This patch moves platform_add_devices() (standard declaration of devices)
outside of the platform specific device declarations. Moving to the end
of the magician_init() clarifies the source code (standard and specific
declaration are not mixed).
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Add a fake regulator, which is required for the correct initialization
of the PWM backlight driver.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
[ added a missing include for fixed regulator ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Add a debug message for the backlight brightness function.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Magician STUART port is connected to the infraport and used by the FICP
driver. The FICP driver uses its own definition.

Required for correct initialization of the pxaficp_ir driver after
planned dmaengine conversion.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

USB host ports on the HTC Magician are wrongly enabled. Port 1 is for
bluetooth and port 2 is for OTG (mux in the charger connector).
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Old definition for the physmap-flash driver is incomplete:
- Use of an EGPIO without previous request
- Missing the MTD partitions

This patch fixes it. Read functionality was tested on the machine with
board_id 0x3a. Writing was not tested.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

The pxaficp_ir driver requests a power GPIO for the transceiver internally,
so a global GPIO allocation in magician_init() is redundant.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

This patch changes fast_mode settings for the normal and power I2C
controller on the HTC Magician machine.

Connected device on the Power I2C:
- MAX1587A: working in the fast mode

Connected devices on the Normal I2C:
- UDA1380: working in the fast mode
- OV9640: bus became stuck in the fast mode

The OV9640 is not using a standard I2C protocol, but an SCCB variant. Maybe
it is not fully compatible in the fast mode. Therefore fast mode for normal
I2C is disabled. If you not using the OV9640 then you can enable the fast
mode for the UDA1380.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
[included Philipp Zabel's comment change]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

This patch fixes the charging detection functions for pda_power driver
(according to newly discovered EGPIOs) and add NiCd backup accumulator
charging support.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Change the default Samsung LCD refresh from an unrealistic 117Hz to 50Hz
as no video applications on the HTC Magician can work that fast.

The optimalization lowers the RAM latency at least by 3%.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

This patch renames EGPIOs, which are used for the charging cable presence
and type detection. Old names did not correspond with an observed
functionality (on board_id 0x3a). The behavior is not:

- AC charger
- USB charger
- Cable detection

, but:

- AC/USB type
- Cable detection1
- Cable detection2

This patch fixes a possible typo in the bit offset for the cable detection
EGPIO declaration, too.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Delays for the Samsung LCD are greater than needed. These values were
extracted from a datasheet.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

This patch renames GPIOs, which are used to control the power lines to
the LCD screen. New names correspond to a real functionality, which was
measured on the HTC Magician board_id 0x3a.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

This patch adds EGPIO pins: Infra transceiver power, NiCD charging and
inserted charger cable.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

This patch changes the description of the LCD power GPIO to be more
specific.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Optimize the debug messages for the LCD power.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Print more specific error message for global GPIOs.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

This patch fixes the indentation for the HTC Magician machine definition.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
[ split pwm_remove_table() call on 2 lines ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

The ID and period for the backlight PWM are obtained from a PWM lookup
table, so the corresponding values don't need to be duplicated into the
platform data.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

The mioa701 is using the wm9713 for audio, battery and touchscreen. Add
the missing audio part, which disappeared.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Add io memory and dma requestor lines to the irda pxa device. This is
part of the conversion of pxaficp_ir to dmaengine, and to shrink its
adherence to 'mach' includes.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Petr Cvek <petr.cvek@tul.cz>

Use for struct pxa2xx_spi_master clock_enable field was removed years ago
from the pxa2xx-spi driver by the commit 2f1a74e5 ("[ARM] pxa: make
pxa2xx_spi driver use ssp_request()/ssp_free()").

Therefore remove it from structure definition, documentation and from
couple affected board files.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Pull CRIS updates from Jesper Nilsson:
 "Mostly removal of old cruft of which we can use a generic version, or
  fixes for code not commonly run in the cris port, but also additions
  to enable some good debug"

* tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris: (25 commits)
  CRISv10: delete unused lib/dmacopy.c
  CRISv10: delete unused lib/old_checksum.c
  CRIS: fix switch_mm() lockdep splat
  CRISv32: enable LOCKDEP_SUPPORT
  CRIS: add STACKTRACE_SUPPORT
  CRISv32: annotate irq enable in idle loop
  CRISv32: add support for irqflags tracing
  CRIS: UAPI: use generic types.h
  CRIS: UAPI: use generic shmbuf.h
  CRIS: UAPI: use generic msgbuf.h
  CRIS: UAPI: use generic socket.h
  CRIS: UAPI: use generic sembuf.h
  CRIS: UAPI: use generic sockios.h
  CRIS: UAPI: use generic auxvec.h
  CRIS: UAPI: use generic headers via Kbuild
  CRIS: UAPI: fix elf.h export
  CRIS: don't make asm/elf.h depend on asm/user.h
  CRIS: UAPI: fix ptrace.h
  CRISv32: Squash compile warnings for axisflashmap
  CRISv32: Add GPIO driver to the default configs
  ...