- 30 Jan, 2017 40 commits
-
-
Colin Ian King authored
trivial fix to spelling mistake in cobalt_info message. Anders Celsius was the Swedish astronomer. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Colin Ian King authored
trivial fix to spelling mistake of function name in err message, should be cx24123_pll_calculate instead of cx24123_pll_calcutate. Signed-off-by:
-
Nicolas Iooss authored
In vpfe_s_fmt(), when the sensor format and the requested format were the same, bpp was assigned to vpfe->bpp without being initialized first. Grab the bpp value that is currently used by using __vpfe_get_format() instead of its wrapper, vpfe_try_fmt(). This use of uninitialized variable has been found by compiling the kernel with clang. Fixes: 417d2e50 ("[media] media: platform: add VPFE capture driver support for AM437X") Cc: stable@vger.kernel.org Signed-off-by:
Nicolas Iooss <nicolas.iooss_linux@m4x.org> Signed-off-by:
-
Hans Verkuil authored
Document the EIO error since this can happen anywhere anytime and applications should be aware of this. Also fix typo: exaustive -> exhaustive Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Soren Brinkmann authored
Add 3840x2160 as valid resolution for the webcam capture input and adjust the webcam intervals accordingly. Signed-off-by:
Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by:
-
Corentin Labbe authored
Commit d78c16cc ("ARM: SAMSUNG: Remove remaining legacy code") removed the Kconfig symbol PLAT_S5P. This patch remove the last occurrence of this symbol. Signed-off-by:
Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by:
-
Corentin Labbe authored
s5p-cec: does not use any miscdevice so this patch remove this unnecessary inclusion. Signed-off-by:
-
Lars-Peter Clausen authored
The adv7604 driver platform data contains fields for configuring the drive strength of the output pins. When probing the driver through DT these fields are not explicitly initialized, which means they are left at 0. This is a reserved setting for the drive strength configuration though and can cause signal integrity issues. Whether these signal integrity issues are visible depends on the PCB specifics (e.g. the higher the load capacitance for the output the more visible the issue). But it has been observed on existing solutions at high pixel clock rates. Initialize the drive strength settings to the power-on-reset value of the device when probing through devicetree to avoid this issue. Fixes: 0e158be0162b ("adv7604: Add DT support") Signed-off-by:Lars-Peter Clausen <lars@metafoo.de> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by:
-
Bhumika Goyal authored
v4l2_subdev_{core/video}_ops structures are stored in the fields of the v4l2_subdev_ops structure which are of type const. Also, v4l2_subdev_ops structure is passed to a function having its argument of type const. As these structures are never modified, so declare them as const. Done using Coccinelle:(One of the scripts) @r1 disable optional_qualifier @ identifier i; position p; @@ static struct v4l2_subdev_core_ops i@p = {...}; @ok1@ identifier r1.i; position p; struct v4l2_subdev_ops obj; @@ obj.core=&i@p; @bad@ position p!={r1.p,ok1.p}; identifier r1.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r1.i; @@ +const struct v4l2_subdev_core_ops i; File size before: text data bss dec hex filename 858 576 0 1434 59a soc_camera/soc_camera_platform.o File size after: text data bss dec hex filename 1234 192 0 1426 592 soc_camera/soc_camera_platform.o Signed-off-by:Bhumika Goyal <bhumirks@gmail.com> Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Christophe JAILLET authored
If 'ov9640_reg_read()' does not return 0, then 'val' is left unmodified. As it is not initialized either, the return value can be anything. It is likely that returning the error code was expected here. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Sean Young authored
The staging lirc_imon driver contains 4 usb ids. Two of those have a VFD and two don't. The VFD code is exactly the same in the mainline imon driver, so that part is easily ported. The staging driver produces raw IR rather than scancodes for the four devices, so I've ported the raw IR code from staging to mainline imon. Now that mainline imon can handle these four devices, lirc_imon is no longer needed. Compile tested only. Signed-off-by:
Sean Young <sean@mess.org> Cc: Venky Raju <dev@venky.ws> Cc: Jarod Wilson <jarod@redhat.com> Cc: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Sean Young authored
This driver is for an old mach64 VT board, which also has a framebuffer driver (atyfb) and userspace mach64 X driver. It was merged in 2010 and noone has attempted to port it to rc-core, which would be necessary to get it out of staging. I have not been able to track down the hardware either. Signed-off-by:
-
Sean Young authored
The lirc_parallel driver was merged in 2010 and noone has attempted to do the work necessary to get it out of staging (i.e. port it to rc-core). I have not been able to find one of these devices, and a machine with a parallel port is pretty rare too. Signed-off-by:
-
Sean Young authored
Before this driver can be moved out of staging, it should be ported to rc-core. I've tried to make the minimum changes possible without upsetting checkpatch. Compile tested only. Signed-off-by:
-
Sean Young authored
This driver was written using lirc since rc-core did not support transmitter-only hardware at that time. Now that it does, port this driver. Compile tested only. Signed-off-by:
-
Andi Shyti authored
The ir-spi is a simple device driver which supports the connection between an IR LED and the MOSI line of an SPI device. The driver, indeed, uses the SPI framework to stream the raw data provided by userspace through an rc character device. The chardev is handled by the LIRC framework and its functionality basically provides: - write: the driver gets a pulse/space signal and translates it to a binary signal that will be streamed to the IR led through the SPI framework. - set frequency: sets the frequency whith which the data should be sent. This is handle with ioctl with the LIRC_SET_SEND_CARRIER flag (as per lirc documentation) - set duty cycle: this is also handled with ioctl with the LIRC_SET_SEND_DUTY_CYCLE flag. The driver handles duty cycles of 50%, 60%, 70%, 75%, 80% and 90%, calculated on 16bit data. The character device is created under /dev/lircX name, where X is and ID assigned by the LIRC framework. Example of usage: fd = open("/dev/lirc0", O_RDWR); if (fd < 0) return -1; val = 608000; ret = ioctl(fd, LIRC_SET_SEND_CARRIER, &val); if (ret < 0) return -1; val = 60; ret = ioctl(fd, LIRC_SET_SEND_DUTY_CYCLE, &val); if (ret < 0) return -1; n = write(fd, buffer, BUF_LEN); if (n < 0 || n != BUF_LEN) ret = -1; close(fd); Signed-off-by:Andi Shyti <andi.shyti@samsung.com> Signed-off-by:
-
Andi Shyti authored
Document the ir-spi driver's binding which is a IR led driven through the SPI line. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Andi Shyti authored
Raw IR transmitters do not need any thread listening for occurring events. Check the driver type before running the thread. Signed-off-by:
-
Andi Shyti authored
IR raw transmitter driver type is specified in the enum rc_driver_type as RC_DRIVER_IR_RAW_TX which includes all those devices that transmit raw stream of bit to a receiver. The data are provided by userspace applications, therefore they don't need any input device allocation, but still they need to be registered as raw devices. Suggested-by:
-
Andi Shyti authored
Move the input device allocation, map and protocol handling to different functions. Signed-off-by:
-
Andi Shyti authored
The driver type can be assigned immediately when an RC device requests to the framework to allocate the device. This is an 'enum rc_driver_type' data type and specifies whether the device is a raw receiver or scancode receiver. The type will be given as parameter to the rc_allocate_device device. Change accordingly all the drivers calling rc_allocate_device() so that the device type is specified during the rc device allocation. Whenever the device type is not specified, it will be set as RC_DRIVER_SCANCODE which was the default '0' value. Suggested-by:
-
Antti Seppälä authored
Nuvoton-cir utilizes the encoding capabilities of rc-core to convert scancodes from user space to pulse/space format understood by the underlying hardware. Converted samples are then written to the wakeup fifo along with other necessary configuration to enable wake up functionality. Signed-off-by:
Antti Seppälä <a.seppala@gmail.com> Signed-off-by:
James Hogan <james@albanarts.com> Signed-off-by:
-
James Hogan authored
Add the s_wakeup_filter callback to the rc-loopback driver, which instead of setting the filter just feeds the scancode back through the input device so that it can be verified. Signed-off-by:
-
James Hogan authored
Add support in rc-core for drivers which implement the wakeup scancode filter by encoding the scancode using the raw IR encoders. This is by way of rc_dev::encode_wakeup which should be set to true and rc_dev::allowed_wakeup_protocols should be set to the raw IR encoders. We also do not permit the mask to be set as we cannot generate IR which would match that. Signed-off-by:
-
Sean Young authored
Add the capability to encode Sony scancodes as raw events. Sony uses pulse length rather than pulse distance. Signed-off-by:
-
Sean Young authored
Add the capability to encode Sharp scancodes as raw events. Signed-off-by:
-
Sean Young authored
Add the capability to encode Sanyo scancodes as raw events. Signed-off-by:
-
Sean Young authored
Add the capability to encode JVC scancodes as raw events. Signed-off-by:
-
James Hogan authored
Add the capability to encode NEC scancodes as raw events. The scancode_to_raw is pretty much taken from the img-ir NEC filter() callback, and modulation uses the pulse distance helper added in a previous commit. Signed-off-by:
-
Antti Seppälä authored
Add the capability to encode RC-6 and RC-6A scancodes as raw events. The Manchester modulation helper is used several times with various timings so that RC-6 header preamble, the header, header trailing bit and the data itself can be modulated correctly. Signed-off-by:
-
James Hogan authored
Add the capability to encode RC-5, RC-5X and RC-5-SZ scancodes as raw events. The Manchester modulation helper is used, and for RC-5X it is used twice with two sets of timings, the first with a short trailer space for the space in the middle, and the second with no leader so that it can continue the space. The encoding in RC-5-SZ first inserts a pulse and then simply utilizes the generic Manchester encoder available in rc-core. Signed-off-by:
-
James Hogan authored
Add IR encoding helper for pulse-distance modulation as used by the NEC protocol. Signed-off-by:
-
Antti Seppälä authored
Adding a simple Manchester encoder to rc-core. Manchester coding is used by at least RC-5 and RC-6 protocols and their variants. Signed-off-by:
-
James Hogan authored
Add a callback to raw ir handlers for encoding and modulating a scancode to a set of raw events. This could be used for transmit, or for converting a wakeup scancode to a form that is more suitable for raw hardware wake up filters. Signed-off-by:
-
Sean Young authored
unknown and other are for IR protocols for which we have no decoder, so the raw IR drivers have no chance of generating them. cec is not an IR protocol. Signed-off-by:
-
Sean Young authored
Now that we can select the exact variant of the protocol for wakeup filter, the winbond-cir can use the wakeup filter rather than module parameters. Signed-off-by:
-
Sean Young authored
There are two different encodings used for nec32: - The ir-nec-decoder.c decoder treats it as 32 bit msb first. - The img-ir decoder/encoder, winbond wakeup, dib0700, ir-ctl userspace, treat nec32 analogous to necx and nec: 4 bytes, each lsb first. So this format reverses the 4 bytes. There are arguments to be had for both formats, but we should not use different formats in different parts of the kernel. Selecting the second format introduces the least code churn. It does mean that the TiVo keymap needs updating. This change was submitted before as "18bc1744 [media] media: rc: change 32bit NEC scancode format", which was reverted because it was unclear what scancode rc drivers produce. There are now more examples of drivers which produce nec32 in lsb format. The TiVo keymap is verified against the Nero Liquid TiVo remote. The keymap is not for the Tivo DVR remote, which uses rc-5. Signed-off-by:
-
Sean Young authored
We need to valdiate that scancodes are valid for their protocol; an incorrect necx scancode could actually be a nec scancode, for example. Signed-off-by:
-
Sean Young authored
For IR wakeup, a driver has to program the hardware to wakeup at a specific IR sequence, so it makes no sense to allow multiple wakeup protocols to be selected. In the same manner the sysfs interface only allows one scancode to be provided. In addition, we need to know the specific variant of the protocol. In short, these changes are made to the wakeup_protocols sysfs entry: - list all the protocol variants rather than the protocol groups, e.g. "nec nec-x nec-32" rather than just "nec". - only allow one protocol variant to be selected rather than multiple - wakeup_filter can only be set once a protocol has been selected in wakeup_protocols. This is an API change, however the only user of this API is the img-ir, but the wakeup code was never merged to mainline, so it was never used. Signed-off-by:
-
Sean Young authored
There are many variants of extended rc5. This implements the 20 bit version. Signed-off-by:
-
