When the interface does not have carrier but when it's put into
loopback mode (for tests), it does not make sense to not have
the carrier. So force it!
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains updates to ixgbe and e1000e.  The ixgbe patches are
a mix of fixes, cleanup and added functionality.  The first fix is for
traffic classes, where if the mapping has changed reset the NIC.  The other
ixgbe fix resolves an issue where the device lookup neglected to do a
pci_dev_put() to decrement the device reference count.

The ixgbe cleanup was done by Josh, where the auto-negotiation variables
were renamed/cleaned up and refactored.

The remaining patches are from Bruce to do additional cleanup on e1000e as
well as bump the driver version.  Most notably is the cleanup to use the
kernel IEEE MII definitions where possible instead of the local MII
definitions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

For standard IEEE MII-compatible transceivers, the kernel has generic
register and bit definitions.  Use those instead of redundant local
defines.

Do not replace references of MII_CR_SPEED_10 with BMCR_SPEED10 (0x0000)
when it is not necessary (i.e. when it is bitwise OR'ed with another
value).

Some whitespace issues in the surrounding context of the above changes are
also cleaned up.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the unused parameter when possible, otherwise use __always_unused
attribute.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

For clarity, wrap OR'ed bit settings with parentheses.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove redundant defines which are defined elsewhere.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Removes the autoneg parameter from the setup_link functions.
Adds local variable autoneg to setup_link functions to be passed
to get_link_capabilities functions if needed.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>

Removes the autoneg parameter from the setup_link_speed functions.  These
functions do nothing with this parameter.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Renames some autoneg/speed variables to be more consistent with check_link,
get_link_capabilities, and setup_link function calls. Initializes instances
of autoneg.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The device lookup neglected to do a pci_dev_put() to decrement the
device reference count.
Reported-by: Elena Gurevich <elena.gurevich@toganetworks.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Check for up2tc change and call ixgbe_dcbnl_devreset() if the mapping has
changed but the number of TC's in use has not changed.
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Merge mlx4 bug fixes from Amir Vadai.
Signed-off-by: David S. Miller <davem@davemloft.net>

Under heavy CPU load, changing, ring size/mtu/etc. could result in transmit
timeout, since stop-start port might take more than 10 seconds.
Calling netif_detach_device to prevent tx queue transmit timeout.

netif_detach_device() is not called under ndo_stop, because netif_carrier_off
will prevent the timeout, and device should not be marked as not present, or
else user won't be able to start it later on.

CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mac reassignments should only be done when not supported by the firmware. To
accomplish that, checking firmware capability bit to know whether we should
reassign macs in the driver.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Firmware dynamically changes flow steering hash configuration from covering
L2 only to "full" L2/L3/L4 mode needed.  The dynamic change allows the driver
to set hard coded hash configuration which is changed by the firmware from L2
to L2/L3/L4 when attaching the first L3/L4 flow steering rule and back to L2
when there are no more such rules.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As part of the driver unload flow, all steering rules must be deleted,
make sure to remove the rules that were set through ethtool.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Attaching steering rules while the interface is down is an invalid operation, block it.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The vlan mask field should be validated and assigned according to the field
size which is 12 bits. Also replace the numeric 0xfff mask with existing kernel
macro.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When attaching flow steering rules via Ethtool accept only valid vlans IDs e.g
in the range: [0,4095].
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Destination mac is a mandatory specification for ip/udp steering rules.
When attaching multicast steering rules via ethtool the unicast mac of the
interface was added to the rule specification instead of the multicast mac.
The following commit sets the corresponding multicast mac for the rule multicast ip.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The allow_loopback flag was wrongly set using arithmetic bit operation, change
the code to use logical bit operation.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some of the fields for struct mlx4_net_trans_rule_hw_ctrl were packed into u32
and accessed through bit field operations. Expose and access them directly as
u8.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement ethtool get_drvinfo.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since all users are write-lock, it does not make sense to use
rwlock here.  Use simple spinlock.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Supporting access to skb->pkt_type is a bit tricky if we want
to have a generic code, allowing pkt_type to be moved in struct sk_buff

pkt_type is a bit field, so compiler cannot really help us to find
its offset. Let's use a helper for this : It will throw a one time
message if pkt_type no longer starts at a byte boundary or is
no longer a 3bit field.
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o ipv4 address was not getting programmed properly because of
  improper byte order conversion
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Makes more sense to have randomly generated address by default than to
have all zeroes. It also allows user to for example put the bond into
bridge without need to have any slaves in it.

Also note that this changes only behaviour of bonds with no slaves. Once
the first slave device is enslaved, its address will be used (no change
here).

Also, fix dev_assign_type values on the way.
Reported-by: Pavel Šimerda <psimerda@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of jumping aroung bugs that are easily fixed just don't let them in:
affected drivers should be either fixed or have NETIF_F_HW_VLAN_FILTER
removed from advertised features.

Quick grep in drivers/net shows two drivers that have NETIF_F_HW_VLAN_FILTER
but not ndo_vlan_rx_add/kill_vid(), but those are false-positives (features
are commented out).

OTOH two drivers have ndo_vlan_rx_add/kill_vid() implemented but don't
advertise NETIF_F_HW_VLAN_FILTER. Those are:

+ethernet/cisco/enic/enic_main.c
+ethernet/qlogic/qlcnic/qlcnic_main.c
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>