CHANNEL_CCK flag is set for all 2 Ghz channels, so IS_CHAN_CCK() would
turn out to be true for all channles in that band.
Use IS_CHAN_B() now, which checks the channel mode and not the channel
flags.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Also, use a helper function to setup RC status data
when processing completed TX descriptors.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Break down huge functions, use helper functions or
macros instead.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Replace TRUE/FALSE macros with VALID/INVALID macros.
Follow a consistent variable convention.
Remove unnecessary comments.
Add all RC phy macros into a single enum.
Merge functions into reasonably sized entities.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Maintaining two sets of rate tables is redundant, remove one
and use struct ath_rate_table exclusively.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove the hack using vif, and use rate_driver_data within
skb->cb to hold driver specific rate information.
Setup the rate series in the skb's tx control area and remove
all references to ath9k specific rate series ( using struct ath_rc_series ).
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Move the hw rate tables to ath_softc, and access them directly.
tx_triglevel_max is global, move it to ath_rate_node.
Now that ath_rate_softc is gone, rate control attach becomes simpler.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Rate control init is now confined to itself, using the
HT capabilites of the STA from rate_init().
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove a lot of old, crufty code and make
RX status reporting a bit sane and clean.

Do not do anything to the RX skb before unmapping.
So in ath_rx_tasklet(), move the skb_put() after PCI unmap.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Half/Quarter rate tables are needed only for legacy chipsets.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Setup legacy rates in ath_rate_init() itself.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Avoid casting of ath_tx_ratctrl and access the elements directly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 [ 6133.670329] BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
 [ 6133.672802] IP: [<ffffffffa030fcf6>] ieee80211_stop_queues+0x26/0x40 [mac80211]
 [ 6133.672802] PGD 759dc067 PUD 74f1d067 PMD 0
 [ 6133.672802] Oops: 0002 [#1] PREEMPT SMP
 [ 6133.672802] last sysfs file: /sys/class/backlight/acpi_video0/brightness
 [ 6133.672802] CPU 0
 [ 6133.672802] Modules linked in: ath9k(-) mac80211 pciehp pci_hotplug arc4 ecb joydev pcmcia ppdev lp ppp_generic psmouse sg pcspkr s]
 [ 6133.735830] Pid: 4445, comm: rmmod Tainted: G        W  2.6.28-rc5-wl #1
 [ 6133.735830] RIP: 0010:[<ffffffffa030fcf6>]  [<ffffffffa030fcf6>] ieee80211_stop_queues+0x26/0x40 [mac80211]
 [ 6133.735830] RSP: 0018:ffff88007d1efd10  EFLAGS: 00010246
 [ 6133.735830] RAX: 0000000000000000 RBX: ffff880074f41aa0 RCX: 0000000000000000
 [ 6133.735830] RDX: 0000000000000010 RSI: 0000000000000000 RDI: ffff880074f40340
 [ 6133.735830] RBP: ffff880074990000 R08: 0000000000000000 R09: 000000000000224d
 [ 6133.735830] R10: 0000000000000000 R11: ffffffff8031dc70 R12: 0000000000000000
 [ 6133.735830] R13: 0000000000000001 R14: ffff880074f46c9c R15: 0000000000000000
 [ 6133.735830] FS:  00007f1e2e0bc6f0(0000) GS:ffffffff805e0b80(0000) knlGS:0000000000000000
 [ 6133.735830] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
 [ 6133.735830] CR2: 0000000000000010 CR3: 0000000075593000 CR4: 00000000000006e0
 [ 6133.735830] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 [ 6133.735830] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
 [ 6133.735830] Process rmmod (pid: 4445, threadinfo ffff88007d1ee000, task ffff88007c0c8000)
 [ 6133.735830] Stack:
 [ 6133.735830]  ffffffffa034d583 ffff88007c7d9410 ffff88007c7d9410 ffff88007c7d9410
 [ 6133.735830]  ffffffff80481dab ffff880074f41aa0 00000000fffffff0 0000000000000000
 [ 6133.735830]  0000000000000001 0000000000000001 ffffffffa034d8a5 ffff88007c7d9400
 [ 6133.735830] Call Trace:
 [ 6133.735830]  [<ffffffffa034d583>] ? ath_radio_disable+0x33/0x150 [ath9k]
 [ 6133.735830]  [<ffffffff80481dab>] ? __mutex_lock_slowpath+0x20b/0x2a0
 [ 6133.735830]  [<ffffffffa034d8a5>] ? ath_sw_toggle_radio+0x65/0xa0 [ath9k]
 [ 6133.735830]  [<ffffffffa019d1f4>] ? rfkill_toggle_radio+0x74/0x140 [rfkill]
 [ 6133.735830]  [<ffffffffa019d597>] ? rfkill_remove_switch+0x67/0x80 [rfkill]
 [ 6133.735830]  [<ffffffffa019d955>] ? rfkill_unregister+0x25/0x50 [rfkill]
 [ 6133.735830]  [<ffffffffa034bf75>] ? ath_detach+0xf5/0x140 [ath9k]
 [ 6133.735830]  [<ffffffffa034bfe9>] ? ath_pci_remove+0x29/0x80 [ath9k]
 [ 6133.735830]  [<ffffffff8035263c>] ? pci_device_remove+0x2c/0x60
 [ 6133.735830]  [<ffffffff803c3829>] ? __device_release_driver+0x99/0x100
 [ 6133.735830]  [<ffffffff803c3950>] ? driver_detach+0xc0/0xd0
 [ 6133.735830]  [<ffffffff803c296e>] ? bus_remove_driver+0x8e/0xd0
 [ 6133.735830]  [<ffffffff80352916>] ? pci_unregister_driver+0x36/0xa0
 [ 6133.735830]  [<ffffffffa0356ad4>] ? exit_ath_pci+0x10/0x29 [ath9k]
 [ 6133.735830]  [<ffffffff8026bb1b>] ? sys_delete_module+0x1cb/0x2d0
 [ 6133.735830]  [<ffffffff802960d9>] ? do_munmap+0x349/0x390
 [ 6133.735830]  [<ffffffff80342d01>] ? __up_write+0x21/0x150
 [ 6133.735830]  [<ffffffff8020c45b>] ? system_call_fastpath+0x16/0x1b
 [ 6133.735830] Code: c3 0f 1f 40 00 0f b7 57 5e 0f b7 47 5c 01 c2 74 30 31 c9 66 90 48 8b 57 78 0f b7 c1 48 c1 e0 07 48 03 82 00 03 00
 [ 6133.735830] RIP  [<ffffffffa030fcf6>] ieee80211_stop_queues+0x26/0x40 [mac80211]
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the commit entitled "mac80211/drivers: rewrite the rate control
API", the meaning of the packet transmit count was changed from the
number of retries to the total number.  In driver rtl8187, this change
was missed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In commit 9ea2c74 named "mac80211/drivers: rewrite the rate control API",
the meaning of status.rates[i].count was changed from number of retries
to total number of tries. As a result, the pid rate-setting algorithm fails
because every packet appears to have needed a retransmit.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When we switch off the LEDS during initialization
we kill rt73usb from proper functioning. The immediate
result after the first LED command are MCU failures
and a complete breakdown of TX/RX.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since WE7 /proc/net/wireless checks whether level and noise  are in dBm
and shows them accordingly. Indicate that we return signal and noice
levels in dBm.

Before:
Inter-| sta-|   Quality        |   Discarded packets               | Missed | WE
 face | tus | link level noise |  nwid  crypt   frag  retry   misc | beacon | 22
  eth1: 0000   65.  219.  165.       0      0    148     41      0        0

After:
Inter-| sta-|   Quality        |   Discarded packets               | Missed | WE
 face | tus | link level noise |  nwid  crypt   frag  retry   misc | beacon | 22
  eth1: 0000   65.  -37.  -91.       0      0      0      0      0        0

While at it, replace raw numbers with appropriate macro.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This makes minstrel the default rate control algorithm
for mac80211. For more information see:

http://wireless.kernel.org/en/developers/Documentation/mac80211/RateControl/minstrel

If someone can come up with a better algorithm they get a prize
(undisclosed).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211's ieee80211_register_hw() is often called within the
probe path so it cannot assume the device's driver structure
has been attached yet so to create a workqueue instead of
using driver->name use the wiphy's phy%d name. The name doesn't
really matter anyway.

This should fix sporadic oopses found when we race to beat the
driver pointer setting. Not even sure how this was working properly.

http://www.kerneloops.org/search.php?search=ieee80211_register_hwSigned-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes the poor wireless connection which happens even
if we are very well in the range.

Signed-off-by: Don.breslin@atheros.com
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As was pointed out in "p54: honour bss_info_changed's short slot time settings",
bss_info_changed provides more useful settings that can be used by the driver.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Johannes pointed out that the driver has cache the firmware for
suspend/resume cycles.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch contains only contains a one-liner fixes and enhancements
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch enables Mesh Point operation for any p54 device.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make the DMAable mameory consistent with pci_set_consistent_dma_mask().
The DMA-mapping.txt Documentation recommends this but for PCI-X
considerations and on strange architecture like SGI SN2, not sure
why it would fix an issue but lets see if it does, just in case.

Before this, this driver was tested with x86_64 with about
7 GB of RAM, not sure if this is really needed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use DMA_32BIT_MASK to clarify we only want 32-bit DMA
memory. What was there before is also 32-bit but this makes it
clearer
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of hardcoding the used in/out endpoints
we should detect them by walking through all
available endpoints.

rt2800usb will gain the most out of this, because
the legacy drivers indicate that there are multiple
endpoints available.
However this code might benefit at least rt73usb as
well for the MIMO queues, and if we are really lucky
rt2500usb will benefit because for the TX and PRIO
queues.

Even if rt2500usb and rt73usb do not get better performance
after this patch, the endpoint detection still belongs to
rt2x00usb, and it shouldn't hurt to always try to detect
the available endpoints.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After considerable testing, the initial fears that the driver might damage
some flavors of RTL8187B hardware seem to be groundless. Accordingly, the
logged warning is removed. In addition, Kconfig is changed to remove the
dependence on EXPERIMENTAL.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Realtek 8187B has a receive command queue to feedback beacon interrupt
and transmitted packet status. Use it to feedback mac80211 about status
of transmitted packets. Unfortunately in the course of testing I found
that the sequence number reported by hardware includes entire sequence
control in a 12 bit only field, so a workaround is done to check only
lowest bits.
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add conf_tx callback and use it to configure tx queues of 8187L/8187B.
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Hin-Tak Leung reported that after the change "rtl8187: add short slot
handling for 8187B" his RTL8187B started to give low throughput on
network transfers. Turns out that the SIFS setting used isn't ok, it
doesn't look to be the real aSIFSTime, using the "magical" 0x22 value
like on other 818x variants as the vendor does too fixes the issue.
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Race condition causes RX buffers to be accessed even before it is
initialized. The RX and TX buffers are initialized immediately after
the hardware is registered with mac80211. The mac80211 start callback
is ready to be fired once the device is registered for a case when the
wpa_supplicant is also running at the same time.

The same race condition is also possible for RKFILL registration
as RFKILL init happens after the device registration with mac80211
and it is possible that rfkill_register would be called even before
it is initialized.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k frees irq even before IRQs are disabled and existing IRQs
are flushed when rfkill_register() fails.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, ath9k builds RFKILL feature only when the RFKILL subsystem
is built part of the kernel. Build RFKILL feature regardless of whether
RFKILL subsystem is built as a MODULE or part of the kernel.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes incorrect noise floor threshold values.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>