correct directories.

Without that, get-maintainer won't get things right:

	$ ./scripts/get_maintainer.pl --no-git-fallback --no-r --no-n --no-l -f Documentation/devicetree/bindings/arm/cpu-enable-method/nuvoton,npcm750-smp
	robh+dt@kernel.org (maintainer:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS)
	mark.rutland@arm.com (maintainer:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS)

After the patch, it will properly point to NPCM arch maintainers:
	$ ./scripts/get_maintainer.pl --no-git-fallback --no-r --no-n --no-l -f Documentation/devicetree/bindings/arm/cpu-enable-method/nuvoton,npcm750-smp
	avifishman70@gmail.com (supporter:ARM/NUVOTON NPCM ARCHITECTURE)
	tmaimon77@gmail.com (supporter:ARM/NUVOTON NPCM ARCHITECTURE)
	robh+dt@kernel.org (maintainer:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS)
	mark.rutland@arm.com (maintainer:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS)

Cc: Avi Fishman <avifishman70@gmail.com>
Cc: Tomer Maimon <tmaimon77@gmail.com>
Cc: Patrick Venture <venture@google.com>
Cc: Nancy Yuen <yuenn@google.com>
Cc: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

Those files got a manufacturer's name prepended and were moved around.
Adjust their references accordingly.

Also, due those movements, Documentation/devicetree/bindings/video
doesn't exist anymore.

Cc: David Airlie <airlied@linux.ie>
Cc: David Lechner <david@lechnology.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

The alsa parameters file was renamed to alsa-configuration.rst.

With regards to OSS, it got retired as a hole by  at changeset
727dede0 ("sound: Retire OSS"). So, it doesn't make sense
to keep mentioning it at kernel-parameters.txt.

Fixes: 727dede0 ("sound: Retire OSS")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

The location pointed there is missing "bindings/" on its path.
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

As we move stuff around, some doc references are broken. Fix some of
them via this script:
	./scripts/documentation-file-ref-check --fix

Manually checked that produced results are valid.
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

Some files, like tools/memory-model/README has references to
a Documentation file that is locale to it. Handle references
that are relative to them too.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

Now that the number of broken refs are smaller, improve the logic
that gets rid of false-positives.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

Sometimes, people use dash instead of underline or vice-versa.
Try to autocorrect it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

There are several links broken due to DT file movements. Add
a hint logic to seek for those changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

at MAINTAINERS, some filename paths use '?' and things like [7,9].
So, accept more wildcards, in order to avoid false-positives.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

The name of the --fix option was renamed, but it was not
changed at the quick help message.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

There's a missing ".rst" at the doc's file name.
Acked-by: Ramesh Shanmugasundaram <Ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>

There are several places pointing to old documentation files:

  Documentation/video4linux/API.html
  Documentation/video4linux/bttv/
  Documentation/video4linux/cx2341x/fw-encoder-api.txt
  Documentation/video4linux/m5602.txt
  Documentation/video4linux/v4l2-framework.txt
  Documentation/video4linux/videobuf
  Documentation/video4linux/Zoran

Make them point to the new location where available, removing
otherwise.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>